Conformance
assures device performance within a specific range of requirements.
See Also: Performance Testing, Compliance
-
Product
Conformance Testing Software
Clarinet-TTCN VOIP Interworking ETS
-
Protocol: ITU-T H.225 (11/2000) H.323 (11/2000) and ITU-T Recommendation Q.784.2 (1997)IUT: H323-ISUP gatewayATS: Based on H246 standard of ITU-T written by ACACIA .
-
Product
Conformance Testing
Clarinet-TTCN SS7 ETS
-
Protocol: ITU-T Q703 standard defines protocol for Signaling System No. 7 – Message transfer part IUT: SS7 Signaling Point - MTP2-ITUATS: Based on ITU-T Q781 (07/96) test descriptions.
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
Radio Conformance Analyzer
RCA G9200
-
LTE test solution for development, verification and conformance testing of LTE mobile equipment. The G9200 RCA is able to perform analysis of LTE mobile devices at all layers from the physical to the application layer, and is suitable for development, conformance, pre-conformance, and production test applications.
-
Product
Telecom Conformance Analyzer
TCA 8200
-
The TCA 8200 is an all-in-one conformance testing solution, according to worldwide regulatory & industry standards, for many types of telecom equipment ranging from phones, cellular phones including LTE to digital switches, PBXs and VoIP gateways.
-
Product
NFC and EMVCo Conformance and Design Validation Solution
Micropross MP500 TCL3
-
The MP500 TCL3 Generator/Analyzer is a high-performance test solution for designing and characterizing NFC devices. Built specifically for the laboratory environment, the MP500 TCL3 offers advanced signal generation features for unmatched flexibility. It supports the following standards:
-
Product
SpaceWire Conformance Tester
313
-
The SpaceWire Conformance Tester connects to a SpaceWire device and, through the host software, executes a variety of tests to check the unit under test’s (UUT) compliance to the SpaceWire Standard. Over 55 tests are conducted across the following levels:
-
Product
Receiver Conformance Test Application for OIF CEI 5.0
M809212CA
-
OIF Receiver Test Application for CEI-112G-VSR,-MR and -LR PAM4 interfaces.
-
Product
PD Conformance Test Suite for 802.3at & 802.3bt
-
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
Product
Conformance Test Solutions 3GPP / Regulatory (CTIA / RED)
-
Only conformance test sytems from Rohde & Schwarz cover all relevant digital mobile device generations.The key to success is comprehensive access to RF, RRM, LBS and PCT test cases as defined e.g. for 5G NR in 3GPP TS 38.521-1 to -4 (5G NR RF), 38.533 (5G NR RRM), 38.523-1 (5G NR PCT), 37.571 (LBS).The Rohde & Schwarz conformance test solution portfolio consists of approved test platforms for device certification by GCF and PTCRB that support both TDD and FDD and all relevant 5G NR bands in both sub-8GHz (FR1) and mmWave (FR2) frequencies, as well as all frequency bands for LTE, WCDMA and GSM.
-
Product
Conformance Test Systems
-
With an established market leadership position in GCF and PTCRB approvals for LTE-Advanced and all leading-edge technologies, Anritsu continues expanding its number of test case validations in GCF and PTCRB for Protocol, RF and RRM conformance testing. With increasing complexity of wireless technologies, Anritsu Conformance Test systems provide easy-to-use control software to maximize testing efficiency.
-
Product
Anite Conformance Toolset
-
Ensure mobile devices perform as expected on a live mobile network by verifying their compliance with latest industry specificationsUse independently validated test cases when performing GCF and PTCRB device certification testingAccess comprehensive test case portfolio covering all GSM-evolved technologies, from GSM through HSPA+ up to the very latest LTE-Advanced and IMS test cases
-
Product
Conformance Calibration Standard Test Card for ITF-14 (Interleaved 2 of 5) Symbol Verifiers
AI-CCS-ITF-14
-
This test card is ideal for testing verifiers, scanners, and other ITF-14 (Interleaved 2 of 5) barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.
-
Product
PSE Conformance Test Suites
-
Whether testing single port injectors or 48 port PSE’s, Sifos offers the ultimate solution to assess PSE conformance to all applicable IEEE specifications. With the click of a button, fully automated testing and reporting delivers comprehensive and informative results including difficult-to-spot intermittent conformance behaviors. Available to PSA-3000 and PSA-3402 PSE test instruments.
-
Product
Conformance Calibration Standard Test Card for ISO/IEC Data Matrix and GS1 DataMatrix Symbol Verifiers
AI-CCS-DM-G Rev A
-
This precision 2D barcode Conformance Calibration Standard Test Card is the first 2D test card to provide ALL 12 of the Primary Reference Symbols specified by ISO 15426-2 for barcode verifiers. They are sized from 0.5mm to 0.2mm so that all the symbol sizes specified in Annex A.3.1 can be tested. Symbols 1-4 are GS1 DataMatrix symbols, while symbols 5-12 are ISO/IEC Data Matrix symbols consistent with the ISO/IEC 16022 standard. The card also includes four calibrated reflectance patches.
-
Product
Telephony Conformance Analyzer
TCA 4100
-
Acoustics and voice quality conformance testing for cellular including VoLTE, digital, and analog phones. TCA 4100 is an automated & affordable voice quality & acoustics conformance test solution. A wide range of handset and hands- free phones such as VoIP, DECT, Wi-Fi, Bluetooth, cellular, analog, telephones, audio devices and hearing aids are supported.
-
Product
Electrical Receiver Conformance Test Application for OIF-CEI 4.0
M809256CB
-
OIF-CEI 4.0 receiver test application for OIF-CEI 56G very short reach, medium reach, and long reach PAM4.
-
Product
Power Supply 1950W
PS236 / CS236 1100W
-
The high density high sophisticated PS236 power supply series replaces the well used PS336 types. PS236 is only 3U high and features six separately regulated extremely low noise outputs for use in CAMAC crates conforming EUR 4100 as well as CERN EP82-01 / EP84-01 and 46-04 specifications as well as in NIM bins UEN01 HC 12.
-
Product
Metro Expert
MX Series
-
The VeEX® MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/ Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
Product
MTA Wiring Analyzer
2650
-
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
Product
Ohm-Stat Ground/Circuit Tester to Test ESD Ground
-
Tests ground for all 110v electrical circuitsWill determine the status of all electrical groundsEasy to use LED lightsWarranteeProduct conforms to the ESD S.20.20 spec standardsIdentify electrical problemsUsed with the Ohm-Stat RT-1000 resistivity meter
-
Product
Signalling Relays
N.S1
-
N.S1 signalling and vital relays are a consistent, adaptable range of relays with plug-in connection, small size, modular construction, low power consumption, compliant to French and SNCF standards, conformity to UIC recommendation, Ag / Ag CdO contacts and 24 V standard.
-
Product
12 Port PCI Express
PEX 8615
-
The ExpressLane™ PEX 8615 offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8615 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
LXI 16:1 Optical MUX FC/APC Loop-Thru
60-850-023
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
ISO/ANSI Compliance
-
The ANSI and ISO/IEC standard for the C Programming Language specifies that there are two forms of conforming compiler implementations: hosted and freestanding.
-
Product
Ozone Aging Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Ozone aging test chamber is also called as ozone climate simulator or ozone aging tester. It is one of climatic testing instruments, which is to simulate and intensify the ozone condition for determining the cracking resistance of vulcanized or thermoplastic rubbers when subjected to dynamic or static tensile strain exposed at a man-made constant temperature to atmosphere containing given concentration of ozone in conformance with relevant specification. Ozone test is an indispensable method for people to research effects and mechanisms of ozone on rubbers, quick identify and evaluate anti-aging performance of rubbers and find solutions for improvement of quality and lifespan.
-
Product
High-Voltage Test Hood
HVE900
-
The large, bright test room with a ball-bearing cover is designed for high production quantities. Thanks to the easily exchangeable exchangeable plate, retrofitting for testing different products is also a simple task. Product properties: External dimensions (W * D * H) approx. 940 * 716 * 640mm Usable test space (W * D * H) approx. 750 * 500 * 460mm Contacting Installation space approx. 100mm high under removable plate Dielectric strength min 10kV Application area up to 2000m above sea level Pollution degree 1 without condensation Standard conformity EN50191 / EN61010-1 Schmersal safety switch AZM161 with guard locking Lid is supported by ball bearings for high number of cycles, the bearings can be easily exchanged for servicing Optionally available, Not included in the price: - Red / green signal light - Mobile substructure trolley with 19 "
-
Product
Inspection Solutions
-
Entire range of optical inspection systems. From the SPI machine (SPI inspection) for checking solder paste printing, to an inline AOI for THT or SMD-assembled PCBA, to AXI machine for BGA x ray inspection. And furthermore, GÖPEL electronic's AOI PCB inspection can be used for conformal coating inspection (CCI) of various protective coatings applied to boards.
-
Product
Sematech Analysis and SEMI Standards Analysis
-
Rocky Mountain Laboratories, Inc.
Rocky Mountain Laboratories, Inc. provides SEMI Standards analyses that conform to the following SEMATECH and SEMI Standards for testing of passivated 316L stainless steel components being considered for installation into a high-purity gas distribution system:SEMASPEC #90120401B-STD (SEM Analysis)SEMASPEC #90120402B-STD (EDS Analysis)SEMASPEC #90120403B-STD (XPS Analysis)SEMASPEC #91060573B-STD (Auger (AES) Analysis)SEMI F60-0306 (based on F60-0301) (XPS Analysis)SEMI F72-1102 (Auger (AES) Analysis)
-
Product
Automotive Radar Testers
-
Rohde & Schwarz provides automotive manufacturers, components suppliers and test houses with innovative, cutting-edge solutions which bring realistic test scenarios from the road to the lab and production line.Our range of solutions include a signal generator-based target simulator, a radome & bumper tester and an anechoic automotive radar test chamber allowing for over-the-air (OTA) testing. These solutions are at the heart of the development of advanced driver assistance systems (ADAS) with its safety-critical features such as emergency braking. Using T&M solutions by Rohde & Schwarz enables a thorough testing of chipsets, sensors and modules at each phase from development and conformance to production.
