Leakage Current Testers
-
Product
IP VIDEO MARGIN TESTER
IPMT-3
-
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
Sensor Unit for High Precision Current Sensors
CT9557
-
Hioki pull-through current sensors and clamp on current probes are best-in-class current sensing devices for use with power meters, Memory HiCorders and high performance oscilloscopes. The CT9555 is 4-channel sensor unit and power adapter for any of the CT686x series, 9709 and CT684x series current sensors and probes that provides waveform and RMS output.
-
Product
RCD & ELCB Testers
-
Shanghai Beha Electronics Co., Ltd.
*Ideal for tripping 3mA, 5mA, 10mA, 15mA, 20mA, 30mA, 50mA, 100mA, 150mA, 250mA, 300mA, 500mA RCDs*Accurate digital readout of disconnection time. *Timer Resolution 1ms (max time : 19.99s)*Zero crossing circuitry permit testing at 0° or 180°*Measure voltage between line and earth before testing.
-
Product
De-Energized Tester
MOTOR GENIE
-
The MOTOR GENIE® can see more than a megohmmeter, resistance tester, or RCL tester, making it the perfect tool for troubleshooting, startup, and quality control of low voltage AC induction motors.
-
Product
AMIDA IPM Tester
3001XP
-
HVI Source:16 Channels 4Q V/I Source; Two zero ref. floating GND ; ±30V, ±200mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% Accurate reading of Range
-
Product
High Current Probes (Power Electronics) HCF33009S210L210
1001366
-
The HCF33009S210L210 High Current Probe is specifically designed for high-performance power electronics applications, providing exceptional handling of current up to 14.00 A with a robust typical contact resistance of only 15.00 mΩ. This probe features a unique basic contact design with a pitch of 3.00 mm, allowing for precise integration into various electronic systems. Capable of operating in extreme temperatures ranging from -45°C to +200°C, it provides reliability and accuracy in demanding environments.
-
Product
Winding Resistance Tester
JYR-50C/40C/20C
-
1. With demagnetization function.2. Testing range reach to 20k3. Also apply to testing tranformer with high winding resistance.
-
Product
Digital LOOP/PSC/LOAD Tester
1825 LP
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures the voltage drop as if 16A was flowing between Line and Neutral.● Displays voltage without current (V at 0A).● Display voltage as if 16A flowing between Line and Neutral (V at 16A).● Loop test for L-E● PSC between L-N.● Single one smart push button operation; ON, Scroll through results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software range).● Combined prospective short circuit current, loop and load tester.● Display can be customized for large orders.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Multifunctional Scratch Hardness Tester
-
Sataton Instruments Technology CO., Ltd
Multifunctional scratch hardness tester is an integrated testing instrument designed for cross hatch cut method and five-finger (five arm) method to measure scratch or mar resistance, hardness, susceptibility of a material surface to different physical damage like scratching, marring, scraping, etc. The tester are made of two parts, one is for determination of resistance to scratches and cuts according to cross-cut test for paints and varinishes. The other is for
-
Product
AMIDA ATI 600 Tester
-
AMIDA ATI 600 Tester is a dedicated test system for semiconductor components (MOSFET, BJT, DIODE, ... etc.), which can accurately and quickly measure product parameters through form filling and editable program control. In practical applications, AMIDA ATI 600 Tester is the best choice for users, whether it is CP or FT mass production testing, or research projects of component characteristics.
-
Product
Capacitors - Power - Heavy Current (ESTA)
-
Vishay ESTA is one of the few manufacturers to offer a complete range of power capacitors. These cost-effective devices for harmonic control, energy savings, and voltage stabilization are highly reliable and environmentally safe, and can be used under the most rugged conditions. Vishay ESTA power capacitors address a wide range of energy-generation applications. Their “green” applications include energy generation in on- and off-shore wind turbines and solar power plants.
-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
Product
Hand-held Cable Tester
STM-8
-
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
Product
COMPUTER MONITOR TESTER
MT160
-
Test a wide variety of PC & Mac computer monitors-all in one unit. Extended scanning formats range from 15.7K to 80 KHz.
-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
Insulation Resistance Tester
UDH-50-1-T
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated•Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV •Resistance range to 1TΩ •Continuous digital display on LCM•Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
Product
Eddy Current Array
BRIO
-
BRIO is an advanced, ultra-portable Eddy Current Array (ECA) instrument designed for in-service inspections in aerospace, oil & gas, power generation, and manufacturing industries.
-
Product
Shore Hardness Tester
DRK201
-
Shandong Drick Instruments Co., Ltd.
The Shore hardness tester is applied to test the hardness of vulcanized rubber and plastic.
-
Product
Vacuum Interrupter Tester
VIT
-
Veer Electronics make Vacuum Interrupter Tester that tests the Vacuum Interrupter Integrity by applying a Pulse DC Voltage across the Interrupter under Test. When this Voltage is applied to the Vacuum Interrupter, if Interrupter is defective then an electronic Buzzer gives Audio indication as well as Red color LED will gives Fail Indication. If Interrupter is in Healthy Condition, then the Instrument will gives Pass Indication with Green LED light.
-
Product
Tube Tester / Tube Checker
RM 1
-
The RM 1 is a Vacuum Tube Tester easy to handle, in its construction almost unique, which enables a fast, simple and precise plate current measurement (emission test) of the most common double triodes (6SL7-GT, 12AT7=ECC81, 12AU7=ECC82, 12AX7=ECC83)¹ and power pentodes (6CA7=EL34, KT66, KT88, 6550, 6L6-GC, 5881, 6V6-GT, 6BQ5=EL84)¹. The device has a distinct classic design, primarily consisting of a solid beech wood cabinet and a front panel of anodized aluminium. Because of its small dimensions it is easily transported and it doesn't need a lot of space for accommodation.
-
Product
SoC Tester
UltraFLEXplus
-
The UltraFLEXplus combines new instrument and software capability with a revolutionary tester infrastructure that provides a step-function improvement in throughput and engineering efficiency – all while leveraging the cumulative test IP developed over the UltraFLEX’s 15 year history .
-
Product
Box Compression Tester
BCT-03
-
Jinan Leading Instruments Co., Ltd.
BCT-03 Box Compression Tester is professionallyused to test the compression resistance property of carton box, corrugated box,honeycomb cardboard box and other packaging. And it’s also applicable tocontainer compression test of plasticbucket (edible oil, mineral water), fiber drum, carton, paper, cans, containerbarrels (IBC barrels).
-
Product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
Product
Bit Error Rate Tester
Eye-BERT Gen2
-
The Eye-BERT Gen2 builds on our original Eye-BERT, adding extended data rates, mixed mode testing capability, and a color touch screen. The extended data rate allows for testing of links in the 125Mb to 11.4Gb range all in a single unit. The Eye-BERT Gen2 offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of SFP and SFP+ transceivers as well as link verification and performance testing all in a single unit.
-
Product
Contacts Resistance Tester
JYK II
-
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Product
Voltage, Current and Power Measurement
-
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
Product
High Current Probes (Power Electronics) HCF32009S135N130
1003498
-
The High Current Probes (Power electronics) HCF32009S135N130 is engineered for precision and durability in power electronics applications. With a pitch of 2.54 mm and capable of operating under extreme temperatures ranging from -45°C to +200°C, this basic contact probe offers reliable performance in diverse environments. Its innovative design allows for a continuous current rating of 12 A and a remarkably low contact resistance of 20 mOhm, making it ideal for high-efficiency systems where minimal resistance is crucial.
-
Product
30A, 50MHz High Sensitivity Current Probe
CP030A
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
