VME Backplanes
-
product
Powered VME Crates
6U VME 195 Mini
The VME195 mini crate is the perfect choice for small setups with only a few VME modules. The crate offers 9 VME slots in a compact designed chassis with integrated low noise power supply and cooling fan. The mini crate can be used on the desk either as a desktop or up-right unit or be installed in a 19” rack.
-
product
VME Extender
VMEEJ1J2
VECTOR Electronics and Technology, Inc.
VMEEJ1 Extender on top & VMEEJ2 Extender on Bottomattached with mending plate to create VMEEJ1J2 Extender
-
product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB205
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
product
Pre-Configured VME Systems
Preconfigured VME systems are available in the 6U and 9U form factors and in a variety of chassis sizes, from 7 slots to 21 slots to fit varying price ranges and application needs. Each SKYsystem chassis has been tested for power and cooling requirements for the maximum number of processor boards. VME SKYchannel boards can be ordered as upgrades or additions to an existing SKYchannel System in order to increase processing capabilities for future requirements
-
product
Backplane Profiling & Inspection System
603d
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
product
System Synchronizer and Distribution Board - VME
Model 6891
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
product
+5 VDC to +3.3 VDC 75-Watt Converter 6U VME
44KS2
NAI’s 44KS2 is a 75-Watt DC/DC Converter that plugs directly into a standard 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +5 VDC input and converts it to a single +3.3 VDC output at 75 Watts. The 44KS2 is ideal for powering single board computers or any other devices that require +3.3 VDC.
-
product
VME Test Extender 3U/220mm Universal
110EXT3122-10xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
6-Channel VME Optical-to-Electrical Converter
V730
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
product
6 Channel 6 kV/300 µA VME HV Power Supply
V6521
The V6521 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 6kV, 300µA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available. The channels share a common floating return, which allows on-detector grounding reducing the noise level. HV outputs are delivered through SHV connectors.
-
product
64-Channel VME Digital Input/Output Module
V250
The V250 is a single-wide, 6U VME module that provides 64 non-isolated channels of digital input/output. Each 16-channel bank shares programmable pull-ups and input thresholds with a range of 0 to +10 volts.
-
product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
6U VME 1/10/40 Gigabit Ethernet Switch
ComEth4071e
The ComEth4071e is a cutting-edge 6U VME Layer 2/3 Ethernet switch compatible with VME 64x systems, complementing IC’s Ethernet switch product line including the ComEth4070e and the ComEth4000e.
-
product
8-Channel VME Delay Generator for Facility Timing Systems
V880
The V880 is a VME-based system timing module, used to distribute picosecond-precision timing pulses across physically distributed facilities. The V880 receives a 155.52 MHz (OC3 rate) fiberoptic master timing signal and outputs eight local triggers.
-
product
VME Test Extender 6U/220mm 64X w/o P0
116EXT6122-012XR
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Multi-Interface Test Backplane
SKU-047-01
The Multi-Interface Test Backplane was designed to support hardware and software designers who need to be able to plug in boards with different interfaces (into the host computer).
-
product
16-Channel VME Current Source & Analog Measurement Module
V460
The V460 is a VME-based versatile source/measurement unit. It includes a programmable constant-current source, a precision programmable gain 16-bit analog-to-digital converter, and a 4-wire, 16-channel analog multiplexer. An internal microprocessor supervises channel scanning according to user loaded parameters, reporting sensor voltage drops or, for selected sensor types, engineering-unit data.
-
product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
product
Passive Backplanes
Passive Backplanes series are easily customized which include PCI boards, ISA boards, PICMG 1.3 full-sized, PICMG 1.0 full-sized and half-sized single board computers. All backplane products provide with matching chassis and outstanding expansion flexibility.
-
product
VME PowerPC Single Board Computer
DP-VME-0669
The DP-VME-0450 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with Error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces the DP-VME-0450 allows the user to perform intensive I/O while permitting rigorous computing.
-
product
Other Backplane Architectures
Elma is well known for our backplanes based on common VITA and PICMG standards-based architectures such as VME, OpenVPX, and CompactPCI Serial. We also make backplanes for other architectures.
-
product
6-Channel VME Pulse Amplifier
V860
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
product
MIL-STD-1553 Eight-Channel VME Board
VME-8-1553
The V-Orchestra™ is an eight channel MIL-STD-1553B board which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 32K word of internal RAM.
-
product
VME64x VITA 1.7 Backplanes
Atrenne VME64x VITA 1.7 backplanes comply with ANSI/VITA 5.1, include a 12-layer low noise striplinedesign with outside layers, which incorporates a chassis ground EMI shield and are available in customer configurations.
























