Loop
See Also: Current Loops, HIL, Loop Testers
-
Product
Fast Temperature Shift
CherryTemp
-
CherryTemp is a temperature controller based on two independent Peltier channels, allowing for very accurate temperature control and ultra-fast shifts from 5°C to 45°C. A thermalization liquid circulates from a reservoir to the heat exchangers (heating/cooling Peltier elements) where it is thermalized to a target temperature. Once thermalized, this liquid can be quickly injected to a microfluidic device (CherryTemp chip) mounted near the sample. Because of the small thermal mass (the distance between the microfluidic chip and the sample), the temperature transfer is very fast (less than 10 seconds) and of unprecedented accuracy due to a feedback loop control of the room temperature and the heat-sink played by immersion objective lenses.
-
Product
dB Meter
-
The dB meter is used to determine the stability or fluctuations of the optical power over a large dynamic range with high accuracy and measurement speed. A fiber-coupled, power-stabilized 1.55µm laser diode is built into the device to enable simple and quick testing of passive fiber optic components or local fiber loops. Alternatively, light from external light sources in the wavelength range 780nm-1650nm can also be used.
-
Product
Three Loop Antenna
VVLA-30M
-
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard
, it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products. -
Product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
-
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
Product
Test Hardware
TTPSimulate XMC/PCIe
-
TTPSimulate is a high-performance test system which enables the simulation of a networked TTP system in real-time. It allows full hardware in the loop verification of a TTP unit. There are two form factors available for this product – PCIe and XMC card format. Both cards can act as four independent TTP nodes and have an IRIG-B interface for time-stamping.
-
Product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
Programmable Resistor Modules
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
Profile Controller With Data Logging
IM2756
-
Ajinkya Electronic Systems also manufactures profile controller data logging which is process controller for controlling process parameter against time. User can define the profile he wants with the help of extensive instruction set. Unit supports instructions like jump, loop, loop with count apart from ramp soak control. Relay On and Off instruction are supported.
-
Product
Industrial 4-20mA Driver
-
Analog Devices portfolio of leading industrial d/a converters and drivers addresses the challenges of enhancing system accuracy, reliability, and overall functionality while reducing form factor and power dissipation. The products provide a range of programmable output ranges from standard 4–20 mA for current loop communication to ±10 V for actuator control. They simplify industrial system design by offering considerable control functionality and advanced on-chip diagnostics to maximize system up time. ADI industrial converters also eliminate the need for costly calibration routines needed by some traditional discrete architectures.
-
Product
Probe Head
cViper
-
cViper™ is an ultra-fine pitch probe head for RF and high speed digital WLCSP. cViper is ideal for lab and large volume production test for precision analog, RF, sensors and mobility devices. Low loop inductance and high bandwidth up to 27 GHz, cViper offers low and stable contact resistance for singulated devices or wafer-level test. A variety of contact materials to optimize performance are available with device pitch down to 100 µm.
-
Product
Voltage Controlled Crystal Oscillators
VCXOS
-
Voltage Controlled Crystal Oscillators (VCXOs) are used for fine adjustment of the operating frequency and are normally used in conjunction with a phase locked loop.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Automatic Hysteresis Graph Test System
DX-4DMT
-
X-4DMT automatic hysteresigraph system accords with the standard permanent magnet test system, GB3217-92, used to measure the major and minor hysteresis loops, demagnetization curves, recoil hysteresis loops and initial magnetization curves in different temperature of ferrite, AlNiCo, SmCo, NdFeB and quenched material, and gives the magnetic parameter, Br, Hcb, Hcj, (BH)max, Hk and so on, and could meet different requirements on test function, precision, power capability, reliability, efficiency, price, local environment from laboratory to enterprise's production line.
-
Product
Multi-Axis Vibration Control
-
m+p VibControl provides coupled and uncoupled multi-axis vibration testing (MIMO) in a closed control loop. Test modes include random, sine, shock and time domain replication (road load simulation). Multi-axis motions are characteristic of field environments. The more a vibration test can replicate the field environment, the more realistically it can induce a vibration stress loading equivalent to that experienced by the product in the field.
-
Product
Signal Generator
SG-1501B
-
Features :*Programmable up to 110MHz stereo*100 types of programmable steps*Phase-locked loop digital synthesis generator*Output level -200dBu to 100dBu (in 1dB step)*7digit LED frequency display*With auto test function
-
Product
Wireless Device Functional Test Reference Solution
Functional Test
The Keysight S8890A Wireless Device Functional Test Reference Solution provides an automation environment which is both simple to use, yet comprehensive and powerful. Based on the Test Automation Platform www.keysight.com/find/TAP, S8890A provides optional instrument driver/plug-ins offering simplified logically grouped control steps. These steps can be sequenced, looped and swept to provide powerful individual test cases or comprehensive sequences. Each driver/plug-in is provided with extensive starter sample test cases which can be modified by Keysight or the end user the UE to be tested. Plug-in options:
-
Product
Pressure Calibrator
HPC40
-
AMETEK Sensors, Test & Calibration
The HPC40 Series handheld pressure calibrator is the world's first combined pressure and mA loop calibrator to be fully temperature compensated from -20 to 50°C. You can count on the same accuracy whether measuring pressure, current, voltage, or temperature.
-
Product
Dissolved Carbon Dioxide (DI-CO2) Ultrapure Water Delivery System
-
The DI-CO2 is used in single substrate cleaning tools for rinsing steps to prevent ESD effects and/or corrosion by creating UPW (ultrapure water) with precisely defined conductivity. It is a compact system for tool integration, providing conductive DI-CO2 water (Carbon Dioxide) with closed loop controlled conductivity. The conductivity is kept at a constant value under changing flow conditions by control of the CO2 concentration in the DI-CO2 water.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
CAN Interface
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
RGB to NTSC Video and S-Video Encoder
BL-ENC400B
-
The ENC400B is an RGB to NTSC video and S-Video encoder designed for industrial video applications. The ENC400B is especially useful for recording the signal from one of the new generation cameras that do not produce NTSC video or S-Video signals. The color subcarrier is locked to the horizontal frequency using advanced phase locked loop techniques. High signal bandwidth is maintained on both the composite and S-Video outputs. The sync signal can be applied as an external signal or can be present on the green channel.
-
Product
Main Effects
-
The Analog Multi FX is an Authentic Analog Multi Effects Pedal equipped with everything you need to get the job done on stage and in the studio. It’s got a Switchless Optical Wah, Distortion, Effects Loop, Stereo Chorus, and Echo. Even better these are reissues of classic Morley circuits leading all the back to the 1970’s. And speaking of the 70’s it also has a new finish that pays homage to the original chrome Morley pedals. It’s Heavy-Duty spun stainless steel that’s Built like a Tank and looks great under stage lights. Each one is hand spun at our Illinois facility.
-
Product
Elite™ 13.56 MHz RF Plasma Generators
-
The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.
-
Product
Passive Hydrogen Maser
VCH-1008
-
The VCH-1008 Passive Hydrogen Maser is a compact hydrogen maser with excellent frequency stability and utilises state-of-the-art technology. Full digital processing of the modulation and servo loop signals makes it ideal for high accuracy applications. An internal GPS/GLONASS option is available and provides automatic output signal frequency calibration.Key applications:- National Time Keeping Service- Space tracking and navigation- Verification of frequency signals - Scientific research
-
Product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
Programmable Resistor Modules
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
Analog Output Module
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Hydraulic Component Test Stand
Model 700
-
Model 700 Hydraulic Component Test Stand (HCTS). Designed to test heavy-duty, off-highway, closed or open loop pumps, the 700 gives you the capacity to confidently and efficiently verify the quality of your work. Test new or rebuilt pumps, motors, valves, and cylinders independently, and communicate their quality to your customers with the help of PowerNet TD, data acquisition software for transmission and hydraulic systems. Convenient work height with adjustable mounting track. 100, 200 or 300 HP drive motor options available. Variable Frequency Drive (VFD) controlled drive motor. 200 gallon (757 L) high-mount hydraulic oil reservoir for flooded pump supply. Combined kidney filtration and cooling loop for continuous cleaning. Thermostatically controlled cooler and 7 kW reservoir immersion heater.
-
Product
sbRIO-9239, Non-Enclosed, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780875-01
Voltage Input Module
Non-Enclosed, ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the sbRIO‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range. Non-enclosed modules are designed for OEM applications.
-
Product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
LIN Interface
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
Product
Ring-Loop TWTs
-
Communications & Power Industries
Small and lightweight products for pulsed radar and most advanced designs for commercial, electronic warfare and radar systems, the unique ring-loop slow-wave structure used in these CPI BMD traveling wave tubes provides high gain at kilowatt peak RF power levels without oscillation and achieve greater than 30% efficiency.
-
Product
CompactPCI
CPCI-ADDA
-
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.





























