ISO
International Standards Organization
-
Product
Overhung Pumps
-
Flowserve overhung pumps comply either with ISO, ASME or API standards. These pumps are available in different designs to meet the requirements for chemical, API, slurry and solids handling processes, as well as industrial processes. Different configurations guarantee reliable and efficient pumping processes. Numerous sizes, hydraulics and material combinations are particularly well suited for use in applications where uncompromising reliability and efficiency over a wide flow range are key.
-
Product
Fanless Embedded System With 7th/6th Gen Intel® Core™, Pentium® And Celeron® Processor For Railway And Vehicle PC
UST500-517-FL
-
The UST500-517-FL is powered by the LGA1151 socket 7th/6th generation Intel® Core™ and Pentium® processors up to 65W with the Intel® Q170 chipset. The integrated 16 PoE ports are available in RJ-45 or M12 connectors for IP cameras. It provides a full scope of power protection that includes intelligent vehicle power management technology for ACC on/off delay, shutdown delay, and over/under voltage protection. Enhanced by its robust structure and system design, the UST500-517-FL is able to operate under a wide temperature range from -40°C to +70°C and vibration endurance up to 3 Grms. This transportation embedded box is in compliance with ISO 7637-2 and EN 50155 for mobile surveillance applications. There are 16 Gigabit LAN ports which support 802.3at/af Power over Ethernet with a total power budget of 200W. Its DVI-D, HDMI and VGA interfaces support three surveillance monitors. Furthermore, its external accessible SIM card slot enables users to easily change SIM card for different telecommunication service. With wireless LAN modules, this user-friendly transportation embedded system can real-time transmits the video to the control center. The two built-in or four swappable SATA hard drives are used for mass storage of video files.
-
Product
In-depth Execution Time Analysis For Critical Software
RapiTime
-
*Timing analysis (inc. WCET) for Ada, C & C++ on-target & host**Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Produce evidence for DO-178 and ISO 26262 certification
-
Product
Mobile Testing Center
MTC-1500
-
The Mobile Testing Center (MTC) is a preassembled, above ground, mobile, testing solution designed for outdoor testing applications. An affordable option to permanent Test Cells, the MTC is comprised of 2 ISO containers. Container 1 includes a Test Cell and heated and air-conditioned Control Room. Container 2 is optional and includes facility support equipment: Bulk Fuel Storage, Pneumatic System, Water Recirculation System (WRS), etc.
-
Product
Quick Change Molds
-
The AIM Quick Change Mold, used within the polymer industry, was introduced by Axxicon in 1989. It is a flexible test mold system designed to comply exactly with the internationally accepted ASTM and ISO standards which are also used by CAMPUS® — the plastics database.
-
Product
Unit Testing & Mocking Solution for .NET
Isolate
-
Part of Typemock Isolator,The Complete Unit Testing & Mocking Solution for .NET From mocking to coverage to automated test suggestions
-
Product
Energizer
ISOTTA
-
Essentially made up of a stainless steel cylindrical body of tubular shape, the energizer has a front section that may be unscrewed (cartridge chamber), apt to contain an 8-bore blank cartridge, or industrial type (easily found in every gun shop). This cartridge chamber is without barrel, thus permitting the axial ejection of the energy wave, caused by the explosion of the cartridge, generating waves of type 'p' (longitudinal) and type 's' (transversal).
-
Product
Calibration Equipment
-
Calibration is the method of comparing tools and measuring devices to higher accuracy standards. Torque calibration equipment is the official means by which torque testers and sensors are calibrated and are traceable to National or International Standards, such as N.I.S.T and ISO. In order to maintain precision accuracy, it is essential that torque measuring equipment be calibrated regularly. By equipping your team with Mountz calibration equipment, you can avoid the costly chore of sending your torque tools to the lab whenever they fall out of alignment.
-
-
Product
Compiler Test & Validation Suite
SuperTest
-
SuperTest is the test and validation suite for C and C++ compilers that has tracked the (ISO) language specifications for more than 30 years. It is a complete validation environment with: A huge library of hand-written test, A large body of generated tests, A framework to easily set-up and run compiler validations.
-
Product
Safety Command Devices
-
Leuze electronic GmbH + Co. KG
For stopping in emergencies, EN ISO 12100‑1 stipulates protective devices and supplementary measures such as E‑Stop buttons or emergency rope switches. The E‑Stop buttons are used wherever it makes sense to be able to enter a stop command at a specific location. E-Stop rope switches are used for larger danger zones.
-
Product
Precise Measurement of Airborne Noise Insulation
Isokell
-
Isokell offers a flexible method geared specifically to the needs of the automotive industry for measuring airborne noise insulation and the transmission loss of vehicle components. The system is easier to use and less costly than traditional acoustic measurement systems.
-
Product
Smart Card Testers
CT1000
-
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
Product
COM-HPC Server Type Size E Reference Development Platform based on Ampere® Altra® SoC
Ampere Altra Developer Platform
Software Development Kit
Backed by a broad Arm® ecosystem with an Ampere® Altra® SoC at its core, using the Arm® Neoverse™ N1 platform, the Ampere Altra Developer Platform provides premium performance from a cloud-to-edge infrastructure, keeps an extremely low thermal envelope, lower TCO, and significantly lower power consumption than x86 designs. It supports the open source EDKII as bootloader with UEFI, so customers can just download a stock AArch64 (arm64) ISO such as Ubuntu and install it through booting a live ISO directly on the target. The same convenience we have become used to by using x86 / amd64 target systems.
-
Product
Tensile Strength Machine
UI-1100
-
Tensile Strength Machine, also known as Tensile Strength Tester, Universal Testing Machine (UTM), is used to do tensile, peel, shear, bend, and other tests of materials. Universal Testing Machine can do plenty tests like sole/upper bond test ISO 20344, velcro strength test (peel and shear strength) ISO 22776,zipper strength test ASTM D2061, rubber tensile test, 3 point bending test and etc.
-
Product
Side Channel
-
Flowserve side channel pumps comply with ISO standards. They cover bare shaft, compact and inline designs. They fully satisfy the high operational safety standards of the process industry. Their self-priming and gas-handling characteristics guarantee safe operation, even in case of evaporation.
-
Product
PMC Module
PMC-CIV-COM-ISO
PMC Module
User Programmable AlteraCyclone IV FPGA 484 BGA:• Stand alone possibility• Single wide PMC Module• 20 LVDS,2 RS-422,1 RS-232• Optional User clock oscillator
-
Product
CAN FD/CXPI Communications Expansion Kit
OP-SB87FD
-
OP-SB87FD is an expansion board for LE-8200A/LE-8200 used for monitor/simulation of CAN (ISO 11898-1), CAN FD (ISO11898-1:2015), and CXPI (JASO D015). With this kit and the line state sheet, LE-8200A/LE-8200 works as a stand-alone type analzyer for CAN, CAN FD, and CXPI. The board supports development of CAN (used for automotive industry and other industries), CAN FD (next-generation standard of CAN providing more high-speed and communication capacity), and CXPI (invented in Japan to replace direct wirings) devices.
-
Product
High Voltage Optically Isolated Probe, 1 GHz Bandwidth. Includes soft-carrying case.
DL10-ISO
-
The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.
-
Product
Rectal Probe For Rats (Isolated)
RET-2 ISO
-
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - '' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds.
-
Product
Horizontal Flammability Tester
TF311
-
TESTEX Testing Equipment Systems Ltd.
Horizontal Flammability Tester, to determine the comparative burn rates and burn resistance of textiles, particularly those for automotive interior use. Horizontal flammability tester is safe and easy to operate, Comprises draft free stainless steel cabinet with observation window, sample holder and door mounted burner. Horizontal Flammability Tester complies with ISO 3795, ASTM D5132,FMVSS 302, etc.
-
Product
Rectal Probe For Mice (Isolated)
RET-3 ISO
-
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds.
-
Product
PCI Express Mini Card
mPCIe-UCAN2 & mPCIe-UCAN2-ISO
-
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
Product
Labratory Micro-Spot XRD Residual Stress Analysus with both Iso- and Side-Inclination Methods
AutoMATE II
-
Residual stress may be created during the manufacturing process of a material, or it may accumulate in a structure over many years in operation. In either case, this stress can have a serious negative effect on a product's quality, durability and lifetime. Accurate detection of residual stress is an important element of the quality control process and helps predict the service lifetime of products.
-
Product
CorSense™ Environmental IoT Sensors
-
Our line of CorSense™ wireless sensors are capable of monitoring air quality, humidity, barometric pressure, temperature, current, vibration, and more.Built with a rugged case and able to withstand harsh industrial environments, these sensors are all tested to ISO standards. When paired with CorGateway, sensors gather and transmit data securely to a Corvalent CorEdge computer anywhere from 2 to 28 miles away.Extremely energy efficient, CorSense IoT sensors can also run on batteries for up to 2 years.9 different sensor options:-Smart Vibration & Temperature Sensor -CO2, Temperature, Humidity & Particulate Matter Sensor -CO2, Temperature & Humidity Sensor -Temperature, Humidity, Pressure & Air Quality Environmental Sensor -Precision Pressure Bidirectional Differential Sensor -Pressure Bidirectional Differential Sensor -AC Current Monitor -Vibration & Temperature Sensor -Predictive Maintenance Module Sensor
-
Product
Multichamber PECVD/Etch System
IsoLok 5000
-
Load locked cluster toolCassette to cassette processingUp to 4 coatings can be deposited without breaking vacuumSubstrate sizes: 125 x 125mm,156 x 156mm and200mm dia. (smaller sizes can be processedusing a carrier)Typical coatings: SiOx & SiNx - doped & undoped & a- SiR&D, Pilot production and production capabilitiesRIE chambers availableFull computer controlProcess chamber is modular and interfaced with 200mm slot valve
-
Product
Stable Isotope Ratio Mass Spectrometer
isoprime precisION (IRMS)
-
Elementar Analysensysteme GmbH
Stable isotope analysis provides great insight into diverse applications and delivers a greater understanding of the micro and macro cycling mechanisms of the organic elements through the world around us. Though our collective knowledge continues to grow, so does our desire to explore further. The more we know, the more we question.
-
Product
SRA01-Albedometer
-
Hukseflux Thermal Sensors B.V.
SRA01 albedometer is an instrument that measures the solar albedo, or solar reflectance, and net solar radiation. It is composed of two second class pyranometers with thermopile sensors, the upper one measuring global radiation, the lower one measuring reflected solar radiation. It complies with the latest ISO and WMO standards. SRA01 can be connected directly to commonly used datalogging systems.
-
Product
Magnetic Stripe Test Cards
-
Test Limit Cards (and tickets) are nominally encoded to ISO standards BUT WITH specific parameters deliberately set to predetermined levels, which can be inside or outside the ISO limits. The Test Limit Cards are designed for use by Test\Inspection Departments, Field Service Engineers, Reader \ Encoder Development Engineers to check and confirm proper operation of magnetic stripe reading equipment (e.g. ATMs and POS).
-
Product
Test Targets & Charts
-
APPLIED IMAGE is a world leader in the field of IMAGE EVALUATION Test Targets and Test Charts. Some of the specialized test charts include camera image evaluation ISO, NIST, ANSI, and MIL standard image evaluation applications; photonic and optophotonic applications; test charts for copiers and scanner; DATAcapture and BARcode Scanning testing; Security & Identification Image Capture; and all other type of imaging industries that require quality evaluation of thier image capture systems.
