-
Product
SparkFun Digital Temperature Sensor Breakout
TMP102
-
The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of the Arduino to communicate the temperature. Needless to say, this is a very handy sensor that doesn't require much setup.
-
Product
Reach-In Temperature Environmental Chamber
-
Burnsco Environmental Test Chambers
Our popular reach-in chambers have been designed for maximun testing flexibility while remaining a standard, cost saving unit.
-
Product
Temperature Humidity Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature and Humidity Test Chamber is able to simulate a wide range of temperature and humidity environment condition for testing various products and components. It is widely used for basic thermal cycling test and accelerated stress test. We provide 6 standard models, test cabinet from 80L to 1000L, customized size is also available.
-
Product
LilyPad Temperature Sensor
-
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
Product
Stand-Alone, Humidity and Temperature Data Logger
RHTemp1000
-
The RHTemp1000 humidity and temperature data logger is a rugged, battery powered, stand alone device which can be used to automatically record humidity and temperature. This all in one compact, portable, easy to use device is able to measure and record data for up to 21,845 humidity and temperature measurements.
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Combined Temperature and Altitude Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Altitude & Temperature Test Chamber combine Altitude and temperature to test various components and products, especially the aircraft avionics. Automatic controlled vacuum system provide a precise altitude simulated condition up to 30000 meters. Available to connect cable for the electronic performance test.
-
Product
Miniature, Battery Powered, Stand Alone Pressure and Temperature Data Logger
PRTemp101A
-
The PRTemp101 is a miniature, battery powered, stand alone pressure and temperature data logger. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged.
-
Product
PRO Waterproof 3-in-1 Conductivity / TDS & Temperature Tester
EC59
-
The Milwaukee EC59 PRO Conductivity (EC) & Total Dissolved Solids (TDS) Tester is designed for aquaculture, food, wine, laboratory, water treament and many other applications. It is the ideal meter to help make sure that your EC/TDS/Temp. needs are being met and are reliable results for your analysis. Keep EC/TDS/TEMP. in your target range to help your achieve best results.
-
Product
WaveLink Temperature Extension cables for Dx20
Dx20-HiTemp
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Immersion Temperature Probe
U1181A
-
Measure the temperature of food, oil, and other liquids within the range of -50°C to 700°C.
-
Product
Economic Type Temperature Indicator
CS1-T
-
CS1-T economic type Temperature Indicator has been designed with high accuracy measurement, display and communication of Thermocouple or Pt100Ω.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Data Logger for Extremely Low Temperature
DSR-ELT
-
Special probe using military industrial technology supports measuring temperature ultra low to -196 Original fittings for sensor connection, ensures 100,000 plugs Support single DSR connecting to PC via USB interface, and multiple DSR grouped in RS485 or LAN networking for central management Suitable for medical refrigerator, biological specimens preservation, scientific research and other applications
-
Product
Temperature Logger-30 to +50C
TV-4050
-
This data logger is a self-contained temperature recorder with a digital display. The TV-4050 is ideal for monitoring the temperature of offices, cold storage rooms, museum exhibits and many other applications where a visual temperature indication is needed.
-
Product
Walk-in Environmental Chamber for Temperature Humidity Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's walk-in environmental chamber for temperature humidity testing is perfectly meet the large size test application that require high temperature and high humidity. The walk-in chamber is constructed with structural steel, so it is able to test the large components and products. Various optional function available for different test standard and requirement.
-
Product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-H
-
Breakout board for the Sensirion SHT31-DIS-B. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
Product
High & Low Temperature Impact System for ATF Cooling Motor
EVTP-30
-
Shanghai Dean Electrical Co., Ltd
This test system provides the most direct life evaluation of ATF cooling based EV motor by simulating the temperature impact from ultimate self- heating of the motor and severe cold condition from environment.
-
Product
Temperature Stabilized Antenna
TSA-100
-
A major source of error in timeand frequency receivers is the variationof signal delay due to changes in the outdoor temperature. The designofthe TSA-100 includes two fully independent thermal zones, each with itsown precision heating and cooling capability. The result is that thetemperatureof the preamp is maintained within ±0.5°C over an ambient temperaturerange of -20°C to +50°C. This system virtually eliminates bothseasonal and diurnal variations, supporting exceptionalrepeatability.
-
Product
Temperature and Process Controllers
-
The ATR121 Temperature Controller is a 3 digit display PID controller with up to 2 relay outputs, Solid State Output and an option to be a Modbus RS485 Slave device.The ATR141 Temperature Controller is a 4 digit PID controller and Panel Meter which can display up to 3200°F with an S Type Thermocouple. The ATR141 can have up to 2 relays, a Solid State Output and an option to have a Modbus RS485 output.
-
Product
Remote Temperature and Humidity Sensor
CHV-RTHS
-
The CHV-RTHS is a wall-mounted remote temperature and relative humidity sensor designed for use with select Crestron thermostats. The 1-1/2 inch diameter face of the CHV-RTHS protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
Product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T01
-
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E002
Thermocouple Contact
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Transducers for Temperature
-
Overview of transducers with Ethernet interface for temperature and humidity.
-
Product
Intrinsically Safe Temperature Meter
Ex-MP4 a
-
The intrinsically safe, non-contact temperature meter equipment Ex-MP4 a is a robust yet exceedingly handy and easy to use instrument for temperature measuring ex-hazardous areas. Certification No.: EPS 10 ATEX 1242 X
-
Product
System for UHV Temperature Programmed Desorption (TPD) Studies
TPD Workstation
-
The Hiden TPD Workstation is a complete experimental system for UHV temperature programmed desorption (TPD) studies. The triple filter mass analyser is configured with a cooled shroud giving the analyser optimum sensitivity with minimum background contributions to desorption products from the sample. A fast sample load lock with sample transfer mechanism is included to provide for rapid sample change. The TPD Workstation features a multiport UHV chamber with heated sample stage coupled to a high precision triple filter analyser with digital pulse ion counting detector for ultimate sensitivity and time resolution.
-
Product
Temperature, Humidity, CO2 Transmitter
T6340
-
The transmitters are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
High Temperature Wettability Tester
6200Z
-
This device is a test device that evaluates the wetting stress generated between a plate/round bar and molten metal in an inert gas atmosphere by the wetting balance method.It is possible to analyze not only the quality of wetting but also the wetting phenomenon from the obtained wetting curve.
-
Product
Humidity and Temperature Measurement Accessories
-
Find our selection of most frequently used accessories such as filter and filter carriers to protect your sensor against mechanical influences or a range of accessories for mounting, connecting, installation, maintenance and calibration of your humidity and temperature instruments.
-
Product
Temperature Probes
-
Is a device, typically, a thermocouple or RTD, that provides for temperature measurement through an electrical signal. A thermocouple (T/C) is made from two dissimilar metals that generate electrical voltage in direct proportion to changes in temperature.
-
Product
High Low Temperature Test Chamber
-
The high low temperature test chambers from Weiber are climatic test chambers, designed to simulate highly precise high and low temperature environments for the testing of electrical and electronics items, metallic products, automobile parts, food items, biological samples, chemicals, building materials and other wide variety of processed and packaged goods. These test chambers find widespread usage in manufacturing units, quality control units and scientific research organizations and are commonly employed for heat endurance test, cold endurance test and humidity and dryness endurance tests of products. These tests help in determining the product performance in specific environments and also help in identifying any manufacturing flaws and in determining its stability and shelf life.
