Noise
a signal's fluctuation other than that desired.
See Also: Pink Noise, White Noise, RF Noise, Distortion, NVH
-
Product
Small Step Frequency Synthesizer
ZFR Series
-
ZFR series programmable frequency synthesizers combine multi-octave bandwidth, small step size, low phase noise, fast switching speed, and a compact package size to create a truly versatile synthesizer. The ZFR series can be tailored to the specific frequency range and control interface required, with programmable frequencies to 31 GHz.
-
Product
RF Milliwatt Meters
Type NDB-2 and NDB-3
-
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
Product
FPGA Mezzanine Card
FMC407
-
The FMC407 is a low noise clock generation and distribution module with eight clock outputs and eight trigger outputs that are fully synchronized.There are two configurations: 34.375MHz-200MHz or 34.375MHz-4.4GHz. The FMC407 is ideal for applications that require synchronous A/D or D/A sampling across multiple cards or systems.
-
Product
RF Synthesizers Modules
-
Holzworth Instrumentation, Inc.
Holzworth's RF Synthesizers Modules were originally designed as the internal, tunable LO test sources for Holzworth phase noise analyzer products. Due to the need for easy integration, the HSM Series designs incorporate a long list of electrical and mechanical features to satisfy the demanding requirements of today's high performance communications systems and integrated test systems. FIELD PROVEN RELIABLITY with MTBFs exceeding 240kHrs.
-
Product
Abnormal Noise Detection System In-Line Tester
MV-6000B
-
This product sets criteria found with waveform analysis software, and runs automatic judgment in-line.
-
Product
Master Oscillator Multiplexer
MOX Series
-
*Low phase noise OXCO *Interface between VSAT Modems and Frequency Converters *Robust housing is gasket sealed for weather resistance *OCXO iwth low G-sensitivity available *Single or dual multiplexer *Single or dual bias tee *Available in various OCXO frequencies: 10, 50, 100, 120 MHz
-
Product
Digital USB Sensor Interface AC,DC, IEPE
ROGADAQ2
-
The RogaDAQ2 USB DAQ is developed for highly accurate measurements in the T&M and also for NVH measurements. This USB Front End is optimized for noise and vibration measurements with 2 channel IEPE (ICP®) sensor supply.
-
Product
Phase Noise Analyzer
NXA-26
-
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Product
High Impedance Preamplifier
1671
-
The Model 1671 is a single ended low noise field effect transistor
-
Product
Precision DC Power Module, 50V, 3A, 100W
N6762A
Power Module
The Keysight N6762A is a 100 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. For leakage current or sleep-mode current measurements, add option 2UA for measurement capability down to 1 μA.
-
Product
Taper System, CCD Beam Imaging Camera
TaperCamD series
-
355 to 1150 nm, standard CCD detectorHyperCal Dynamic Noise and Baseline Correction software (Pat. Pending)CTE Comet Tail Elimination for > 900 nm (Pat. Pending)Port-powered USB 2.0; flexible 3 m cable, no power brick14-bit ADC, 4 MB image buffer & on-board microprocessorWindow-free sensors standard for no fringing25,000:1 electronic auto-shutter, 40 s to 1000 ms1,000:1 SNR (30/60 dB Optical/Electrical)
-
Product
High Power Narrow Linewidth Laser
AULLD series
-
Amonics' high power narrow linewidth laser (AULLD series) is integrated with Redfern Integrated Optics (RIO) PLANEXTM high performance external cavity laser. It features narrow linewidth, low phase noise, ultra low RIN, high output power with exceptionally reliable performance. The turnkey microprocessor controlled benchtop AULLD provides alarms and status indicators. An integrated RS232 or Ethernet computer interface provides easy control, diagnostic functions and data acquisition. It is particularly suitable for commercial fiber optic sensing applications, such as interferometric and Brillouin DTSS sensing systems for oil & gas, security, metrology and smart infrastructure.
-
Product
Sound Level Meter
831C SoundAdvisor
-
The SoundAdvisor Model 831C Sound Level Meter is designed to make noise measurement easy. Due to its color display, connectivity, extensive software features and small form factor the SoundAdvisor is an ideal choice for handheld operation. Attended measurements are simplified, with the ability to control and monitor data via any PC or mobile device with a standard web interface. Designed with the acoustic professional in mind, the SoundAdvisor offers an elegant solution for complex needs in an easy to use system.
-
Product
Computer Based Audio Component Test System
DATS V3
-
Rugged aluminum housing with detachable test leads and built-in precision calibration resistorTighter tolerances on internal components for more precise measurementsIncreased output capability means greater separation from the noise floor, resulting in more accurate measurementsDATS Linearity Test for comparing parameters and impedance plots at multiple drive levelsOptional under desk mounting brackets included to save desk spaceOnly 1" H x 2-1/2" W x 4-1/8" D for easy portability
-
Product
TX Ranger
4405200
-
The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.
-
Product
SOA Driver
S-109
-
SOA Driver slot module of FOTS system offers a special function that changes the amplification feature of input optical signal variously, by dynamically driving a built-in SOA module. This SOA Driver is an efficient module that can drive a high gain and low noise amplifier stably and modulate a high power amplified signal up to the rate of 155 Mbps. As a high power amplifier, this module drives the maximum amplified power of more than 10 dBm and has a stable broadband source characteristics of > 0 dBm. As a high-speed modulator of amplified signal combined with high current (400 mA) modulation technique, it outputs a high power and high bit rate amplified signal of > 155 Mbps with > 10 dBm peak power.
-
Product
Low Noise Amplifier
-
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
Product
sbRIO-9213, Non-Enclosed, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
781210-01
Temperature Input Module
Non-Enclosed, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The sbRIO-9213 is a high-density thermocouple input module that is designed for higher-channel-count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The sbRIO-9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The sbRIO-9213 features NIST-traceable calibration and a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
Product
Infiniium V-Series Oscilloscope: 25 GHz, 4 Analog Channels
DSAV254A
Oscilloscope
25 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
-
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
Xineos Large Area Detectors
-
As a leader in CMOS innovation, Teledyne DALSA developed the Xineos to deliver three times more sensitivity and five times more signal-to-noise performance than other standard technologies at equal X-ray dose conditions. CMOS image detectors offer numerous advantages including the ability to record smaller image details with higher resolutions – allowing for the diagnostics of medical anomalies at earlier stages, and significantly increasing the probability of early intervention, patient recovery, and reduced treatment costs.
-
Product
Ethernet/LXI digitzerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.448-20
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Gravity Sensors
iGRAV
-
Superconducting persistent currents (i) produce the most stable relative gravity meter in existence. Superconducting persistent currents (i) produce the most stable relative gravity meter in existence. Super stable: Drift less than 0.5 µGal/month Scale factor constant to better than 1 part in 104 for years! Super precise: 1 nanoGal (10-3 µGal) in frequency domain 0.05 µGal in the time domain for 1 minute averaging. Super low noise: 0.3 µGal/(Hz)½.
-
Product
CAT-5 Cable Equalizers
-
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
-
Product
sCMOS Camera
Dhyana 400DC
-
Fuzhou Tucsen Photonics Co.,Ltd
By combining their legendary color processing technology with the capabilities of the latest generation sCMOS sensors, Tucsen have created a paradigm shift in color camera performance.The launch of the Dhyana 400DC, thanks to its sensitivity, perfect color reproduction and impressive noise minimization, results in a new capability which has formerly been unavailable in the field of scientific imaging.
-
Product
Modular Raman Spectrometers
-
Multifunction confocal Raman microscopy system, based on new designed confocal microscopy techniques, with the ultra-low noise CCD camera latest advanced for Raman detection, highresolution spectrometer, attaining superior user friendliness and sensitivity.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.445-16
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Bump Tester
KD-163
-
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
Product
PXIe-4497, 204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module
781369-01
Analog Input Module
204.8 kS/s, 114 dB, 2 Gains, AC/DC-Coupled, 16-Analog Input PXI Sound and Vibration Module - The PXIe‑4497 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4497 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4497 delivers simultaneous sample on all channels. In addition, the module includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gain, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
