PCI Backplanes
-
Product
14-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB100
-
The FAB100 features one CPU card slot, four ISA slots, four PCI-E x1 slots, one PCI-E x16 slot, and four 32bit/33MHz PCI slots. This PICMG 1.3 backplane also supports a built-in 24-pin ATX power connector. Furthermore, the FAB100 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491 and AX6145, to house the FAB100 and any customer's industrial integrations flexibly.
-
Product
PXI / PXIe Backplanes
-
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
Product
PCI 39xSPST 2Amp Relay Card
50-132-003
-
The 50-132-003 39xSPST relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
PCI Evaluation Board
BCM91125E
-
The BCM91125E is a full-length PCI evaluation board with the SiByte® BCM1125H MIPS processor System on a Chip (SoC). The board is designed for software development and developing PCI applications, which require high-performance processors. The BCM91125E can be plugged into a PCI slot in any PC, workstation or server, or can be used as a stand-alone device.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
Low Profile PCI Express 1-Port
7106e
-
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
11-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB121
-
*Designed for PICMG 1.3 SBC*Compatible with AX61410, AX6145, AX6156 chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x4 slots, one PCIe x8 slot, and two 32bit/33MHz PCI slots
-
Product
PCI Express Waveform Digitizer
ATS9626
-
ATS9626 is a 250 MS/s 16 bit PCI Express waveform digitizer with an on-board, user-programmable FPGA. With fixed dc-coupled input range of +/- 1.25V and signal to noise ratio in excess of 72 dB, ATS9625 is an ideal solution for applications that require high dynamic range with dc coupling.
-
Product
88-lane, 44-port, PCI Express
PEX89088
-
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
-
Product
Passive XMC-to-PCI Express Adapter
5934
-
The Technobox, Inc. P/N 5934 is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
PCI Smart Bus Extenders
Live Insertion PCI Bus Extenders
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment. The capabilities of Ultraview's two models of Universal 66/33MHz 64/32-bit PCI extenders are as follows:
-
Product
6-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB210
-
*Designed for PICMG 1.3 SBC*Compatible with AX61222TP/AX61220TP chassis*Supports one PICMG 1.3 CPU card slot, two PCI slots, two PCIe x1 slots, and one PCIe x16 slot
-
Product
PCI Digital I/O Boards
PCI-822LU
-
Universal PCI, 250 kS/s, 32/16-ch 12-bit Analog Input, 2-ch 16-bit Analog Output with 32-ch Programmable DIO. Replacement for A-823PGH Series, A-823PGL Series, A-822PGH Series, A-822PGL Series, A-821PGH Series, & A-821PGL Series.
-
Product
Low Profile PCI Express 8-Port
7802ec
-
The 7802ec low profile PCI Express serial interface provides eight serial ports, each individually field-configurable for RS-422 or RS-485 communications. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7802ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
-
Product
32-bit PMC to PCI Adapter
8092
-
This PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
PCI Express Card
PCIe-ADIO16-16F
-
The PCIe-ADIO16-16F is a 16-bit resolution A/D & D/A card with two simultaneous 1MHz A/D converters, having a total of either 16 single ended, 8 differential, or 8 single ended and 4 differential inputs. Each channel can be independently software configured to accept any of 7 input ranges. Four analog outputs with 5, 10, ±5, ±10, and ±2.5V ranges are provided.
-
Product
12-Bit PCI Express ADC/Digitizer
SIS1350
-
The SIS1350 is our first PC add on digitizer card. It was developed for high repetition rate acquisition of short analog signals (i.e. up to 128 µs at 500 MSPS) with good resolution
-
Product
64-bit PMC to PCI Adapter
4930
-
This passive PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment.
-
Product
ASI/SD-SDI Input+output For PCI
DTA-145
-
DekTec's bi-directional dual ports ASI/SDI adapter, with genlock and watchdog-controlled input-to-output relay for redundant configuration.
-
Product
PCI Termination Products
-
Acromag provides a broad selection of hardware accessories to simplify the use of our I/O boards. This collection of panels, cables, and adapters facilitate field wiring and cable connections between boards within the card cage. Select from an assortment of cables and termination panels to simplify wiring and installation.
-
Product
PCI 16xSPDT 2Amp Relay Card
50-131-001
-
The 50-131-001 16xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
PCI Express Digital I/O Cards
-
Sealevel PCI Express digital I/O cards are designed for computers with X1 PC Express slots and are compatible with any PCI Express slot. Digital I/O cards are currently available with optically isolated inputs and Reed relay outputs. Optically isolated inputs protect the PC from voltage spikes common to industrial environments while Reed relay outputs provide reliable, long-life switch closures suitable for low current applications.
-
Product
PCI Multifunction Board
PCI-1602/8K
-
The PCI-1602/1602F series is a family of high performance and high resolution data acquisition boards for the PCI bus. It features a continuous, 100KHz for PCI-1602 (200KHz for PCI-1602F), gap-free data acquisition under DOS and Windows. The PCI-1602 family has the same hardware architecture as PCI-1802L. The PCI-1602 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1602 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
PCI Fault Insertion Switch Cards
-
Pickering's PCI Fault/Signal Insertion Switch Cards feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system.
-
Product
PCI Analog Output Boards
PISO-DA2U
-
Universal PCI, 2-Channel Isolated Analog Output Board. Includes two CA-PC09M D-Sub connectors
-
Product
PCI Multifunction Board
PCI-1800L/S
-
The PCI-1800 series is a family of high performance data acquisition boards for PCs with a PCI bus. It features a continuous, 330KHz for low gain (44KHz for high gain), gap-free data acquisition under DOS and Windows. The PCI-1800 family has the same architecture and has two 12-bit D/A output channels, 16 digital input channels, and 16 digital output channels. The PCI-1800H, PCI-1800L provides 16 single-ended or 8 differential inputs. The PCI-1802H and PCI-1802L provide 32 single-ended or 16 differential inputs. The -H means high gain model and the -L means low gain model. The scan function of PCI-1800 is so amazing. We call it Magic Scan. The variable channel scan function is found in some famous data acquisition boards. Compared to Variable channel scan, the Magic Scan improves a lot functions and meets the demand of high end users. The Magic Scan mechanism not only scans the different input channels at vastly different rates, but also at different gain. Even in multi-channel scans, the sampling rates can maintain at 330KS/s.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
6 Port PCI Express
PEX 8533
-
The ExpressLane™ PEX 8533 device offers 32 PCI Express lanes, capable of configuring up to 6 flexible ports. The switch conforms to the PCI Express Base Specification, rev 1.1. The 32-lane switch enables users to add scalable, high bandwidth I/Os to a wide variety of applications including servers, storage, communications, blade servers, and embedded-control systems.
-
Product
RTD Measurement for PCI
PCI390
-
The PCI390 features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm-limit checking. Sensor-data is available in °C, °F, K and Ohms. All inputs are optically isolated from the system.
-
Product
PCI Express To CPCI Board
MS 1719
-
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
