SFP
is a multi-source agreement (MSA) transceiver used in communicaitons.
See Also: SFP Test, SFP+, Transceivers
-
Product
AdvancedTCA® Carrier Blade with 4x Intel® Xeon® Processor E3-1515M v5 COM Express Modules and FM10420 Multi-Host Controller
aTCA-9400
Processor Blade
- 4x COM Express Type 6 module slots supporting ADLINK Express-SL/SLE with Xeon® Processor E3-1515M v5 (45W)- Integrated Intel® GT4e GPU providing high-performance H.264/H.265 transcoding- COMe modules connected by Intel® Ethernet Multi-host Controller FM10420, supporting up to 25Gbps Ethernet bandwidth between CPUs- 2x 10G SFP+, 4x 1G RJ-45 Ethernet on front panel- 2x 10G to Fabric channels, 2x1G to Base channels
-
Product
Gigabit Ethernet
CWDM SFP Transceivers
-
CWDM transceiver modules are offered at wavelengths from 1470nm to 1610nm and include LC connectors. These SFPs are 100% compatible with Cisco equipment.
-
Product
Mini Media Converter
MX Series
-
The MX mini media converter provides one RJ45 10/100/1000Base-T connector supporting auto-negotiation, MDI/MDI-X, full-duplex and half-duplex. The other connector is a 1Gbps SFP slot, suitable for any 1Gbps SFP module.
-
Product
NI-7935, Xilinx Kintex-7 K410T FPGA, Controller for FlexRIO
783766-01
Controller
The NI‑7935 features a programmable FPGA and embedded processor optimized for deployment in the field for reliable, extended operation for applications requiring advanced I/O capability with embedded signal processing. It includes a Xilinx Kintex‑7 K410T FPGA, 2 GB of onboard DDR3 DRAM, a dual‐core ARM Cortex‑A9 processor running NI Linux Real‑Time, and 2 SFP+ ports for data streaming. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-DCE
-
Avionics Interface Technologies
Supports 10/100/1000 Mbit/s Full Duplex EthernetUtilizes SFPs to support both Copper and Optical interfacesUser controlled Ethernet frame transmissions with high precision timing and scheduling
-
Product
Avionics Interfaces & Test Instruments
ARINC 664
-
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
Product
Fiber Optic Connectors & Cages
-
Pulse Electronics Networking BU supplies high-quality fiber optic connectors and cages to innovative ODMs, OEMs and other manufacturers designing today’s most demanding network products. Our line of 40+ fiber optic connectors include SFP, SFP+, and QSFP connector and cage products.
-
Product
Quad SD-HD-3G SDI Multiviewer
DigiLink DLC910
-
The DLC910 adds full featured 4-Channel SD-HD-3G SDI multiviewer capabilities to the DigiLink media transport platform. Consuming a single slot in any DigiLink chassis, the DLC910 seamlessly integrates into the platform enabling users to monitor the status of up to 4 independent SD, HD, and 3G-SDI video and audio channels. A full featured multiviewer, the DLC910 includes format auto sense, audio monitoring with visual activity detectors, 16 character labels per quadrant, automatic aspect ratio, and quad or full screen displays. Wide options for inputs and outputs are available using external BNCs, optical or HDMI SFPs, or other modules in a chassis using DigiLink’s innovative integrated routing capabilities.
-
Product
Fiber Tranceivers
-
Wuhan Sunma Technology Co., Ltd.
Active Optical Cables, Fiber Optic Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP).
-
Product
ATCA Rear Transition Module
ART108
-
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
Product
Quickly & Accurately Validate Any Pluggable Transceiver from 10M to 100G
iOptics
-
iOptics offers a complete, powerful and easy-to-use tool for CFP and QSFP qualification and can validate the full range of low- to high-rate transceivers including SFP, SFP+, XFP, CFP, CFP2, CFP4, QSFP+ and QSFP28. iOptics offers a faster, streamlined and automated test sequence aimed at quickly and simply validating any type of 10M to 100G interface. It is the ideal solution for multirate field commissioning with a simple one-button pass/fail. It offers automated stress testing for lab qualification and is also ideally suited for data center and data center interconnect (DCI) testing.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
100Gbps Ethernet Packet Generators
-
Axtrinet (AXTRINET IS A TRADING NAME )
1x 100GbE QSFP28 port, 4x 25GbE SFP28 / 10GbE SFP+ / 1GbE SFP ports, Status Indicators
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
Product
Test Solution
Eye-BERT MicroX
-
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-time eye opening monitor and eye scanning capability can aid in troubleshooting by providing the operator with additional link quality information. Other features include Autonomous pattern detection, SFP diagnostic tools, and wavelength tuning (per transceiver capability). With a click of a button the Eye-BERT MicroX will automatically test an SFP module based on its advertised capabilities and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
Tools & Consumables
-
Tools & Consumables by Senko - SFP Check Light Tester, smart checker mpo tester 12 fiber, guide pin hole brush, smart checker VFL, insert-extract tools, and more
-
Product
Gigabit Ethernet
SFP Transceivers - Copper
-
Copper SFP transceiver modules (1000Base-T) are 100% compatible with Cisco equipment, include RJ-45 connector, and compliant with applicable industry standards.
-
Product
PXIe-8238, 10 Gigabit PXI Ethernet Interface Module
784976-01
Ethernet Interface
10 Gigabit PXI Ethernet Interface Module—The PXIe-8238 is a high-performance 10-Gigabit ethernet SFP+ interface for PXI Express based on the Intel 82599 10Gb ethernet controller. It includes two 10-Gigabit ethernet SFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
Simulator
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
Product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
100BASE-T1 SFP Module
Art.-Nr.: TE-1430
-
Convert between 100BASE-T1 and Standard Ethernet The 100BASE-T1 SFP Module is the optimum solution to convert between 100BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 100 Mbit/s full-duplex 100BASE-T1.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Pump Laser Diode Driver
S-110
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
Economical Solution for Test Requiring Fewer Instrumentation Modules.
OPTOWARE-S200 (FOTS-Bench Top Series)
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
Ethernet To Fiber Optic Converters (Point To Point)
-
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
PCIe Based FPGA Processing / Acceleration Card
-
iWave’s PCIe based FPGA Processing / Acceleration Card is a half-length PCIe x4 card featuring a high-performance user-configurable Xilinx® Kintex®-7 FPGA enhanced with high-speed memory and a high-throughput serial interface. Front I/O adds dual SFP ports, 1x HDMI1.4a IN, 1x HDMI1.4a OUT. All of these features combine to make the card ideal for a wide range of applications such as Edge Computing, ARINC818 Avionics Video Bus, Acceleration.
-
Product
Linear Equalizers
-
Macom Technology Solutions Holdings Inc.
MACOM offers high-performance linear equalizers for use in high speed copper connections for Ethernet, InfiniBand and Fibre Channel. The product line supports NRZ and PAM-4 multi-level signal connectivity and builds upon MACOM’s long-standing expertise in equalizers for broadcast video applications. The equalizers can support up to 112Gbps per lane data rates for 50 Gbps to 800 Gbps copper cable assemblies. In addition to copper cables, the linear equalizer can be used for wired backplane and on-board applications. Adding linear equalization to a passive copper cable can enable the same copper cable to carry higher data rates for longer distances. MACOM’s new linear equalizer product line can extend a typical copper cable’s performance to 7.5 meters at 56 Gbps and 5 meters at 112 Gbps data rates. Customers can consider active copper cables as an alternative to passive copper cables or active optical cables. Key benefits include low power consumption from a single 3.3V supply, low latency, hardware and microcontroller management modes. The products are suitable for SFP, QSFP, QSFP-DD and OSFP connector form factors.
-
Product
USB Multifunction Digital I/O Module
Model JI-4040
-
The JI-4040 module is a versatile, easy-to-use device for adding universal digital I/O capability to acomputer system via a USB connection. The module is comprised of 36 bidirectional I/O channels and 2 Special Function Ports (SFP). The SFP can be software programmed as a variable duty-cycle clock/pulse generator, event counter, or interval/pulse timer. The I/O is selectable to interface 5.0 V, 3.3 V, 2.5 V, or 1.8 V systems. Host to module isolation eliminates ground-loops and provides protection from noise and switching transients on external signals. The JI-4040 is available as either a desktop unit or low-cost OEM board.
-
Product
Fibre Channel XMC Interface Module
XMC-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
