Conformance
assures device performance within a specific range of requirements.
See Also: Performance Testing, Compliance
-
Product
SpaceWire Conformance Tester
313
-
The SpaceWire Conformance Tester connects to a SpaceWire device and, through the host software, executes a variety of tests to check the unit under test’s (UUT) compliance to the SpaceWire Standard. Over 55 tests are conducted across the following levels:
-
Product
Multifunction Instrument
COMBI521EV
-
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
16-Port PCI Express
PEX 8664
-
The ExpressLane™ PEX 8664 device offers 64 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 16 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 64-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Single Front Slot Universal Low-Profile PCI To PCMCIA Adapter, External
P314B
-
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P314. This model, from the P-Series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
Product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
-
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
Product
Information Technology Testing
-
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing information technology products according to applicable standards. We help you not only verify the classification of your product, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
Product
VME64x 7U 84HP 17 Slots
-
Hartmann Electronic’s 17 slot 19” rack mountable VME solution – The VME64x 7U system. This VME chassis comes with two 400W cPCI hot-swap power supplies with vertically oriented card slots. This platform conforms to VITA 1.1-1997 while providing a high capacity yet practical packaging solution for high-performance processors.
-
Product
PANAVIA Modules
-
AIM’s PANAVIA test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core design with one processor for real time bus protocol support, massive memory and IRIG-B time code encoder/decoder functions are standard. AIM delivers versions of our modules with extended temperature range and conformal coating. With 8 Tx and 8 Rx channels per module, functions include autonomous transmit sequencing, continuous clock and data transmissions, host controlled double buffering, programmable interrupts, data selection on specific tag identifier, selectable triggers on data and/or tags with full protocol error injection/detection, real time bus recording and time stamping to ensure your bus integrity. Each module is delivered with a Board Support Package (BSP) comaptible to the legacy PCI and cPCI hardware modules.
-
Product
Multifunction Data Collection and Analysis System
9000
-
The Model 9000 DME System is a high performance multifunction data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER), Digital Fault Recorder (DFR), Dynamic Disturbance Recorder (DDR), and Continuous Recorder data in conformance with PRC-002-1 and PRC-018-1. All data recorded by the DME system is stored in IEEE C37.111 format and named in conformance with IEEE C37.232. The system also has a software option to enable the Phasor Measurement Unit (PMU) feature to provide streaming data in conformance with IEEE C37.118.
-
Product
LXI 16:1 Optical MUX SC Multi Mode
60-851-213
-
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
12 Port PCI Express
PEX 8614
-
The ExpressLane™ PEX 8614 device offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX 8614 architecture supports packet cut-thru with the industry's lowest latency of 140ns (x4 to x1) and offers two virtual channels for traffic prioritization in the system.
-
Product
Digital ESD Field Meter
FM-1126
-
Now with an ionizer probe attachmentIndicates voltage and polarityDigital display is updated every three secondsNon-contactPower on/hold and zero buttonsEasy to read 3.5" LCD displayRange: 1-20,000v1" spacer bar9v batteryLeather case includedProduct conforms to the ESD S.20.20 spec standardsChecks for class zero conformance
-
Product
5 Port PCI Express
PEX 8508
-
The ExpressLane™ PEX 8508 8-lane, 5-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device enables users to add low cost, scalable high bandwidth switching, both fan-in/out and peer-to-peer, to a wide variety of applications including office automation, network interface adapters, docking stations, AMC cards, and processor isolation for servers, storage, and communications.
-
Product
8 Port PCI Express
PEX 8509
-
The ExpressLane™ PEX 8509 8-lane, 8-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device with an equal number of lanes and ports can be used in a wide variety of applications including control planes in the communications and networking markets, embedded systems, multi-function printers, network interface adapters, medical imaging systems, industrial-control systems and AMC cards.
-
Product
Test Leads
8000 Series
-
The "SOFTIE" by Probe Master lets you say "goodbye" to hand fatigue and finger calluses. A soft probe that bends 90 degrees or more. A probe that conforms to the shape of your hand. This soft flexible probe bends gently to reduce wear and breakage of the lead. Many combinations are possible with the "screw on" accessories shown above. The 48" long, 18GA. test leads, are made of top quality silicone.
-
Product
Resistivity Monitor / Controllers
750 Series II Resistivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Resistivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
GAOTek Handheld Gigabit Ethernet Test Module
A0070008tek
-
GAOTek Handheld Gigabit Ethernet test module is a highly efficient test instrument which designed for Ethernet layout and integration tests which conforms to Ethernet test standards. This instrument is required for testing from physical layer to service layer of emerging (or next generation) networks. The Ethernet tester is the new Ethernet tester to qualify Ethernet service over LAN and RAN deployment. This is a highly efficient test instrument for service providers to ensure SLA KPIs with the subscribers.
-
Product
DC Power Analyser
AESPA01 series
-
Aarohi Embedded Systems Pvt. Ltd
The AESPA01 series is the enhanced version of Aarohi’s 2nd generation of compact power meters. The world’s best-selling power meter is the instrument of choice for a wide range of applications in production testing, quality assurance and Research & Development. Aarohi power meters are easy to use, cost effective and accurate for diverse applications such as the testing of electric devices, the development and evaluation of Pump Industries, Motor Industries, home appliances and induction cookers, battery and AC driven device testing, and conformance tests on uninterruptible power supplies.The exceptional low power performance of the AESPA01 and power consumption software enables users to easily test their instruments to Energy Star.
-
Product
Powered NIM Crate
NIM CERN-CE 300W
-
The CERN spec./CE NIM crate series represents modular designed NIM crates with linear regulated power supplies in excellent and proven W-IE-NE-R quality, conforming to EUR4100 and CERN specifications. These NIM crates are outfitted with 300W linear regulated, low noise plug-in power supplies for standard applications.
-
Product
4 Port PCI Express
PEX 8604
-
The ExpressLane™ PEX 8604 device offers 4 PCI Express Gen 2 (5.0 GT/s) lanes, which supports up to four ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX8604 is the industry's smallest 4-lane Gen 2 device and it enables users with the ability to connect multiple PCI Express endpoints which are used in a variety of consumer and embedded applications including Multi-Function Printers, wireless ethernet modules, IO expansion modules, Express Card applications as well as other low power applications.
-
Product
Vivarium Rooms
-
Darwin Chambers Company ALAAC, OLAW, USDA, and NIH-compliant Vivarium Rooms are designed for maximum value, sustainability, and conformance with applicable standards. We have over a decade of experience in working with researchers to provide humane and often precise conditions to meet their unique and specific needs. Vivariums are commonly defined as a place, such as a in laboratory, where live animals and/or plants are kept under conditions simulating a natural environment. Often, these contain both plants and animals, within a micro-ecosystem, often with controlled stability or controlled change of environmental variables. We offer various surface finishes, including all stainless steel, which are easy to maintain and may be sterilized to cleanroom standards. Compartmentalized enlosures are offered, which are modular and reconfigurable. Our rooms will accommodate plants as needed (we also provide plant growth chambers), and we offer control of humidification in conformance with current ALAAC mandates, sufficient air exchanges, available HEPA filtration of intake and/or exhaust air, standard screened equipment hous- ings, and other such considerations.
-
Product
Conformal Coating Inspection
-
Conformal coating plays a key role especially when electronic assemblies are used in products and systems that perform safety-relevant tasks. The coatings applied to the circuit board protect against environmental influences such as dirt, dust, moisture, condensation, and varying temperatures. Increasing packing densities and the trend toward miniaturization are also making conformal coatings essential. The insulating effect of the coating allows reductions in the distance between conductor paths while also boosting the performance of terminal devices.
-
Product
Ohm-Stat Guardian Pro Constant Monitor
-
Tests two people and two wriststrapsLED and buzzerNIST calibration includedWorks with all single wire capacitance wrist strapsAll cords suppliedCE markCan be calibratedProduct conforms to the ESD S.20.20 spec standards110v AC powerGround dock included
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
-
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
MPEG Stream Monitor / Validator
TeleSight
-
Real-Time validation including video and audio bitstream conformance, video quality, bitrate, and audio levels Supports up to 20 streams simultaneously. View real-time playback of all input channels simultaneously or zoom in on one (real-time playback performance is dependant on machine, number of streams, and content). Mix variety of inputs types. Mix variety of supported MPEG formats.
-
Product
3U 5-Slots OpenVPX P&G, w/o ROHS, 3.125G
101VPX305P-9K05
-
3U 5-Slots OpenVPX Power & Ground, Pass through, conformal coating, w/o ROHS, Max data rate (Gbps) 3.125.
-
Product
Conformal Ballistic Pressure Sensor
Model: 117B67
-
Conformal ballistics pressure sensor, 22 WMRF, 22 WRF, 22 WRF WITH 0.50" Centerline, 17 RF Mag, 17 HMRConformal ballistics pressure sensor for 17 HMR, 17 Magnum RF, 17 RF Magnum, 22 WMRF, 22 WRF, and 22 WRF with 0.50" centerline caliber cartridges.
-
Product
IEC60669 Pendulum Impact Tester
CX-BC2
-
Shenzhen Chuangxin Instruments Co., Ltd.
This Pendulum Impact Test Device Conforms to the standard GB2099.1, GB16915.1 and IEC60669, IEC60670 standard. To check the impact resistance performance of plug and socket electrical accessory's enclosure.
-
Product
Conformance Calibration Standard Test Card for UPC/EAN Symbol Verifiers
AI-CCS-UPC/EAN-E Rev S
-
For those who prefer a traditional vertical format calibration test card, APPLIED IMAGE offers our new Conformance Calibration Standard Enhanced for UPC/EAN Bar Code Symbol Verifiers. The new standard complies with both the ANSI X3.182 and ISO 15416 standards and is ideal for testing of verifiers, scanners, and other UPC bar reading equipment as well as a tool for training new operators to assure proper “methodology' in the use of verifiers.
