-
Product
High Voltage Safe Measurement Systems
-
For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.
-
Product
Transmittance Dust Measuring Devices
-
Maintaining a clear sightline even when dust concentrations are highTransmittance dust measuring devices transmit light through the entire duct. With this type of measurement, light attenuation indicates the concentration of dust inside the duct. These measuring devices are specially designed for medium to high dust concentrations and large duct diameters. Consequently, they are equally suited to emission and process monitoring as they are to hall monitoring applications.
-
Product
12-Ch 10A RCV Power Distribution Unit
AR438
Switch Module
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
Product
Emergency Power Supply Units (EPSU) (14) 5-15R 1U/0U V/H
EPS-1415-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Coordinate Measuring Machines
-
Novacam's 3D Non-Contact Coordinate Measuring Machines are designed with versatility and superior performance in mind: Precision (better than 1um) Speed (1-30 thousand measurements per second) Simultaneous dimensional and surface inspection Smallest probes measuring 0.9mm in diameter Automation by teaching with joystick Portability
-
Product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
Laser Source
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
Product
Venturi Flow Measurement Trainer (UITM-22)
-
Unitech Scales And Measurements Pvt. Ltd
UNITECHS venturi flow measurement trainer comprises of an Venturi meter fitted between the piping. A small FHP pump is used to circulate the water through the piping. Pressure ports brought out from the Venturi meter are connected to a U tube mercury manometer to measure the pressure difference. Collecting tank of capacity 5 liter is provided with graduations to measure water level. Digital timer is fixed to calculate the flow rate. Flow can be controlled using a manual control valve. The complete setup is mounted on a table top model.
-
Product
4 10/100M LAN FTTH EPON ONU ( Optical Network Unit )
ONU-4FE
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ONU-4FE optical network unit (ONU), based Gigabit Ethernet Passive Optical Network FTTH EPON system user side equipment, combined EPON OLT (Optical Line Terminal) via a passive optical network PON, to achieve a multipoint (P2MP) high-speed data transmission. Provides powerful data, voice and video and other broadband services to users..
-
Product
Long Length Universal (ID/OD) Measuring Instruments
-
Pratt & Whitney Measurement Systems, Inc.
A simple software script allows automatic measurement of gages or custom parts for ultimate accuracy and ease of use.
-
Product
Total Flux Measurement Systems
-
LED’s and Luminaires must be characterized and tested for brightness and color, for production quality control and also for R&D. The Gamma Scientific Total Flux Measurement System combines our accurate Radoma Spectrometer and an integrating sphere for total flux (total power) and color measurements of LED, micro LED and Luminaires. Measurement parameters include spectrum, lumens, total power, peak and dominant wavelength, CRI, CCT, FWHM and other optical properties.
-
Product
Optical Displacement Measurement Systems
ODS Series
-
The optical displacement measurement systems of the ODS series are specially designed for measuring the ultrasonic vibration displacement at bond tools of wire & flip-chip die bonders. The systems are highly accurate and very easy to use. That makes it the perfect tool for displacement based calibration of ultrasonic bond machines.
-
Product
DC Power Source for Standard Lamp
DC502
-
DC502 is CONSTANT CURRENT DC POWER SUPPLY for standard lamp. Function and technical indexes are as follows: • output voltage 4 grades: 6V/12V/24V/50V • output current: DC 0~2.5A (adjustable) • Output current drift at full scale: ±0.05% reading value/10 mins • Monitor range of ampere meter: 0.0000A ~1.9500A, 1.950 A ~2.500A • Accuracy of ampere meter: ± (0.08% reading value + 0.02% full scale) • Max output power: 80W • Continuous working time: 8 hours • Work environment: Temperature 0℃ -25℃, humidity ≤ 85%R.H, supply source: AC220 ±10%, 50/60HZ • Holding conditions: -20~50℃ humidity < 75%R.H • Outside dimension (W×H×D): 333mm×114mm×307mm • Weight: about 8kg • Power: about 1000VA
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
M² Measurement Systems
-
Thorlabs' M2 Measurement Systems provide self-contained, turn-key solutions for measuring M2, divergence, focus diameter, waist position, Rayleigh length and other laser beam quality metrics. Pre-configured, factory-aligned systems covering wavelength ranges between 250 nm and 2700 nm are available. Choose from among systems that have a scanning-slit beam profiler, a camera beam profiler, or no beam profiler.
-
Product
Open Air Radar Level Measurement
-
Drexelbrook’s line of open air radar products offer superb resolution and accuracy for the demanding applications. This line of instruments features FMCW (Frequency Modulated Continuous Wave) technology to provide the strongest signal at the measurement surface providing the best return signals even with agitated liquids.
-
Product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
-
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
Product
Air Quality Measurement
-
Air pollution measurement is the process of collecting and measuring the components of air pollution, notably gases and particulates. The earliest devices used to measure pollution include rain gauges, Ringelmann charts for measuring smoke, and simple soot and dust collectors known as deposit gauges.
-
Product
Integrated Turbine Rotor Measurement and Assembly Platforms
GeoSpin
-
Rotary Precision Instruments UK Ltd
Improve productivity and achieve higher levels of quality by reducing inspection times and the need for costly teardowns due to inefficient rotor assembly.GeoSpin has been specifically developed for the measurement and assembly of smaller gas turbine rotors for the aerospace and power generation industries reducing the rate of teardowns by 95%.
-
Product
Trace Moisture and Dew-Point Measurement and Analysis
-
We offer a wide range of high-precision trace moisture analyzers, dew point meters, water dew-point transmitters, chilled mirror reference hygrometers and process moisture analyzers.
-
Product
Gas Measurement Device
Gascoseeker 2-500
-
Teledyne Gas & Flame Detection
Built on the success of the robust and reliable Gascoseeker MK2, the Gascoseeker 2-500 is the UK gas industry standard instrument for measuring % LEL and % volume flammable hydrocarbons, with over 20,000 instruments in use in the UK gas industry.The two-button operation means the Gascoseeker 2-500 is easy to use and operator training can be conducted quickly. The rugged design allows the Gascoseeker 2-500 to be used in harsh environments. The Gascoseeker 2-500 is also fully compatible with our range of calibration software and equipment.
-
Product
PXIe-4139, Benchtop Measurement Bundle with
865534-01
SMU Bundle
Benchtop Measurement Bundle with PXIe-1090, PXIe-4139
-
Product
Wi-Fi/Bluetooth/IoT Wireless Measurement Solution
MP5200
-
*One-to-four parallel high-speed non-signaling test*Support Wi-Fi 802.11ax latest standard*Support Bluetooth V1.x/V2.x/V3.x EDR/BLE V4.x/V5.1 measurement*Support IoT protocol NB-IoT, Zigbee, single-channel GNSS...etc
-
Product
PathWave IV Curve Measurement Software
PW9251A
-
The PW9251A PathWave IV Curve Measurement software helps to control Keysight SMUs for easy test setup and to perform IV measurements without any programming.
-
Product
Strain Measurements and Experimental Stress Analysis
-
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
Product
MP field sources calibration set
-
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
Product
Real-time S-Parameter And Power Measurement Uncertainty
S93015B
-
The S93015B provides real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on the same screen. It enables the users to estimate more reliable uncertainty and apply more realistic limit lines for pass/fail tests for better production yield rates.
-
Product
8-Slot USB 3.0 IDAQ Base Unit
iDAQ-938
-
USB 3.0 SuperSpeedWide range power inputLED status indicatorsPhysical ID switch for multiple module identification8 iDAQ slots2 programmable function pin for timing signal (trigger, clock) input/output
-
Product
Handheld Gauge for Nondestructive Coating Thickness Measurement
PHASCOPE PMP10
-
The most experienced device in our tactile portfolio – reliably solves all special applications.
-
Product
Real-time S-Parameter And Power Measurement Uncertainty
S95015B
-
The S95015B provides real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on one screen. It lets you estimate uncertainty reliably and apply more realistic limit lines for pass/fail tests for better production yield rates.
-
Product
NEXYGEN DF Force Measuring Software
-
The NEXYGEN DF software is an easy-to-use Windows based data analysis package for use with the digital force gauges and torque gauges. Your test results are presented in a spreadsheet format so you can analyse data and perform common mathematical and statistical calculations.
