Time
is an illusion of duration.
See Also: Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Timing, Counter / Timers, Atomic Clocks, Phase
-
Product
Full Wave Recorder
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
Product
PXIe-6366, 8 AI (16-Bit, 2 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
781057-01
Multifunction I/O
PXIe, 8 AI (16-Bit, 2 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module - The PXIe‑6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6366 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
-
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
Product
ESR Analyzer
LD-LESR-A11
-
ESR AnalyzerLD-LESR-A11is a portable unit with Westergren analysis method and infrared sensor measuring principle. It offers measurement range of 1 to 140 mm/h with throughput up to 80 samples/h. It has maximum 20 sample loading capacity at same time and two measuring time: 30 min or 60 min. Designed with touch screen large color display, built-in printer and RS232 interface. Used for analysis of erythrocyte sedimentation rate in hospitals, clinical laboratories and research.
-
Product
68-Channel Portable Logic Analyzer
16862A
Logic Analyzer
68 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
Product
Image Processing and Analysis Software
ENVI
-
L3Harris Geospatial Solutions, Inc
ENVI is the industry standard for image processing and analysis software. It is used by image analysts, GIS professionals and scientists to extract timely, reliable and accurate information from geospatial imagery. It is scientifically proven, easy to use and tightly integrated with Esri’s ArcGIS platform.ENVI has remained on the cutting edge of innovation for more than three decades due in part to its support of all types of data including multispectral, hyperspectral, thermal, LiDAR and SAR. ENVI makes deep learning accessible to people through intuitive tools and workflows that don’t require programming. ENVI geospatial image analysis can also be customized through an API and visual programming environment to meet specific project requirements.
-
Product
AC Line Splitter
1937
-
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
Product
Extended Version CODE300-32
-
Code300-32 Extended allows the running of two sessions of the program at the same time. This means that with two audio cards the system can handle up to 4 audio channels simultaneously: One could have two receivers, one into the Right (R) channel and the other into the Left (L) channel of the LINE IN input socket of the first audio card and the same configuration for the second audio card.
-
Product
DXN Portable Hybrid Ultrasonic Flow Meters
-
The Dynasonics DXN meter is a powerful tool for troubleshooting flow issues, whether you want to quickly verify the flow reading of another meter or to data log flow system values over an extended time period. The DXN portable meter has transducers that clamp onto the outside of the pipeno tapping or cutting is required. The meter can be easily moved and installed in different locations. The large color display makes it easy to read and the setup wizard walks you through the meter configuration steps.
-
Product
Martindale Abrasion and Pilling Tester
TF210
-
TESTEX Testing Equipment Systems Ltd.
Martindale Abrasion and Pilling Tester. To determine the abrasion and pilling resistance of all kinds of textile structures. Samples are rubbed against known abrasives at low pressures and in continuously changing directions. The amount of abrasion or pilling is compared against standard parameters.The unique design of our Martindale tester allows removal of individual sample holders for examination without lifting the top motion plate. It provides individual counters and parking function, interval time settable and a large touch-screen display. Standard sample holders and 9 and 12kpa Weights are included.Our Martindale Tester is available with 4, 6, 8 or 9 test positions.
-
Product
Hydraulic Vibration Testers
HV-Series
-
L.A.B.’s HV Hydraulic Vibration Test Systems help you design high quality, cost-effective products and shipping containers by accurately measuring sensitivity to vibration. HV Systems are specifically designed to meet a wide range of ASTM, DOT, ISTA, ISO and federal standards for vibration testing. HV Systems are ideal for a wide spectrum of testing applications ranging from sine sweep tests to the most complex data real time simulation, or random reproduction applications.
-
Product
Automated Multi-Functional Tester
QTouch 1408 C
Functional Test
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
Product
Temperature & Humidity Testers
-
Amprobe wireless temperature and humidity testers combine precise, accurate measurement of temperature and humidity with wireless communications up to 80 feet/25 meters to save time and steps. Measure and monitor temperature and relative humidity measurements over time using an Amprobe temperature and humidity data logger. These meters enable you to download measurements to your PC via an USB interface.
-
Product
Single Channel One Analyzer
MVNA-8-350-1
-
The upper half of the Central Unit is the Vector Receiver (VR) of the Analyzer, which can be a single channel one, model VR-8-350-1 (one millimeter wave signal detected at a time only)
-
Product
Time-Triggered Ethernet / ARINC 664 Part 7 (AFDX®) / IEEE 802.3 Ethernet Deterministic Communications
TE2
-
Module TE2 is one of NAI's latest generation of advanced function Configurable Open Systems Architecture™ (COSA®) compatible modules. The TE2 is a certifiable, single-port, tri-redundant, deterministic Ethernet communications interface module that supports TTTech’s certifiable TTEthernet® End System product consisting of three traffic classes: SAE AS6802 (Time-Triggered Ethernet), ARINC 664 Part 7 (Avionics Full-Duplex Switched Ethernet (AFDX®), and/or IEEE 802.3 best-effort protocol. By supporting all three traffic classes, NAI's TE2 is the ideal solution for current users of IEEE 802.3 Ethernet, who plan to upgrade to Deterministic Ethernet (ARINC 664 Part 7 (AFDX®) or Time-Triggered Ethernet SAE AS6802) protocols in the future at any time without changing hardware.
-
Product
Data Loggers
-
Record network data over time and/or based on location; standalone, wireless and remote capabilities available.
-
Product
Technology Insertion
-
Technology insertion allows customers to seamlessly integrate new, higher performance hardware technologies while retaining form, fit and function and application software compatibility.Over that time, application requirements change and grow – demanding greater computing horsepower. In recognition, we have put technology insertion at the heart of our product design, enabling our customers to leverage new levels of capability at lower cost and with minimal disruption.
-
Product
508XT - X-Tech Acquisition
-
The new generation 508XT system offers the most productive balance between real-time data and autonomous modes. While it never stops collecting data, 508XT offers the best quality with a reduced survey cycle time, and brings the highest production ever, in any environment.
-
Product
COTS Systems
System
Pre-integrated to save you time and money, pre-validated systems proved an optimum computing platform for mission applications.
-
Product
Break-Over Wrenches
MTBN
-
The MTBN is a preset production torque wrench with flexibility to adapt to different fastening applications as it is compatible with different head options. The unique break-over mechanism, provides an operator ample time to react once the target torque is reached and to stop applying any additional force to the fastener. Break-over torque wrenches improve control of the fastening process by reducing the risk of both over and under tightening.
-
Product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
-
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
Product
FPGA Boards
-
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
Product
AGREE Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood have 13 process and 5 times quality control to ensure the accurate control of all details for AGREE Test Chamber, EES and vibration test chamber, Temperature humidity and vibration test chamber, Comprehensive test chamber, Agree chamber
-
Product
3-Lambda Power Meter
3λ-PM
-
•Simultaneous wavelength detection and calibration.•B / E / G – PON 3 wavelength power meter and insertion loss tester (1310 / 1490 / 1550 nm)•Simultaneous measurement of 3-wavelength PON signals•Automatic wavelength detection to save time and cost•Rugged, shock and water-proof for field use•Compact, lightweight and cost-effective•Quick and easy to operate
-
Product
Super MUTT Deluxe Standard Edition
#9008-SE
-
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
Product
PXI-7842, Virtex-5 LX50 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module
780338-01
Multifunction Reconfigurable I/O
Virtex-5 LX50 FPGA, 200 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7842 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7842 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Rubber Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
Product
API testing suite
Postman
-
Postdot Technologies Pvt. Ltd.
Postman helps you be extremely efficient while working with APIs. With Postman, you can construct simple as well as complex requests quickly, save them for later use and analyze the responses sent by the API. Postman can dramatically cut down the time required to test and develop APIs. Postman adapts itself for individual developers, small teams or big organizations equally well.
-
Product
4ch Beam Forming Sound Source Visualization System
BF-3200/MI-5420A/BF-0310
-
Beam Forming is one of the sound visualization techniques that obtains the sound pressure distribution using the phase differece information from the sound source to the microphone, and makes it visualized with the color map.This technique requires a lot of microphones to cover a wide area and generally tends to increase the size of the system. By this Beam Forming system, Ono sokki achieved real time sound source visualization with just 4 microphones.
