CompactPCI Chassis
A metal frame that serves as the structural support for a CompactPCI bus. (sbc.webopedia.com)
-
Product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
-
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
Product
4U cPCI Chassis
DP-cPCI-8118
-
DP-cPCI-8118 is a compact high performance 4U cPCI chassis. Complaint with the compactPCI specifications this provides the right platform options to meet small system integration needs. The chassis features modular construction and integrated cooling. The DP-cPCI-8118 is available with high-performance backplane and ATX power supply.
-
Product
LXI Chassis
-
Our LXI chassis allow any of our 3U PXI switch modules and many of our instrumentation modules to be controlled in an Ethernet environment. You may also be interested in our 2-Slot USB/LXI Chassis, this chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. Also our 4-Slot USB/LXI Chassis allow USB or Ethernet control of most PXI modules up to 4-slot width. For more information on these chassis, you can look in the bottom part of the table below.
-
Product
14-Slot Chassis
ATCA CO14G4 DC 14 Slot 14U
-
The new flagship AdvancedTCA® 14-slot chassis, DC version is Comtel’s “4th Generation” and the latest in high performance platforms for ATCA. Its modular design offers ultimate flexibility to provide a solution tailored for your needs.
-
Product
Shelf Manager Mezzanine Module (CompactPCI FW)
064-757
-
The Shelf Manager (ChMC) can be used to monitor the health of a system platform. With the ChMC it's possible to monitor voltages, temperature, fans, to control fans, GPIOs and I2C devices.
-
Product
RTD Measurement for CompactPCI
CPCI390
-
The CPCI390 has a 3U form factor and features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm limit checking. Sensordata is available in °C, °F, K and Ohm. All inputs are optically isolated from the system.
-
Product
ATCA 1 Slot Doubleheight Chassis
-
One slot AdvancedTCA® custom system supports a blade with double height to accommodate a custom blade for signal processing of the next generation cellular network application.
-
Product
Rack Mount Osprey Chassis 4-Slot Unibus
0249-U
-
10.5" high by 19" wide by 20" deep (267 x 483 x 508 mm), this chassis is FCC certifiable**. AT style motherboard, 3 x 5-1/4" bays, 2 x 3-1/2" bays. Cooling fans and space are included for user's hex-height, 4-slot DD-11 Unibus backplane, PC motherboard, diskette and hard drives (one hidden and four visible half-height bays).
-
Product
OpenVPX Chassis Platforms
-
With options for VITA 46/VITA 48 compliant specifications for VPX (with VITA 65 OpenVPX compliant backplanes), Pixus offers complete systems with power supply unit and backplane, fully assembled, pre-wired and tested. With a modular design approach, Pixus can offer virtually unlimited VPX chassis configurations for 3U and 6U boards. The VPX enclosures come in 1U-4U horizontal-mount (for 6U boards), 4U-5U vertical-mount (for 3U cards), and 7U, 9U, and higher chassis (for 6U OpenVPX boards).
-
Product
1U Rackmount Chassis
ACP-1010
-
1U Rackmount Chassis for ATX/uATX Motherboard with Dual SATA HDD Trays
-
Product
4-Slot USB/LXI Modular Chassis
60-105-001
Chassis
This 4-slot USB/LXI modular chassis offers a small lightweight form factor, making it ideal for portable, benchtop, and space restrictive applications. The chassis is designed for desk or rack mounting and features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
Product
Wallmount Chassis For ATX And Micro ATX Motherboards
AX60810
-
*Supports ATX/micro-ATX motherboard*Front-accessible one 5.25"HDD and two 3.5" HDD drive bays*Equipped with a PS/2 type power supply*One 12cm ball-bearing fan*Bidirectional mounting chassis*Easy removable filer*Flexible I/O opening on rear
-
Product
4U 14-slot Rackmount Chassis
AX6156LE
-
The AX6156LE is a 4U-high rackmount industrial computer chassis which can hold a 14-slot PCI/ISA backplane and supports ATX Motherboard form factor. One 12cm ball-bearing cooling fan maintains positive air circulation through the whole chassis. The front access I/O ports are designed for ease access and maintenance. Furthermore, this industrial chassis features three 5.25" and one 3.5" disk drive bays. A wide range of standard computing peripherals can be integrated with the chassis to meet different application requirements.
-
Product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
Enclosure
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
Product
6 All-Hybrid Slot 3U PXIe Chassis; AC Powered with Up to 8GB/s System Bandwidth
PXES-2301
Chassis
The ADLINK PXES-2301 compact 6-slot PXI Express chassis, compliant with PXI Express and cPCI Express specifications, provides one system slot with three expansion slots and five hybrid peripheral slots, supporting a wide variety of enhanced-bandwidth testing and measurement applications. The hybrid-slot design accepts installation of CompactPCI, PXI, CompactPCI Express, and PXI Express modules in any peripheral slot for maximum flexibility. Built on a four-link PXI Express chassis with 8GB/s system bandwidth, the PXES-2301's peripheral slots are all connected with PCIe gen2 x4, with slot bandwidth up to 2GB/s. The PXES-2301 implements a smart system monitoring controller, reporting full chassis status including fan speed, system voltages, and internal temperature.
-
Product
1100 HP Water Brake Chassis Dynamometer
CM-51
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
Product
CompactPCI & CompactPCI-X Bus Analyzer / Exerciser
CPCI850
-
The CPCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Modular Breakout System Chassis Mounting Frame
95-901-001
Mounting Frame
The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications. This low-cost system combines a BoB (Breakout Box) feature set with the added flexibility of an FIU (Fault Insertion Unit). By mating the FIU chassis directly to the BoB, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
Open Frame 6U 50HP Chassis
-
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
Product
3U CompactPCI Serial 2-Port CAN From PEAK Module
cPCI-A3CAN
cPCI Card
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x D-Sub CAN ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
Chassis
-
Highest channel densityUser exchangeable TRIONTM modulesfor analog, digital, counter, CAN inputsSelectable resolution 16 or 24 bit
-
Product
M-Module Carrier for CompactPCI (3U)
i3000
-
The i3000 M-module Carrier for CompactPCI features a 3U form factor CompactPCI gateway to the M-module interface. One M-module mounting socket is provided by this carrier. This carrier can be used in temperatures from -40°/+85°C. The M-module interface of the i3000 complies to the M-module Specification ANSI/VITA 12-1996. The interface features A8, A24, D16 and D32 access types.
-
Product
Stepper Motor Controller for CompactPCI
CPCI322
-
The CPCI322 is a 3U CompactPCI card. The CPCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
VME 19" Rack Mount Industrial Chassis
R2U4S
-
The R2U4S is a 2U height 19'' Rack Mount Industrial Chassis featuring 4 slots of either VME or cPCI 6U size boards. The R2U4S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications. All feature a door to better protect the electronics which is placed inside.
-
Product
3U CompactPCI 5-Port Serial Ethernet, Optional POE Card
cPCI-A3ETH
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP- 5x RJ-45 ports support up to 2.5G via Intel® i226IT Ethernet controllers- Optional PoE supported- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
Rack And Chassis Mount Products
-
PMI offers various RF and Microwave products that range from 250 kHz up to 40.0 GHz which are supplied in a ruggedized, 1U to 6U chassis. Many options are available.
-
Product
3U CompactPCI® Subsystem with 13-slot Backplane, 2 + 1 CompactPCI® Redundant Power Modules
cPCIS-2633 Series
Backplane
- 3U CompactPCI® backplane with 12 peripheral cand slots and one system slot- 2 + 1 hot swappable 500 W + 250 W CompactPCI® Power supply (supports three 250 W PSUs)- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5V, +3.3V, and +12V- PICMG® 2.11 47-pin power interface- Hot-swappable cooling fans & filter
-
Product
Embedded Chassis With Expansion Slots For Mini-ITX SBC
ECM300
-
*Designed for Mini-ITX SBC with expansion slots*One 3.5" or 2.5" HDD drive bay*2 PCIe or 1 PCIe x16 expansion slots supported*Slim design with 1 system fan*250W power supply supported*Easy and quick customization
-
Product
Chassis
-
United Electronic Industries, Inc.
Two independent Gigabit (1000/100/10Base-T) Ethernet InterfacesOne port for Control, the second for diagnostics orBoth ports bonded/teamed for redundant network accessCompact: 2.7" x 4" x 4.1"Over 60 different I/O configurationsRugged: 100 g shock, 5 g Vibration, −40 to +70 °C, 0 – 70,000 feetReal-time: 1000 I/O scans in < 1 millisecondInter-device sync interface
-
Product
Type 15, CompactPCI Serial, 5 Slots, SSL, 4U, 42HP, 294mm
047-425
-
CompactPCI Serial System Type 15 with 5 Slots: 4x CompactPCI-S.0. Peripheral Slots and 1x CompactPCI-S.0. System Slot on the left side of the system platform. 1x 300W pluggable, air-cooled mit fan fix-mounted and powder coated.
