-
Product
Solar Cell I-V Characterization System
VS6821
-
Industrial Vision Technology Pte Ltd.
This system provides cell manufactures and laboratories a new way in testing and measuring photovoltaic cells. Integrated with Steady-State Solar Simulator, it provides complete coverage of testing parameters and measurement requirements by most international standards. Its test methods, procedure & equipment are IEC 60904 compliant. Calibration of reference cell is performed at Fraunhofer ISE in Germany, and is traceable to PTB.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
Fully Automatic Solar Cell
Module Laminator-H
-
1. Model: BSL2236OAC-H2. Effective lamination area: 2200mm × 3600mm3. Dimensions: length 17410mm × width 3665mm × height 2164mm4. Heating method: heat conduction oil heating5. Compressed air source pressure: 0.6～0.8MPa6. Working vacuum degree: 100～40Pa7. Evacuation rate: 70L/S8. Temperature control accuracy: ±1.5°C9. Temperature control range: room temperature - 180°C10. Temperature uniformity: effective lamination area≤±2℃11. Lamination chamber height: 30mm12. Evacuation time: depending on the process, it is recommended to take 5 to 8 minutes13. Upper cover stroke: 300mm
-
Product
Four Channel Load Cell Tester
LCIC-4HS
-
Industrial Measurement Systems Ltd.
Four Channel Load Cell Interface Card Model LCIC-4HS The LCIC-4HS is a four channel load-cell interface board for the IBM PC/AT and compatible computers (ISA Bus). This board was especially designed to fit very fast and real-time weighing applications such as multi-head fillers. It supports up to four channels with one load-cell on each. All the necessary filters and the batching control functions are built on the board and are easily accessible by the user. Direct communication with the PC bus and high-frequency sampling enables the LCIC-4HS to handle all real-time applications and to achieve very high accuracy. The LCIC-4HS is memory-mapped. Up to 32 boards (128 channels) may be installed in a single PC. It comes with a detailed user manual and software utilities for easy installation and calibration as well as full examples for the programmer (including Win 95/98 drivers).
-
Product
HDDH-3932 Single Cell Battery Activator
-
HD Power Test Equipment Co.ltd
HDDH-3932 Cell Activator is used to discharge and charge and activate for disable single cell battery, which is simple, safe and accurate test device.The instrument is with perfect protection function, sound and light alarm and clear interface tips.
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Cell Production
-
JRT Photovoltaics GmbH & Co. KG
The production of lithium-ion cell batteries includes the three main process stages of electrode production, cell assembly and formation and aging. Automation is a critical factor for success, particularly in the process stage of cell assembly.
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Test Cell Controller
RAPID
-
The Rapid II Test Cell Controller is an integrated, multi-loop control and data acquisition system for test cell applications, designed to provide maximum performance at an affordable price. Rapid II combines the latest in digital control technology with off-the-shelf hardware to produce one of the industry's most powerful, flexible and advanced controllers at a cost-effective price. This high-speed, 4-channel PID controller includes ample I/O to act both as a system controller and a data acquisition system, reducing overall system cost and complexity. Designed for integrators, OEMs, and DIYers, these systems can be configured to fit your needs with little upfront costs and minimal risk while benefiting from a stable, powerful platform.
-
Product
SOLAR CELL TESTER
-
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
Product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
-
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
Product
Cross Flow Cell
-
Working electrodes for flow cell are mounted on blocks of PEEK. This resin protects the electrodes from external noise and allows researchers to utilize them regardless the content of mobile phase of HPLC because of their hard, organic solvent-resistance. Glassy carbon is usually chosen for the redox reaction study on liquid chromatography. Platinum, Gold, Carbon paste and Nickel electrodes are utilized for special purposes. Thin Layer Cell has been used as a electrode for research such as flow injection analysis (FIA) and the HPLC.
-
Product
Dual Fuel Gauge
1U432-series
-
The 1U432 dual fuel gauge is packaged as a compact, 3” instrument. It has dual D’Arsonval movements that are driven by two resistive bulb transducers in the fuel tanks. The two opposing pointers stand out sharply from the non-reflective black background.
-
Product
Voltammetry Cell
SVC-3
-
By using this cell, researchers can run experiments free from gasificationed steam. Also, researchers can get rid of influence of oxygen in the cell by bubbling nitrogen gas. This cell can be utilized with CS-3A Cell Stand. This feature is well suited for measurements of ultraweak current.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Battery Cell Insulation Tester
Chroma 11210
-
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
Product
Fuel Injection Tester
FIT13APB
-
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifoldIncludes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446)
-
-
Product
PXI Mixed Configuration Relay Module - 7 Cells Populated
40-138-AA-BB-CC-DD (7 CELL)
Relay
The 40-138 2A Relay Module with 7 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
Electric Vehicle Battery Cell Tester
MCV
-
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
Product
Single Point Aluminium Load Cell
EST-2
-
Technopark Automation & Control
The EST-2 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. This load cell is available in capacities from 3kg to 100kg.
-
Product
Bending Beam Load Cell
EST-7
-
Technopark Automation & Control
The EST-7 is a Bending Beam Load Cell suitable for use on lower capacity weigh hoppers, filling machines, packaging machines and conveyor belt scales. This load cell is available in capacities from 10 kg to 200 kg.
-
Product
Direct Burial Half Cell Reference Electrode
DB-A
-
Model DB-A Copper-Copper/Sulfate Reference Electrode designed for direct burial for long term monitoring of buried or earth contacting structures.
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
Pressure Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S Pressure Transducers manufactures a wide range of absolute and true gauge pressure transducers.*UNITECH’S Pressure Transducer is mainly a strain gauge based sensors ranging form Vacuum to 1200 Kg/cm2. *The stainless steel construction permits the transducers to operate in rugged, industrial environments. *We also undertake custom-built pressure transducer for specificrequirement and for OEM users.
-
Product
Test Cell Measurement
-
Accurate Technologies’ long history in powertrain development provided insight into the day-to-day issues that were occurring during engine testing at a time when electronic devices were being introduced to monitor performance instead of traditional mechanical means. Outside of the harsh physical environments, devices used in these applications need to perform difficult high-voltage signal conditioning and high-speed synchronous pulse processing. ATI developed unique products that satisfy specific test cell or dynamometer challenges. These highly accurate products measure engine timing (IGTM) or speed (SmartTach) in convenient ways to provide information that otherwise may not be available.
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
