-
product
Deep Ultraviolet Spectrophotometer System
VUVAS-10X
A new ultraviolet spectrophotometer system for optical metrology just arrived at NASA Goddard! The VUVAS-10X spectrophotometer works best in the 90 to 160 nanometer wavelength range, also known as deep or vacuum ultraviolet (VUV) region. It uses a windowless hydrogen plasma light source and differential pump section to reach many wavelengths beyond those of conventional deuterium lamps. The source also works with other gases, or gas mixtures, for atomic spectral line emission from about 30 nanometers (double ionized Helium gas) up to the Visible light range. The new spectrophotometer system, McPherson VUVAS-10X, uses a one-meter focal length high-resolution monochromator with the special light source, scintillated detector and Model 121 goniometric sample chamber. The system is ideal for optical transmission, absorbance and specular reflectance at incident angles up to 60 degrees. This McPherson spectrophotometer system will help develop, inspect and qualify optical materials and coatings used for very high altitude and extraterrestrial space flight missions.
-
product
PXI-6230, 8 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Hybrid, Multifunction I/O
779616-01
8 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6230 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6230 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6230 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
Pressure Pumps, Fittings And Hoses
Practical Instrument Electronics, Inc.
Choose from 3 different pressure pumps depending on your requirements. All pumps are rugged metal construction with 2 outlet ports for connections, a fine adjust piston and a precision pressure vent. Pumps come standard with one 3′ 6900 PSI hose and a 1/4″ male NPT fitting.
-
product
Small Form Factor (40×70×12mm) CATV EDFA Module (Full function)
EATV5100-FM01
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5100 series is a low noise, high performance, high cost-effective EDFA module, which is specially designed for CATV system. EATV5100-FM01 is a full function module, using 40×70×12mm mini package, with single channel and narrow bandwidth standard version. A standard 6-pin electric connector provides simple electrical connection. The module adopts a high performance uncooled pump laser, the output optical power up to 19dBm.
-
product
SK Elektronik FID Analyzers
The Thermo-FID is an MCERTS approved extractive gas analyzer for the measurement of Total Organic Hydrocarbons (TOC) with a Flame Ionisation Detector (FID). Available in a number of different models, each version of the Thermo-FID employs the same detector unit, internal tubing and electronics. Distribution of sample and test gases is provided by using an innovative vacuum system which can be driven using plant compressed air or diaphragm pump.
-
product
EDFA
SOA1550-32(64)
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
product
Motor Testers
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test steel casing motor such as pump, fan, air-condition motor, mower, paper shredder and refrigerator etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
Water Level Controller with Timer & Overflow Sensors
IM1730
Ajinkya Electronic Systems provides water level controller which is most popular in housing societies. Water is a precious natural resource and it’s our social responsibility to save water whenever and wherever possible. In cities we get treated water and which makes it more precious. So there is a need to use this resource judiciously and carefully. In societies there are overhead tanks which gets filled periodically from the underground tank. The prosess requires man power for timely switching off the pump to avoid dry running as well as overflow of the water. The water level controller for societies offers a smart solution for pumping of the water to overhead tanks in buildings
-
product
Transportable Gas Analyzer
CGT-7100
The CGT-7100 analyzer measures the concentration of gases in a continuous way, using a ratio photometric non-dispersive infrared absorption (NDIR) method. All pretreatment parts required for measurement, such as the pump, filter, and electric dehumidifier, are built-in. The analyzer can measure three components including CO, CO2, or CH4 (any two of these) and O2, and is compatible with measurement at 100 vol%. The CGT-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
product
High-Frequency Test Coil
West Coast Custom Designs, LLC
is most commonly used by the neon industry for detecting leaks in a pumping system; the spark generated by the coil via the solid tip, will enter the tube through the leak and become bright white at the point at which it enters.
-
product
Reciprocating Pumps
ReaXus
Teledyne LABS ReaXus® reciprocating pumps covers a broad range of application needs, ranging from 5 mL/min to 300 mL/min and up to 6,000 psi. Whether you need low pulsation or are working with hazardous materials, the ReaXus line has an option for you. The single piston models are targeted towards moving material or providing pressure. The dual piston models are focused on continuous processing applications where a steady flow of material is important.The ReaXus product line is low maintenance and requires no calibration like other styles of pumps, saving your organization time and money.
-
product
NTS Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
product
HPLC Pumps
MX Class
Further applications include demanding metering and dispensing, as well as Sample Injection, Infusion, or Cone Wash for Mass Spectrometers. Standard fluid path material is Stainless Steel. With flow rates up to 10 mL/min, these pumps can tackle the majority of demanding laboratory applications.Features include pressure monitoring with automatic pressure compensation, Pulse Dampener, integrated Prime-Purge Valve, interactive keypad control, and complete PC control and status through RS-232, micro-USB 2.0, and Ethernet serial communications. Requiring minimal bench space for the performance, the MX Class will easily integrate into most workspaces.
-
product
Engine Mounted Gearboxes (EMADs)
Engine mounted accessory drives (EMADs) — Our EMADs are manufactured with care and precision, using TRIUMPH Geared Solutions or customer designs to meet the engine manufacturers’ specifications. Low profile casings help minimize engine frontal area and facilitate engine installation. EMADs provide power for fuel pumps, alternators, and lubricant and scavenge pumps. TRIUMPH Geared Solutions contributes to prototype EMAD design and manufacture, such as for the F119 and YF120 engines. Triumph Geared Solutions EMADs have also gone into service on many military and civilian engines.
-
product
Gasmet Calibrator
Gasmet portable calibrator is one of the most important tools in generating new applications for the Gasmet FTIR gas analyzer. The calibrator incorporates a syringe pump, a manual needle valve, a mass flow meter, and a stainless-steel injection chamber. The syringe pump injects precise amounts of liquid or gas into a hot nitrogen gas flow, thus producing a continuous flow of a known concentration calibration gas.
-
product
Raman Spectrometer
S-RS
Main features of this system are an adaptation a super stable single mode 500-picosecond pulsed Diode Pumped Solid State Lasers (DPSSL) with more than 8 kW peak power as a probe beam.
-
product
DC-DC Charge Pumps
Charge pumps – inductorless boost converters – from ams operate at up to 90% efficiency.
-
product
Cooling Systems
Aerodyn Engineering designs and manufactures its own line of cooling carts. Our cooling carts will supply filtered coolant to the slip ring while in operation. Aerodyn Engineering’s cooling units are extremely reliable and are designed and manufactured with the highest quality components and craftsmanship available in the industry today. Magnetically coupled pumps are employed within our system to deliver the cooling fluid, with full user instruments showing flow rate and system pressures.
-
product
Dead Weight Pressure Tester
Unitech Scales And Measurements Pvt. Ltd
Dead Weight Pressure Gauge Tester is ideal for testing and calibration of pressure gauges,pressure transducers,recorders,digital calibrators etc. The system used in the dead weight is vertically mounted precision lapped piston and cylinder assembly with accurately calibrated mass for loading the piston. Pressure is built easily by single cylinder pump at very high rate. The whole system is housed inside a stainless steel case with elegant look. Pressure ports are provided to fix the gauges to be tested. Acrylic see-through oil tank is designed to use it as oil reservoir.
-
product
Temporary Power Outlet
K-271, K-272, and K-273
Knopp’s Temporary Power Outlets are an easy and safe solution for construction sites or other areas where power is not easily accessible. The device provides temporary electric service by isolating power from the breaker panel. Easy-to-use and versatile, Knopp’s Temporary Power Outlet eliminates the need for portable generators and can be used for motor homes, travel trailers, marine shore power, construction sites, and solar pump stations. Emergency situations such as hurricane restoration, storm outages and fire damage can also utilize this device.
-
product
Heavy Duty Pressure Transducers
PX3 Series
Honeywell Industrial Automation
Honeywell is pleased to announce its efficient, affordable and durable PX3 Series Heavy Duty Pressure Transducers, designed primarily for system pressure monitoring in HVAC, refrigeration, air compressor, pump and valve systems. Key features and benefits include: Delivers high efficiency: Proven, 1.0% FSS tight Total Error Band accuracy promotes system efficiency and lower energy costs. Great customer value: Economical choice for design/implementation; extremely flexible with multiple configuration possibilities with the right combination of features and broad media compatibility. Durability promotes system uptime: For enhanced performance in tough environments to support overall system quality, reliability and warranty. Fast availability: Short lead times on samples and production parts.
-
product
Pressure Calibrators
Wherever you need to work and whatever pressure range you need to work with, our broad selection of tools will meet your needs. From pneumatic or hydraulic deadweight testers and test pumps to electronic deadweight testers, bench controllers, and precise analog pressure gauges, we have you covered at the bench. Going into the field? Fluke’s portable pressure calibrators – with or without pumps and intrinsically safe or not – work with gases or liquids, source and measure, power transmitters, and cover a wide range. With individually available pressure modules, our portable and bench solutions cover pressures from vacuum to 10,000 psi.
-
product
Scanning Droplet Cell
VS-SDC
Scanning Droplet System (SDC) uses a compact peristaltic pump to force electrolyte through a small diameter tube and into a specifically designed head. This PTFE-based SDC head is machined to allow electrolyte to flow past an installed Reference Electrode and then to a port at the base of the head.
-
product
Multipoint Sampling Systems
Gasmet Multipoint Sampling System (MSS) is designed for online monitoring of multiple measuring points.The Gasmet MSS consists of a wall-mounted stainless steel case which includes all valves, flow meters, and pump. Standard setup includes one pump with four (4) sample gas input line, but up to 32 lines can be added according to customer need. Additionally, a second sample gas pump can be added to reduce the system response time.
-
product
Versatile, Heavy-duty Hydraulic Test Centers
HTC Series
For powertrain testing it’s all about fast and exceptional results achieved in the safest manner possible. Our Hydraulic test stands HTCs offer full functionality to test all types of transmissions, motors, cylinders, valve blocks, torque converters and pumps. As you evaluate your needs for heavy-duty mobile testing equipment, consider how upgrading to the latest technology can improve your bottom line.
-
product
Embedded Systems
Embedded systems consist of computer hardware, input and output (I/O), and software typically used for system control or monitoring applications. Our engineers are experts at integrating control system electronics with components and sensors, including motors, pumps, valves, signal transducers, and much more. We have developed and deployed thousands of systems that include industrial assembly lines, scientific instruments, medical devices, large installations like factories, manufacturing equipment, and electrical grids that rely on multiple embedded systems networked together.
-
product
IQpump Drives
Our drives were designed with the pump service operators and pump system owners in mind and offer ease of setup and comprehensive pump and motor protection features.
-
product
400 HP Complete Bench Hydraulic Test Center
HTC-400
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 400 hp (298 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators).The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
product
Chemiluminescence NO/NO2/NOX Analyzer
Model T200
Teledyne Advanced Pollution Instrumentation
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.
-
product
Vertical Pumps
The range of Flowserve vertical pumps covers wet-pit, double case, submersible, slurry and solid handling, sump and concrete volute configurations. They comply either with ISO, ASME or API standards, and guarantee reliable and efficient processes. Numerous sizes, hydraulics and material combinations are particularly well suited for use in applications where uncompromising reliability and efficiency over a wide flow range are key.
