Injectors
Introduce known values.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
PoE Injectors, Splitters and Extenders
-
Advantech's fiber & PoE converters, injectors, splitters, and extenders are designed to provide network operators support for Mega PoE IEEE 802.3BT
-
Product
Engine Controller
FireLynx
-
The fully programmable FireLynx control module is used for Engine Development, Test and Control as well as directing the real time operation of Fuel Injector Test Stands.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
PRO Test Lead Kit
142
-
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
Product
DC Bias Injector
J2130A
-
When using the network analyzer to measure impedance, such as the capacitance and ESR or a capacitor, or the DCR of an inductor, etc., it is often necessary to provide a voltage bias to the device being tested. This is true of semiconductor junction capacitances, varactors, and some ceramic capacitors (especially X5R). In these cases the impedance is a function of the DC bias on the device. The Picotest DC bias injector (J2130A) is used for this purpose during impedance measurements.
-
Product
Low Current Probe 80A
695
-
Great tool for accurate measurement of low current. Use with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works very well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. In addition, the clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.
-
Product
Professional Automotive DMM
590
-
Another good choice for the professional automotive technician, the #590 puts the right cababilies in your hands. For example, the #590 can test the on-time of fuel injectors using the Ms pulse width test function. This DMM is completely auto-ranging, making it an easy and efficient tool to use. The #590 includes two sets of test leads, RPM pick-up, temperature probe, 9 volt battery, instructions manual and carrying case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
Product
EFI Test Light-GM SCPI
3414
-
Peaceful Thriving Enterprise Co Ltd
*Simply for testing: Disconnect the fuel injectors, plug in a Noid.*Quickly determines if the electrical signal present at the fuel injectors.*Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
Product
Fiber Optic Measurement Systems & Sensors
-
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
Product
Automotive Test Lead Kit
143
-
Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
-
Product
Injector Expert
InEx-2
-
Injector Expert InEx-2 is a versatile tool for advanced diagnosis of Common Rail injectors. It enables electrical and mechanical testing of injector actuators – solenoids and piezoelectric stacks. Its feature to generate injector control signal may be used for testing injector performance on a test bench. Technical capabilities of InEx-2 allow the following tests:
-
Product
UNIVERSAL NOID LIGHT
27800
-
Tests throttle body injectors, ported fuel injectors and sequential central port injectors, Adjustable probe fits all electronic fuel injection systems and swivels to fit various widths, Flashing light indicates normal pulses, no light indicates a problem.
-
Product
Automotive Fuse Current Probe
FUSE PEEKER
-
Automotive Diagnostics and Publishing
Automotive Fuse Peeker Current Probe for Testing Injectors, Coils, Solenoids and most components. The FUSE PEEKER Automotive Fuse Current Probe works with your own scope, the Auto Scope 1 or any other type of oscilloscope. It uses magnetic sensor technology, which is accurate and safe for your tool. It can detect small amounts of current as small as 5 milli-amps.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
Product
Low Temperature Gas Source
-
Get a low-cost means to introduce a gas without thermal pre-cracking using Veeco’s low-temperature gas source for molecular beam epitaxy (MBE) systems. The source features a large conductance tube for fast gas switching and a diffuser end plate for good growth uniformity. It is an ideal gas injector for CBr4 for carbon doping in GaAs and NH3 for GaN growth, as well as any other gases that do not require thermal pre-cracking. Enhance system capabilities further by combining the source on one mounting flange with an Atomic Hydrogen Source or 5cc Dopant Source.
-
Product
Injector Tester
7620
-
Peaceful Thriving Enterprise Co Ltd
By connecting with the 12V vehicle battery, the tester generates four different output signal pulses for user to check the condition of the injector. By using the tester, user can check if the injector is clogged, leaking or blasting.
-
Product
Automotive Tester
-
An automotive tester can be used to inspect one or more aspects of an automobile. For example, a borescope automotive tester is an automotive inspection camera used by auto body mechanics to see inside car, truck and other vehicle engines before removing any engine parts. Other kinds of automotive tester devices are used to adjust belt tension, test the electronic ignition starter, search for air conditioning leaks, measure the force required to press a brake pedal, determine the antifreeze concentration, or check the paint thickness over collision repairs.PCE Instruments (PCE) offers a wide variety of automotive tester products. These diagnostic support tools help professional automobile mechanics identify a number of vehicle repair needs. PCE's automotive tester products can aid in the diagnosis of many different mechanical and electrical system issues, including but not limited to locating the cause of an engine misfire, testing fuel injector resistance, pinpointing an engine coolant leak, or detecting car cylinder head problems. It's no wonder so many auto repair technicians choose to stock theirs shops and garages with PCE automotive tester products.
-
Product
EFI Test Light-Bosch 2
3416
-
Peaceful Thriving Enterprise Co Ltd
Simply for testing: Disconnect the fuel injectors, plug in a Noid. Quickly determines if the electrical signal present at the fuel injectors. Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
Product
FUEL INJECTOR CANISTER CLEANER
FIT470B
-
*Cleans carbon from intake valves, fuel passages and cylinders with a professional carbon cleaning solution*Will restore the original spray pattern more effectively, giving improved performance, fuel economy and emission tests*Uses shop air with any professional canister cleaning solution on the market
-
Product
Solid State Current Injector
J2111A
-
The current injector is one of the most versatile of the injector products. Coupled with the G5100A, or other equivalent function generator, it is capable of performing small signal load steps up to 40MHz, with very fast rising and falling edges. Using the G5100A, also allows the rise and fall times to be controlled, various waveforms or even arbitrary waveforms. This can be used to simulate the effects of many different types of loads, including high speed digital circuit loading, which is often largely dynamic.
-
Product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
Analyzer
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.
-
Product
GC Autosampler
L-PAL3
-
Increase your lab productivity with LECO's exclusive L-PAL3 autosampler for our GC instrumentation. It offers increased vial capacity, discrimination-free GC injections (ultrafast injections), an automatic tool exchange to switch between injector types (liquid, headspace, or SPME), minimized carryover, and the sensing of vial bottoms to avoid mis-injections. All of these advantages come on a highly robust and industry-proven platform. The LECO L-PAL3 GC autosampler allows you to safely focus on your samples and find what else could be in them, rather than experiencing downtime and uncertainty in your lab.
-
Product
Connector and Breakout Box
ES4640
-
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
Product
Common Rail Injector Tester
ICR-4 Tester
-
ICR-4 tester is used to control electromagnetic and piezoelectric injectors used in the common rail injection systems. It is possible to control up to four injectors of a type at a time. The signal generated by the tester which controls the injectors, corresponds to the signal which appears in the car engine controller.
-
Product
Natural Gas Analysis
-
Recently, natural gas has been recognized as a clean resournce for energy, in addition to being a raw material for chemical products. Recently a cutting-edge drilling technology has increased the use of shale gas. As the production area diversifies, the need for gas composition analysis has increased. Shimadzu addresses analytical requests with a wide system GC lineup. For analysis of liquified gas, such as LPG, a dedicated injector with a vaporizer is available. Both manual injection and online injection are available. The operation software can automatically calculate needed values, such as indexes, calorific values, etc.
-
Product
Premium Automotive DMM
597
-
*CATIII 1000 Volt / CATIV 600 Volt Approved & Safety Rated *Safe For Use on Hybrids and EV's *Highest Quality Auto-Ranging DMM Designed for Automotive Trouble Shooting *18 Test Functions, 48 Test Ranges *Peak Min/Max records transient voltages as fast as 1 millisecond *Min/Max Mode records variations in all functions *Also measures Temperature via Temp Probe in Both F and C *Milliseconds Pulse Width Measures Fuel Injector ON-TIME *Inductive RPM Readings for both DIS and Conventional Ignitions *Desirable 20 Amp Test Range - Dual Fuse Protection *Modern Design, the Protective Holster is Built Into the Housing *Data Hold, Auto Power-Off, + Trigger Adjust *Large LCD Display w/White LED Backlighting and 40 Segment Analog Bargraph *Blow Mold Case, Test Leads, K-Type Temp Probe, Inductive RPM Clamp and Instructions included *Waterproof to IP67 Standards
-
Product
Advanced Seismic Source
GI-SOURCE
-
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
Product
POWER PROBE 4
PP401
-
*Electronic circuit and component tester that supplies battery ground and power along with 8 diagnostic testing modes to provide automotive technicians with detailed information on the circuits and signals being tested*Diagnostic Modes include: AC/DC Voltmeter, Ohmmeter, Frequency, Pulse width (Positive and Negative) Fuel Injector Tester, PCM/ECM Driver Tester and PPECT3000 Signal tracer*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)
-
Product
PSE Conformance Test Suites
-
Whether testing single port injectors or 48 port PSE’s, Sifos offers the ultimate solution to assess PSE conformance to all applicable IEEE specifications. With the click of a button, fully automated testing and reporting delivers comprehensive and informative results including difficult-to-spot intermittent conformance behaviors. Available to PSA-3000 and PSA-3402 PSE test instruments.
