-
Product
Fixture Building Software
FixGenius
-
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
Product
Exchangeable Test Fixture
2112/D/H/S-7/HG/Pylon
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 13,50 kg
-
Product
MMI-HV, Mechanical Test Fixture
100182
-
Mechanical test fixture with optimized ergonomics for function test, final test and ICT applications. The MMI is prepared for both safety switches with guard locking and electrical interlocking. Our test fixture is versatile.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
Open Source Hardware Test/Programming Fixture
OpenFixture
-
OpenFixture is a fully parametric programming/test fixturing solution written in openscad. The inputs are generated/captured from the users board layout software and a laser cuttable fixture is generated automagically.
-
Product
Test Fixture
OCP NIC 3.0
-
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
Product
Test Fixture Kits
-
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
Product
Tool, Solder Kit, Mini Coax with Solder Sleeve
910121144
Soldering Fixture
Used to solder Mini Coax Solder Sleeve contacts.
-
Product
Standard RF Fixture
-
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
Product
Automatic Fixture Removal
S93007B
-
The S93007B automatic fixture removal (AFR) is the easiest way to remove fixture effects from non-coaxial device measurements and runs on the PNA/PNA-L/PNA-X Series B model network analyzers
-
Product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
-
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials.
-
Product
Board Test Fixture Probes
-
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
Product
MEE-C, Electrically Driven Fixture
100846
-
MEE- C - electrically driven fixture for high actuating forces and high piece count production in the absence of a compressed air supply function and ICT test.
-
Product
LHS2-A, Single-Position Linear Arm Fixture
-
Single-position linear arm fixture, the LHS2-A. Your manual fixture for small assemblies with few needles for small series or laboratory set-ups. Small, extra compact and absolutely uncomplicated to operate.
-
Product
MMI-DVH, Mechanical Test Fixture
100360
-
Mechanical test fixture with optimised ergonomics for function tests, end tests and ICT applications. The MMI is prepared for safety switches with guard locking as well as for electrical interlocking. Our MMI-DVH test fixture is versatile and has a special cover height (internal cover dimension 114.5 mm). Reinforced version!
-
Product
Verification And Diagnostic Tools
Y1131A
Test Fixture
Provides module-specific tests to troubleshoot relay failures and predict maintenance requirements.
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
MMI-EV, Mechanical Test Fixture
100232
-
Mechanical test fixture with optimised ergonomics for function tests, end tests and ICT applications. The MMI is prepared for safety switches with guard locking as well as for electrical interlocking. Our MMI-EV test fixture is highly versatile.
-
Product
Stand-Alone Test Fixture
MA 2011/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1000Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 12,00 kg
-
Product
SMD Test Fixture
16034G
Test Fixture
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
Product
Test Fixture Kit
322109
-
Each kit comes with enough supplies to run 5 tests and we offer all materials separately if you ever need more. These kits can be purchased by themselves, with a furnace or with a test stand. If you have any questions about these fixtures please contact one of our testing experts to get more information.
-
Product
Food Grips and Fixtures
-
AMETEK Sensors, Test & Calibration
We supply material testing instruments to some of the world’s most innovative companies within the food industry. The reason for this is our extensive experience within food testing, combined with our high precision texture analysis and packaging test systems.
-
Product
MMIHF-B, Shielded Test Fixture
100223
-
Shielded test fixture for high frequency and radio application. Protection of the environment from the DUT or shielding of interfering influences on the test. With our high-frequency fixture MMIHF-B, you can test sensitive and transmitting assemblies - even those with a transmitter and receiver combination - in detail without risking consequences for your production.
-
Product
Stand-Alone Test Fixture
MA 2013/D/H
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 22,00 kg
-
Product
28 cm2 Test Fixture Operations Kit
-
The 28 cm2 Cell Test Manifold Kit offers a highly effective solution for testing of individual planar solid oxide fuel cells. The kit contains all items necessary to easily mount cells with ~100 cm2 substrates. Designed for both long and short term experiments to measure properties such as fuel utilization, thermal gradients, red-ox cycling and longevity/degradation, these kits will accelerate your research and development activities.
-
Product
Solid-State Battery Test Mold & Compression Fixture
SCF1
-
A precision-engineered three-electrode battery test cell designed for advanced solid-state battery research. It enables independent monitoring of the working, counter, and reference electrodes for accurate electrochemical analysis, interface characterization, and battery performance evaluation.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
Non-Destructive Resonant Inspection Drop Test Fixture
RAM-DROP
-
The Drop Test Fixture, Model RAM-DROP, Resonant Inspection System, allows automated sorting and quality testing of small metal injection molded (MIM), powder injection molded (PIM), additively manufactured, and other small parts by using the Resonant Acoustic Method (NDT-RAM).
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Test Fixture
Stopper kit includedYAVCANCON2 for fixture identification not included
