Leakage Current Testers
-
Product
Iron loss Testers
ATS Series
-
Hunan Linkjoin Technology Co., Ltd.
Linkjoin Iron Loss Testers
-
Product
Current Transformers
-
Supreme Instrument Laboratories
Portable Low Tension precision grade multi ratio Current Transformers, housed in laminated wooden cabinet, wound primary with suitable terminals on highly insulated bakelite panel upto 100 Amps. For higher ranges, a centre hole is provided for passing primary conductors for desired range.
-
Product
Through Hole Type AC Current Sensor
CTA-120A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*High accuracy and compact size.*Wide measuring range:AC 1A～120A.
-
Product
Substation Series Testers
GTPD-92
-
Partial discharge（PD） is a pulsed discharge that produces a series of physical phenomena and chemical changes such as light, sound, electrical and mechanical vibrations in and around electrical equipment.
-
Product
Megohmmeter Insulation Tester
AMIC-30
-
The AMIC-30 insulation tester is a small portable meter designed to measure insulation resistance in electrical and telecommunications installations, cables, motors, transformers and other equipment. The test voltage can be programmed in steps from 10 V to 1000 V. The instrument can measure both insulation resistance over a wide range (0,1kΩ...100GΩ), and insulation leakage current, capacitance and other parameters. All test results can be stored in the internal memory and sent to a computer via the included wireless USB receiver. The meters are supplied with rechargeable Ni-Cd batteries.
-
Product
Installation Testers
-
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
Product
Universal Cable/Harness Tester
LX-686
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface,．·Up to 1500Vdc/1000Vac Test Voltage ,．·256 Max. Test Points , (Max of all series)．·500 Max Files Memory,support USB or PC unlimited expansion,．·Arc detection level 0-9 ,auto prompt．·Adopted high resolution colour 640*480 TFT LCD ,．·Providing Single-End ,Multi-segment ,Standard ,and Spot test of wire.．·Auto Scan and Auto Pin Search ,．·The system provides advanced instant open-circuit, short-circuit, continuity test,．·Intermittent Conductance Test,．·Intermittent Open/Short Test ,．·Full Programming Sequence Test ,．·Versatile I/O Ports for application ,．·Statistics and Print Function,．·Provide REMOTE interface, communicate with PLD auto test fixture,．·Provide personalized customization according to different requirements,
-
Product
Specialty Testers
-
Klein Tools has a wide range of specialty testers, each designed to meet the needs of specific trade professionals. All testers are engineered to give the most accurate readings possible while standing up to the tough jobsite conditions encountered by tradespeople every day.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-02
Current Input Module
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
DIN Abrasion Tester
TF215
-
TESTEX Testing Equipment Systems Ltd.
DIN Abrasion Tester, to determine abrasion of flexible materials, such as rubber, tires, transmission belts, soles, leather etc. The abrasion tester is provided with a wide testing area to meet the most requests. Additional balance is required.
-
Product
LATCH UP Tester
-
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
Product
Dual Surge Current Generator
MIG0612T-K12
-
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
Product
Socket Tester
-
*Power supply from mains : 200-230V AC*Transmit AC signal through concrete walls; Shielded / armored cable*Internal fuse protection
-
Product
VGA in Tester
M-IPC-520B
-
Fuzhou Metricu Technology Co Ltd
Analog camera testIP camera test, support onvif, 4K, H.264 and H.2658MP TVI test, 8MP CVI test, 8MP AHD testVGA input, support 1920 x 1200P 60FPS
-
Product
Digital Clamp Tester
MCL-550D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・55mmφCT window and Multi Function・AC Line Current up to 1000A・AC/DC Voltage, Resistance, Continuity Check & Diode Test・Conform to IEC safety requirements (IEC1010-1, CAT III 600V)
-
Product
Box Compression Tester
BCT-03
-
Jinan Leading Instruments Co., Ltd.
BCT-03 Box Compression Tester is professionallyused to test the compression resistance property of carton box, corrugated box,honeycomb cardboard box and other packaging. And it’s also applicable tocontainer compression test of plasticbucket (edible oil, mineral water), fiber drum, carton, paper, cans, containerbarrels (IBC barrels).
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-80
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of main cable*BIG CT WINDOW*AC 1mA～500A
-
Product
British Pendulum Skid Tester
SG-BM-II
-
The instrument which is direct reading, gives a measure of the friction between a rubber slider and wet road surface. It provides the Highway Engineer with a practical means of obtaining reliable scientific evidence on which to take the appropriate measures to reduce skidding.It also can be used for testing slip resistance of floors and sports surfaces.Satisfies the following standards: EN 13036-4 EN 1097-8, ASTM E103, and BS812: 114, NLT 174, CNR No 105, 140 & Australian Standard (AS3661.1: 1993).
-
Product
High Voltage Tester
-
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
Product
Emission Testers
-
Maschinenbau Haldenwang GmbH & Co. KG.
A device that monitors the composition of the flue gas of a boiler heating unit to determine if the mixture of air and fuel is at the proper ratio for maximum heat output.
-
Product
Logger version 2-D electro-magnetic current meter
INFINITY-EM AEM-USB
-
Infinity EM is an autonomously deployable EM (electro-magnetic) current meter with a data logger. Due to the principle, the instrument provides high accurate 2-D current measurements in even low scatter fields, where ADVs (Acoustic Doppler Velocimeter) has difficulties. The measurement range is wide from 0 to ± 500 cm s-1. The instrument design is compact (1.0kg in air). Infinity EM allows for current velocity measurements virtually anywhere.
-
Product
Bally Flexing Tester
TF116
-
TESTEX Testing Equipment Systems Ltd.
Bally flexing Tester is designed for flexing resistance test to be and ingor other types of failure at flexing creases. The machines applicable to all flexible materials,in particular leathers, artificial leather below thickness
-
Product
Oil Tan Delta Tester / Tester System
-
The instrument is designed to test the insulation resistance of electronic and electrical components in the range of 1 Meg ohm to 10 Million Meg ohm.
-
Product
LED Testers
-
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
Product
Other Testers
-
Logic Probe, Digital Pulser, Voltage Tester, Circuit Tester, Analog Type Battery Tester.
-
-
Product
Water Content Testers
-
Water content tester, cloulometric Karl Fischer titrator, crude petroleum water content tester
-
Product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
-
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
Mini AC Leakage Current Clamp Tester (CE)
M-140
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*40mmφCT window and ultra compact size.*Least affection from the external magnetic field.*Wide current measurements.(AC0.01mA-300A)
-
Product
Static Tester for Lab and Workshop
ADSE 715 RS
-
The ADSE 715 is a complete high performance single pressure Ps stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air data computers ) and sensors. The high precision embedded sensors enable the ADSE 715 to be used as a pressure standard. The user interface running on a PC connected through USB link is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
