Test Access Points
network jump enabling undetectable data monitoring. Also known as: TAP
See Also: Network Monitoring, Network Taps, Aggregator Taps
-
Product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 6 Analog Buses
65-221-112
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
Function Test Fixtures
-
Modulized UUT BFT Test Fixture, Multilevel BFT Fixture, Over Clamp Test Fixture, Rack Mount Test Fixture, Self Contained Pogopin Test Fixture, Simple Low Cost PCBA Test Fixture, Tight Seal Required RF F/T Fixture, and more from IST Engineering
-
Product
Track-Signal Test Meter
Model TRSIG-1
-
Aplab Track-Signal Test Meter incorporates Digital Signal Processing based design to provide high accuracy and stability. It is designed for level measurement of selected frequencies. It also provides functionality of AC and DC voltage measurements.The purpose of Track-Signal Test Meter is to make adjustments, control measurements and inspections on both audio frequency track circuits of types FTGS 46, FTGS 917 and also for TI21M type track circuits (now known as BI track 300) for the measurement of eight frequencies from 5700Hz to 8500Hz for metro applications. Its compactness and battery operation render the unit particularly suitable for portable applications in maintenance and for level measurement in communication systems.
-
Product
Meter Test Benches
Test Station
-
The meter test station allows simultaneous testing of 3, 5, 10 or 20 induction or static electricity meters. The test station could be constructed for single-phase electricity meters or for three-phase meters.
-
Product
L4-7 Performance Testing
IxLoad
-
Keysight Network Applications and Security
Measure the quality of experience of real-time, business-critical applications with converged multiplay service emulations.
-
Product
Test Automation Software
-
PathWave test and measurement software delivers fast, accurate, and comprehensive data analysis. Connected workflows and trusted algorithms allow you to optimize test plans while increasing test efficiency. Designed for spectrum analyzers, oscilloscopes, network analyzers and many more test instruments as well as PCs or automation systems.
-
Product
Safety Testing
-
Whitelegg has over 80 years of experience in the design manufacture of market-leading electrical safety test equipment. Our unrivalled range of electrical test equipment serves a wide variety of safety testing and precision measurement applications for use in a variety of industries including manufacturing, construction, education, utilities, aerospace, calibration and anywhere else where there is a requirement for electrical safety testing or precision resistance measurement.Test equipment is cost effective, helps you to minimise expense, improve efficiency and increase profit. Whether you need electrical test equipment, environmental test, power analysers or HV Test Equipment, we stock the products to meet your demands, all backed by our first-class technical support if you have any problems using the equipment.
-
-
Product
UAT Test Management
-
User Acceptance Testing is the final stage of the Software Development Life Cycle, which is conducted by the users. User Acceptance Testing is extremely important to determine whether the project is working fine as per the end user's point of view. The UAT test management process has to be done in an organized manner to reap maximum benefits from the process.
-
Product
Functional Testing
-
Functional testing is a pivotal element for strengthening the quality of developed software. Functional testing basically refers to the black box testing that evaluate a particular IT product with reference to the functional requirements indicated with its specification. Functional test analysis process involves the testing activities which measure the code of each component to assure quality.
-
Product
Heat Detector Testing
Solo 423 / 424
-
Available in both 110 / 120 and 220 / 240 volt versions the Solo 423 and 424 are the professionals’ choice where cables and leads are acceptable. Unconstrained by energy availability they provide the quickest of test times and are, perhaps, most suitable for the highest temperature detectors.
-
Product
Axle Damping Test
MSD 3000 | VP 215033
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test stand MSD 3000 is characterized by a quick and precise physical check of the axle damping. The frequency-controlled plate excitation by means of electric motors determines the maximum oscillation amplitude and then evaluates the axle damping according to the principle of Lehr's damping. The fully automatic test sequence including the determination of the axle and vehicle weight enables a time-saving and reliable assessment of the axle damping.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Material Testing Software
TRAPEZIUM LITE X
-
Simple Software Enhances Productivity TRAPEZIUM LITE X is newly developed simple software for Autograph series testing machines. It boasts comprehensive new functions for more efficient testing.
-
-
Product
IAC Test Light
3501
-
Peaceful Thriving Enterprise Co Ltd
For GM1982 and newer GM TBI and PFI fuel infection system with square 4-pin connector. For GM vehicles with throttle body or port fuel injection systems, check the electronic control module signal that provides direction to the idle air control motor.
-
Product
Test Fixture and Test Programing
-
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
Product
Custom Bench Test
-
TestEdge provides customized bench test. If your device has specialized test requirements, it may be necessary to test your device using specialized bench equipment rather than traditional ATE. In other situations, both ATE and a custom bench setup may be required to fully characterize the device and provide necessary correlation. Finally, it may be useful to create a custom bench setup to facilitate device debug.
-
Product
Geomembranes Testing Equipment
-
Similar to roofing membranes, geomembranes can be tested using our Wet Roof Pro' leak detector kit or one of our dry roof leak detector kits, such as the PD30R or PD40R.
-
Product
CRPA Test System
-
The Spirent CRPA Test System is a development of Spirent’s GSS9000 Series platform for testing Controlled Reception Pattern Antenna (CRPA) systems with a separate RF output per antenna element. The CRPA Test System generates both GNSS and interference signals. Users can control multiple antenna elements. Null-steering and space/time adaptive CRPA testing are both supported by this comprehensive wavefront approach.
-
Product
Package Testing
-
Delserro Engineering Solutions
Package testing is performed to test the durability of packaged products in their shipping containers. Both the shipping container and the effectiveness of the packing are being tested. Typical specifications include ISTA, ASTM D999, ASTM D4169 and ASTM D4728.
-
Product
Cable-End Test Fixtures
-
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
Product
Triaxial Testing Machines
-
Triaxial testing machine for position-controlled triaxial tests with test cells 10-3150 ... Stand model in two-column design with electronic force transducer, flanged to the testing machine crosshead and adjustable electronic position transducer 50 mm. The machine is driven by a stepper motor with central spindle and pressure plate below.
-
Product
Optical Loss Testing
-
Is to inject a known level of light in one end and measure the level of light at the other end, using an OLTS. The difference between source and receive power levels is the loss.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Test Chambers
-
The left-hand axis scales the level of the 100 measurements and the right-hand axis displays the uncertainty to a statistical confidence level of 95%; proving the repeatability is better than +/-0.25dB between the measured values. Guaranteeing repeatability, accuracy and correlation across Lab’s, across Production lines and across the World
-
Product
Test Socket
-
Our test sockets are made for high performance and are of top quality, to guarantee a smooth, effortless process. We believe in providing our partners and customers with effective and intelligent solutions that they can apply with ease. Choose the solutions of TTS Group cater to the needs of detailed and complex systems.
-
Product
Automatic Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
Automated Test Equipment (ATE) adopts PID+PWM principle VRF (Refrigerant flow control) technology to realize low temperature and energy saving operation (servo control technology of refrigerant flow based on thermal condition of electronic expansion valve). Realize the automatic constant temperature of the studio.https://www.wewontech.com/automatic-test-equipment/
-
Product
Antenna Testing Services
-
Our chamber measures 28' x 14' x 14' with 12" to 36" pyramidal anechoic absorbers and is fully shielded using a dual layer metal enclosure. Our test chamber is designed to for frequencies ranging from .700 to 6.00 GHz.
-
Product
Environmental Testing Equipment
-
It is to do adaptability and properties test for materials under different environment conditions, which includes salt spray test to determine corrosion resistance and temperature and humidity chamber to do a variety of high-low temperature alternating test.
