PXI Controllers
-
Product
Crossing Control Bypass Switch
XCBS
-
The XCBS is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the crossing control circuits to the designated terminals on the XCBS. The rotating "knife switch" on the left side of the XCBS allows the crossing warning system to be controlled for manual test purposes. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. The non-removable bypass key adds an additional level of security for the Bypass function. Optional hookup can be made to the auxiallary terminals to include the activation of a strobe or event recorder input when the XCBS is placed in the "bypass" position.
-
Product
Control Module
ZET 7160-S
-
ZET 7160-S is a step engine control digital unit with CAN 2.0 interface. A step control signal is fed from the digital port. It determines the number of steps the step engine must be turned by, and the speed the step engine is to move with.
-
Product
Scienlab Measurement & Control Module
SL1062A
Communications Module
The Measurement & Control Module SL1062A is portable temperature measuring module for record thermocouple - temperature sensors of type K for a temperature range of -100 to +1300 °C and with 16 channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
Product
Intelligent Pressure Display Controller
HR5310/HR5311
-
HighReach Measuring & Controlling System Co.,Ltd
HR5310 intelligent pressure display controller is an intelligent pressure measurement and control product that integrates pressure measurement, display, output and control, with RS485 digital interface; the product is a fully electronic structure, using international brand pressure sensors, high-precision A/D conversion, microprocessor operation processing, on-site display, and output of one analog quantity and five switch quantities.The intelligent digital pressure controller is flexible to use, simple to operate, easy to debug, safe and reliable, and is widely used in hydropower, tap water, petroleum, chemical, machinery, hydraulic and other industries to measure, display and control the pressure of fluid media.
-
Product
Differential Temperature Controller
-
Normal temperature controller acts on one single input and tries and maintain that temperature at a pre programmed constant level. A differential temperature controller as the name suggest, takes two temperature inputs and tries to maintain the difference between these two temperatures as constant. This is widely used in today’s innovation Solar Energy Systems to provide maximum operating efficiency and flexibility. It automatically maintains the difference e.g., In case of self powered solar box furnace or in case of a solar water collector. By automatically switching on a fan or a pump the temperatures can be equalized.
-
Product
Solid State Synchro Control Transformer and Solid State Resolver Control Transformer
SCT-RCT Series
-
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
Product
Temperature and Humidity Control Systems
-
ETS 5000-Series controllers—with an industry-leading combination of features and economy—feature dual-function controllers for humidity, temperature, and third parameter control (e.g. pressure or oxygen). Our latest generation of microprocessor (PID) controllers offer precision and accuracy and can be used with or without software. All controllers include a sensor.
-
Product
RF Power Controller (ALC)
310-010030-004
-
The serial controlled ALC module is used to set and monitor the output level of your fixed gain RF amplifier. The module is available for many bands between 800 MHz and 3 GHz, and is configured and calibrated to meet your requirements.
-
Product
Analyze, Monitor and Control
Analysis Pack
-
Blue Cat's Peak Meter Pro plug-in will tell you everything about your audio levels. Blue Cat's FreqAnalyst Pro and FreqAnalyst Multi plug-ins provide extremely smooth spectrum and frequency content analysis. Finally, the StereoScope plug-ins series let you visualize the stereo image of your audio content in details.
-
Product
USB/Ethernet Control Step Attenuator
-
Digital control attenuators with Ethernet or USB control
-
Product
PH / ORP Monitor / Controllers
720 Series II
-
The advanced “isolated” circuitry of the 720 Series II pH/ORP Monitor/ controllers guarantees accurate and reliable measurements — completely eliminating ground-loop and noise issues. The unique sensor preamp allows for longer distances between the sensor and the Monitor/controller without the loss of accuracy or reliability.
-
Product
Control IPC
AMAX-5000 Series
-
AMAX-5000 is an EtherCAT Slice I/O and controller platform designed with the smallest programmable automation controller (PAC) in the Core i class.
-
Product
Audio Video Controllers
-
Most of our cameras can operated remotely. The controllers allow to control the functions of the cameras:– Zoom– Focus– Audio– Pant/Tilt– optionally iris– LANThe controllers convert the optical signal to electrical signalsFor most controllers there is the option to integrate an Ethernet interfaceMost of the controllers can be equipped with an option for shielded intercom. The microphone is either integrated in the housing or a separate microphone can be used.If more than one camera is in use (e.g. one fixed and one mobile camera) multi controllers allow to control several cameras with one device.Up to 4 cameras can be connected to one multi controller. Each camera can be connected to a separate monitor each one monitor can show the selected camera.
-
Product
Voltage Controlled Variable Attenuators
-
A voltage variable attenuator is an electronic device that provides a variable attenuation depending on the voltage applied
-
Product
Pressure Control Setup Using Pid Controller
ULP-26
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Z-Axis Drive and Controller
MFC-2000
-
Applied Scientific Instrumentation
The MFC-2000 has been specifically designed to provide a high resolution and highly repeatable, means of controlling the focus/Z position of the microscope stage. Precise control of the microscope's focus is obtained through the use of a closed-loop DC servomotor employing high resolution encoders for positioning feedback. By using closed-loop control of the focus position, there is no chance that the focus point can be lost as can occur with open-loop stepper motors.
-
Product
CCCP Controller
-
CCCP is the technology behind Nüvü Camēras’ extraordinary sensitivity in low light imaging. The patented controller generates significantly less clock-induced charges (CIC) than any other CCD controller during charge transfer throughout the EMCCD (down to an average below 0.001 ē/pixel/frame), therefore allowing for greater EM gain to ultimately attain sub-electron readout noise.
-
Product
Ethernet Controlled Relays And Relay Drivers
-
*ICS's Ethernet to Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Ethernet to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE or with RPC commands from any Linux/Unix or MAC computer. Use ICS's interactive VXI-11 Keyboard program for easy operation from your PC without having to write a program.
-
Product
Gas Control
-
Teledyne has decades of experience to offer a full line of thermal mass flow meters and mass flow controllers. Our products provide solutions for a wide range of applications which include high and low flow ranges, corrosive gases and very high-temperature environments. With the assistance of our experienced application engineers and global sales network, we will help you find a reliable, repeatable and durable solution for applications in both laboratory and industrial environments. Your needs can be met by using quality flow instruments designed and manufactured by Teledyne Hastings.
-
Product
Automatic Power Factor Controller
-
Power factor controlling based on the capacitor bank switching historyCapacitor is automatically disabled when it is deteriorated beyond a certain levelAutomatically learns the number of capacitors connected and the value.Capacitance-based power factor correction takes care of variation in voltage and frequency.Controlling based on VAR parameter and availability of built-in alarms Flexibility for site programmability of CT ratio suitable for any load
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
Product
One Channel Gas Controller
MX 16
-
Teledyne Gas & Flame Detection
Specially designed for applications in laboratory, storage, small boiler room, and breweries or battery charging rooms, the MX 16 measuring unit prevents the risks of explosion linked to the presence of toxic, anoxic and explosive gases in the ambiant air. Small size, ease of installation and use are the main strengths of the plant. Used with the OLCT 10N O₂ and CO₂ digital sensor series or any other O₂, CO₂, CH₄, GPL and H₂ analog sensor, the MX 16 guarantees you a solution that complies with French and European standards.
-
Product
Isolated PWM Controllers
-
Renesas' communications product portfolio includes a synchronizing pulse width modulating (PWM) current mode controller for subscriber line interface circuits (SLICs).
-
Product
Quality Control
-
Ensuring stream quality is essential for any business and should be secured with reliable technology. Boro solution is the right choice for QoS and QoE monitoring.
-
Product
Controllers
BKM91D
-
BK MIKRO BKM91, BKM91D, BKM91PN and BKM92KIO controllers utilize the premium version of firmware which allows for multiple tools or functions to be programmed. These controllers are typically used when advanced features are required such as checking for broken tool inside of a CNC tool changer or checking multiple object or free space positions.
-
Product
Fan Controller (24V / 48V version)
040-647
-
The Fan Controller (FanCon) is a platform independent system monitoring unit which monitors and if applicable controls the parameters, such as temperature and fan rotation speed, of a basic system.
-
Product
Control Valve Characteristics Trainer (ULP-23)
-
Unitech Scales And Measurements Pvt. Ltd
Control Valve trainer comprises of globe type control valve (½”) with diaphragm type Pneumatic actuator. The control valve is of linear / Equal% type. The setup comprises of water pump with necessary flexibal piping, Water tank, I to P converter, Air regulator fitted on a table top powder coated metal frame.
-
Product
Programmable Controllers
-
Panasonic Automotive & Industrial Systems Europe GmbH
The Panasonic product portfolio comprises both low-cost compact programmable controllers with little space requirement which are suitable for many basic tasks and high-end PLCs like the flagship FP7.A multitude of useful functions has been successfully integrated into the compact PLCs so that they offer many of the advantages of a modular high-end PLC such as analog control, network communication, and positioning control. All Panasonic PLCs offer an outstanding price-performance ratio.
-
Product
Control Driver
-
Citizen Chiba Precision Co., Ltd.
High functioning and compact driver for motors and actuators
-
Product
Electronic Speed Controller
AFI-ESC610
-
AFI-ESC610 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high voltage and high power motor application for electrical vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 6KW.
