Showing results: 301 - 315 of 356 items found.
-
85039B -
Keysight Technologies
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
783367-01 -
NI
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
783362-01 -
NI
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
GWRMT001 -
Grand Wing Servo-tech Co., Ltd.
◆To measure the Pulse Width transmitted by Transmitter for up to 9 channels. ◆To measure the Pulse Width sent from Receiver.◆To test the rotations of Servo automatically – at the pulse widths of top, medium and low points set by user already.◆To test the automatic rotations of Servo.◆To test the rotations of Servo by turning the knob on the tester manually .◆To test the sensitivity of Servo (1μS per step minimum).◆To measure RPM of a spinning propeller – for 2 – 6 blades ones, real time RPM value shown／to set the peak RPM value up to 99990 per minute.◆Shiny 4 digits red LED's to display the values measured.◆Power source can be from UM-4 / AAA cell x4, or an adapter with 7-15V or BEC (5V) from an ESC.◆An output port for applying Positive/Negative signals of Pulse Width from this tester.◆Four buttons for setting up functions and modes.
-
8200 -
Chroma ATE Inc.
Chroma Power Supply Auto Test System model 8200 provides complete solution for PC ATX power supply, adapter and battery charger testing. The application oriented system structure makes it the most cost effective test equipment for initial test in power supply production line. To meet the power supply test requirements, Chroma Power Supply Auto Test System model 8200 has built in 20 ready-made test items. Users can simply enter the test conditions and test the power supply features while proceeding. With the report and management functions, Chroma Power Supply Auto Test System model 8200 is able to provide versatile tools to establish test documents and perform system administration.
-
63000 -
Chroma Systems Solutions, Inc.
The 63000 series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power supplies, A/D power supplies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices.
-
Virginia Panel Corporation
Our customers have shared a long history of using printed circuit boards (PCB) in the interchangeable test adapters (ITAs) of their automated test equipment (ATE) stations. Whether you are designing a self-test fixture, looking to save space, improve signal integrity, or reduce cable management concerns, Virginia Panel Corpoation has a team of engineers to help you design, manufacture, and integrate PCBs into your ATE system.
-
Extech 380396 -
Extech Instruments Corporation
With the 380396 measure Insulation Resistance to 60GΩ with test voltages of 500V, 1000V, 2500V, and 5000V. Featuring polarization Index measurement (PI), Dielectric Absorption Ratio measurement (DAR), AC/DC Voltage measurement to 600V with Min/Max, Peak and Relative functions, and 1 to 15 minute timer function for IR measurements. Comes with test leads, eight C batteries, 220V AC adaptor, heavy duty carrying case, and user manual.
-
Extech 380395 -
Extech Instruments Corporation
With the 380395 measure Insulation Resistance to 60GΩ with test voltages of 500V, 1000V, 2500V, and 5000V. Featuring polarization Index measurement (PI), Dielectric Absorption Ratio measurement (DAR), AC/DC Voltage measurement to 600V with Min/Max, Peak and Relative functions, and 1 to 15 minute timer function for IR measurements. Comes with test leads, eight C batteries, 120V AC adaptor, heavy duty carrying case, and user manual.
-
ICT IDE and Sequencer -
Konrad Technologies GmbH
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly on a selected DUT- Debugging (single step)- Loop execution via sequences, or single steps- Optimization function with regard to waiting time and integration with Shmoo plot- detailed results output within tables as well as various results diagrams- Pin-Finder function to support adapter wiring- Automatic test program generation is available via Aster Testway
-
CV30P650 -
Frothingham Electronics Corporation
The CV30 P650 test station is currently the highest voltage pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. The CV30 P650 pulse adapter can produce a maximum current of 100A at up to 600V using exponential pulses up the 10/1000 waveform. The pulser is rated at 30KW from 300V to 650V. Voltage compliance at 100A is 600V. The station can also include all of the usual FEC200 tests in the same test program.
-
MLS-100 -
Notice
•Stabilized Light Source•1310nm & 1550nm•Very small and lightweight•Controlled by Smartphone or PC via USB or Bluetooth•Smartphone application software and PC software•Li-ion Polymer Rechargeable battery•Battery charging via a USB interface•Universal 2.5mm adapter to accept FC, SC or ST•Reference light source for optical test
-
RA 19 -
Kepco, Inc.
The 1U high rack adapter will mount four of the low profile 50W, 100W and 150W (Series HSF-1UR or HSF-1U) power supplies. Each plug-in power supply is equipped with a power on/off, indicator LEDs and voltage test points. The RA 19-1U provides access to the DIP switches and rack keying without disassembling the rack. It also provides a redundant scheme with modules 1 and 3 being powered from one a-c input and modules 2 and 4 from a second a-c input. Module numbering is left to right facing the front panel.
-
N1427B -
Keysight Technologies
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
23005 -
Norland Products, Inc.
The unique design of the splice accommodates either 125um or 140um fiber and any size buffer up to 900um. The precision made splice holder firmly holds the pigtail in position without causing stress on the fiber. The low viscosity index matching liquid has an indefinite shelf life and allows for an easy glide of the bare fiber into the splice. Within seconds, a fiber acceptance reading can be made with an OTDR or test set. Low loss with minimum back reflection can easily be achieved for more accurate signatures. Other applications for this kit: splice training aids, bare fiber adapters, and temporary splicing.
