Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transp...show more -
product
PXI 16x16 Matrix Module, 2-Pole, 2A, 60W
40-582-001
The 40-582 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 16x16 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 78 pin D-Type connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
product
Drivetrain Tester
G5.DT
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
PhyView Analyzer
The PhyView Analyzer dramatically simplifies the task of Ethernet 10/100/1000 interface testing in finished products without the need for test fixtures, test signals, scopes, and probes.
-
product
DDLS 200 with 2 Mbit/s Transmission Rate
Leuze electronic GmbH + Co. KG
Optical data transmission for RS interfaces and fieldbuses up to 300 m and up to 2 Mbit/s. Infrared data transmission protects the DDLS 200 from interference. Systems are available for all common industrial fieldbus interfaces. The ranges are stepped and reach a maximum transmission distance of 300 m. Low ambient light sensitivity through special FSK method. Available interfaces: PROFIBUS, Interbus and CAN/DeviceNet, as well as RS422 and RS 485.
-
product
Heat Stress WBGT Meter
Heat Stress Index measures how hot it feels when humidity iscombined with temperature, air movement, and radiant heat Black Globe Temperature (TG) monitors the effectsof direct solarradiation on an exposed surface Air Temperature (TA) plus Relative Humidity (RH) Selectable units of F and C In/Out Function displays the WGBT value withor without direct sun exposure Auto Power Off with override Built-in RS-232 interface with optional Windowscompatible software Complete with two AAA batteries
-
product
Anite Development Toolset
Benefit from a comprehensive suite of tools that support all phases of wireless terminal development, from pre-silicon protocol module development through to systems integration and verificationGain easy access to parameters at lower layers to re-create tests in the very early stages of chipset and device developmentAccess an extensive LTE/LTE-Advanced technology roadmap including early 5G specificationsRemain in control of test designs through accessing Layer 1 and Layer 2 using Application Programming Interfaces (APIs)Benefit from a high level of flexibility and control in terms of test creation
-
product
60W Dual Output Power Supply Two 35V, .8A or 60V, 0.5A
E3647A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 58W, multiple output E3647A is a clean, reliable power supply for general purpose applications, and combine convenient benchtop capabilities with flexible system features in a compact, multi-output package.
-
product
Multi-Channel, Multi-Protocol 1553 and ARINC 1/2 Size PCIe 4-Lane Interface Card
PCIEC4L-MA4
Alta Data Technologies’ PCIEC4L-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC ½ size PCI Express 4 Lane interface card (PMC on 4 Lane PCI Express Carrier) is supported by the latest software technologies. The PCIEC4L card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
8-Channel Relay Output Board With Housing for Mounting on a DIN Rail
PX8500-G
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
product
50 Ohm MCX to MCX Cable Assemblies - 3GHz
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - PCIe
Model 78751
Model 78751 is a member of the Onyx® family of high performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter with aprogrammable DDC, it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution as well as a platform for developing and deploying custom FPGA processing IP. It includes two A/Ds, two D/As and four banks of memory. In addition to supporting PCI Express Gen. 3 as a native interface, the Model 78751 includes a general purpose connector for application-specific I/O.
-
product
MTM Ribbon Cable Interface
ELEGANT CONNECTIONS: The S91-MTM-RCI-1 Ribbon Cable Interface connects non-MTM equipment into MTM-based systems. Bridge external test tools to an MTM test-point carrier board (TPCB) using wired ribbon cable, headers, or terminal blocks.
-
product
Thin-film deposition
Plasma Source
SPECS Surface Nano Analysis GmbH
Thin-film deposition covers any technique for depositing material onto a bulk or thin film substrate. Elemental alloy or compound films are produced by non-reactive or reactive (co-)deposition. Often functionalization or tailoring of device interfaces by predeposition or deposition assisting surface treatment with atoms or ions is necessary.
-
product
75 Ohm 1.0/2.3 Cable Assembly
40-977-731-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Half Slim SATA3 RunCore Embedded SATA3 “Elite Series”
RunCore Innovation Technology Co. Ltd.
Half Slim SATA3 utilizes high-performance SATAIII SSD controller and NAND flash, with or with no DRAM buffer to support power failure mechanism. This series SSD compliant with Serial ATA Revision 2.6/3.1 specification, compatible with 6.0Gbps, 3.0Gbps and 1.5Gbps interface rate and support Native Command Queuing (NCQ) up to 32 commands. As a standard SATA drive, it can support mainstream OS, such as Windows/Linux/Unix/Solaris/ Mac OS and so on.
-
product
3U CompactPCI Serial Blades
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
product
Human Machine Interface
Panasonic Automotive & Industrial Systems Europe GmbH
combines state-of-the-art features and top performance with an outstanding design in an all-metal housing. The range consists of four models in sizes from 4.3", 7", 10.4" and 13.4" TFT color display with LED backlight. All models can be installed in a horizontal or vertical position. The touch terminals are equipped with an Ethernet port and support VNC technology, allowing both remote VNC applications and remote assistance. The HM500 series is programmed with the HMWin software, a simple and in...show more -
product
Embedded PCs
Advantech Embedded PCs (EPC) are a full range enclosures systems designed for Mini-ITX motherboards and 3.5" single board computers, featuring optimized mechanical design and flexible I/O interface options, assuring maximized flexibility for design in efficiency.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - XMC
Model 71851
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex Ultrascale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL...show more -
product
Laser Diode Reliability Burn-In / Life-Test System
58602
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 2m HV, Exit Towards Pin 1
A050DM5-F-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
USB-8506 , LIN Interface Device
784664-01
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN fr...show more -
product
Laser Distance Meter with Compass
TRUPULSE 360(B)
F. W. Breithaupt & Sohn GmbH & Co.KG
*Scope magnification 7-times*Field of view 100m/915m distance*LCD Display*Range to non-reflecting targets 1.000m*Range to reflecting targets 2.000m*Accuracy in range ± 30cm (± 1m to weak targets; shown in display)*Accuracy in slope ± 0,25°*TruVector Compass Technology*Accuracy of compass ± 1° typical*RS 232/Serial interface (Model B: with Bluetooth)*IP protection IP54
-
product
Bus Isolation Board
MS 1705
- Bus Interface - ISA96 Bus, 6U form factor- 16-bit Data Bus- 20-bit Address Bus & Control Signals- Isolated Bus Interface- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
PXIe Remote Control Interface Module
43-921-002
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
product
Digital "A" Flow Controller for Low Flow
HFM-D-300A / HFC-D-302A
HFM-D-300A / HFC-D-302A mass flow instruments have flow ranges from 0-5 sccm to 0-25 slm; use all metal seals, provide analog and digital outputs, and are constructed of stainless steel. Easy, user friendly digital communications with windows based software interface available.Self diagnostics of the sensor, valve and overflow are included in the digital features. Also of interest is the auto zero feature which detects when the valve is closed and automatically resets the zero. These mass flow meters and controllers can store up to 10 calibrations of different ranges and gases. Another feature is the built in totalizer for monitoring gas usage under user set conditions.
-
product
PXI Single SP6T Multiplexer 40GHz 50 SMA-2.9
40-784A-041
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Male (Male Screwlocks), 0.5m
40-970B-200-0.5m-MM
This male to male 0.5m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by male screwlocks.
