-
product
Probilt™ Probe Card Analyzers
ITC has a complete range of probe card metrology products that address all probe technologies, probe card sizes and probe counts.
-
product
Power Quality Analyzer
PQM-703
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
product
Wideband Swept Antenna, Cable Analyzer
SWR TRUE 3013
• A cost-effective SWR Analyzer covering all Cellular and radio communication bands 30-2700 MHz• Measures transmition & antenna impedance, frequency, SWR, return loss, and bandwidth by sweeping band of interest• Built-in synthesized RF sweep generator• SWR TRUE 3013 Antenna Analyzer gives you quick and reliable antenna and cable trouble-shooting capabilities• 5 in 1 analyzes for antenna tuning and control• Measured results can be stored for further analyzing and documentation on internal and external storage media• Time stamp and operator ID capability included• LCD Display works in direct sunlight and with backlight in dark areas
-
product
Handheld Analyzer
NetProbe 2000 GigE
The NetProbe 2000 GigE is the newest, state-of-the-art handheld analyzer on the market for field testing of Gigabit Ethernet services.
-
product
ATA-500UV LED Auto-Temperatured Opto-Electronic Analyzer
Hangzhou Everfine Photo-E-Info Co., LTD
ATA-500UV is a laboratory-level solution with HAAS-2000 series of High Accuracy Array Spectroradiometer as the core.The design of constant temperature system enables the system to conduct professional photometric, chromaticity and temperature testing for UV LED, which is the most ideal solution for the rapid testing of UV LED.
-
product
PDN Analyzer
The PDN Analyzer powered by CST allows you to easily resolve PDN issues as they arise in your board layout process without ever relying on a physical prototype. With digital designs continuing to increase in density and complexity, it's more difficult and critical than ever to fully understand the impact of design decisions on your Power Distribution Network (PDN) voltage and current performance.
-
product
Vibration Meter & Analyzers
Used for measuring periodic motion, to check the imbalance and deflecting of moving machinery. Specifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.
-
product
Multi-Layer Analyzers
DSL Xpert™
The patent-pending DSL Xpert multi-layer analyzer broke new ground as the only non-intrusive performance analysis solution for ADSL2Plus, ADSL2 and ADSL products. It is a modular tool designed for R&D and laboratory engineers engaged in the deployment of ADSL2Plus, ADSL2 and ADSL standard-compliant solutions. Cutting significant time from ADSL development, deployment, debugging and interoperability verification, DSL Xpert� accelerates time to market and return on investment.
-
product
Low-Mid Frequency Analyzer
LMFA-21
Amfax introduce the latest PXI based High Performance Low and Mid Frequency Analysis System operating from 100Hz TO 2MHz with an extremely low noise floor. This high accuracy measurement instrument utilizes the National Instruments Function Generator and Flex Digitizer to optimize your frequency related product performance. Using the industry standard PXI platform enables us to offer the system a fraction of the cost of other typical two box solutions.
-
product
6U Compact PCI Multiport Serial Card
CP69002
LinkedHope Intelligent Technologies Co.,Ltd.
CP69002 is designed as 6U Compact PCI Multiport Serial Card. The eight serial ports are in depended and magnetic isolated. The transform mode can be configured as RS232, RS422 and RS485 through the jumpers. The upstream interface is 32 bit 33MHz PCI bus.
-
product
SAT/CATV/TV Signal Analyzer
DSA 1491
9” full-color, high-resolution touch screen user interface simplifies complex measurement tasksRF inputs including satellite, cable and terrestrial along with ASI and IP inputsDigital RF measurements including average power/level, pre/post BER, MER, noise margin, spectral analysis and constellation
-
product
Dynamic Vapor Sorption Analyzer
IGAsorp-XT
The IGAsorp-XT is a fully automated water sorption analyzer designed for measurements at temperatures and humidities beyond those available with conventional DVS analyzers. High resolution sorption isotherms are recorded at humidity values from 0.2 %RH or lower, using the unique climate-XT control method. Combined with high temperature water sorption measurements to 300 °C, an integrated pre-heater and completely flexible method programming, the IGAsorp-XT is the world’s most advanced benchtop DVS analyzer.
-
product
VME Bus Analyzer / Exerciser
VME650
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
product
FieldFox Handheld Analyzer Software
FieldFox can be configured as a cable and antenna analyzer, vector network analyzer, spectrum analyzer, built-in power meter and much more using software/firmware functionality. All functions listed on this page can be installed at the time of FieldFox purchase or can be upgrade via a software license key. Select the functionality you need today and add more features as your needs change.
-
product
Oxygen Gas Analyzer
KM 5490
Kusam Electrical Industries Limited
• As it uses a high quality oxygen sensor, it is very precise and its performance is stable.• It uses the advance technology design and has multiple functions.• With highlight backlight display and acousto-optic alarming, it is easily configured.• The in built temperature compensation makes the meter measure the correct value of oxygen in the environment temperature of -10 ~ 40�C.• As its case is ergonomically designed, it looks elegant, and is easy to carry.
-
product
Process Hydrogen Analyzer
HY-OPTIMA™ 700B Series
H2scan’s HY-OPTIMA™ 700B series in-line, real time hydrogen-specific process analyzers are designed for ease of use, interface flexibility and true process control. The HY-OPTIMA™ 700B series is a solid-state sensor that is configured to operate in process gas streams with temperatures up to 60ºC. The HY-OPTIMA™ 700B series is ideal for hydrogen production and petrochemical applications where real-time measurements can enhance process plant efficiencies, diagnostics and maintenance management.
-
product
Gas Filter Correlation CO2 Analyzer
Model N360
Teledyne Advanced Pollution Instrumentation
The Model N360 measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360 uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
product
Transportable Gas Analyzer
CGT-7100
The CGT-7100 analyzer measures the concentration of gases in a continuous way, using a ratio photometric non-dispersive infrared absorption (NDIR) method. All pretreatment parts required for measurement, such as the pump, filter, and electric dehumidifier, are built-in. The analyzer can measure three components including CO, CO2, or CH4 (any two of these) and O2, and is compatible with measurement at 100 vol%. The CGT-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
product
JETCAL®1 Engine Analyzer
BH112JD Series
The BH112JD JETCAL® Engine Analyzer providesa superior combination of capabilities in aruggedized, portable test set.
-
product
Detective Logic Analyzer
DDR3
Provides logic analyzer like deep transaction Listing and Waveform captureCan store up to 1G of captured StatesContinuous, real time analysis, not post-processingEye Detector guarantees valid data acquisitionExtensive Triggering and Storage Qualification allows precise insightProtocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specificationsRow Hammer Analysis for potential data corruptionInteractions among up to 8 ranks, over two slots are analyzed.Mode Register Listing providedSupports Auto-Clock rate detect and clock stoppage Connects to the target under test with DIMM, SO-DIMM, and BGA interposers or a midbus probeIntegrated Microsoft Charts gives quick insight into large trace capturesTrigger In & Out allows the Detective to integrate with other test tools
-
product
Laser Spectrum Analyzer
771 Series
The 771 Series Laser Spectrum Analyzer from Bristol Instruments combines proven Michelson interferometer technology with fast Fourier transform analysis resulting in a unique instrument that operates as both a high-resolution spectrum analyzer and a high-accuracy wavelength meter. With spectral resolution up to 2 GHz, wavelength accuracy as high as ± 0.2 parts per million, and an optical rejection ratio of more than 40 dB, the model 771 provides the most detailed information about a laser’s spectral properties.
-
product
Rating Analyzer
Actus Rating Analyzer provides efficient rating and competitive analysis tools. It provides a clear graphical view of all rating information, yours and competition, along with the actual broadcast media. The clear rating and demographic data display allows you to get an easy at-a-glance information from all numbers and charts received from the rating companies. The end result is a far more accurate analysis of the content, which in turn allows research teams to give much more informative and accurate recommendations, leading to better program planning, ad placement, and even more viewers watching the shows all significantly increasing revenues.
-
product
Powerline Analyzer
SHARK 100-S
Amperis introduces one of its most advanced Sub-Meters. This high performance product is designed to measure the use of electrical energy with an accurate degree of billing and send that information by the most advanced means of communication. The unit supports RS485, Ethernet RJ45 or IEEE 802.11 Wi-Fi ethernet. This allows it to be installed anywhere in the building or construction and communicate with the Cetral Backup Software easily, quickly and automatically.
-
product
FTIR Motor Exhaust Gas Analyzer
MEXA-ONE-FT
The MEXA-ONE-FT Series simultaneously measures concentrations of multiple components, including NH3, N2O, CH4, CO and CO2, in undiluted exhaust gas using the Fourier transform infrared (FTIR) method in combination with a multivariate analysis algorithm. It incorporates HORIBA's proprietary compact interferometer which yields superior performance and high accuracy.The system complies with NH3 testing requirements of Euro VI, the EU regulation for heavy duty emissions testing.The MEXA-ONE-FT can be calibrated according to customer requirements with up to 6 component sets to cover a wide range of applications.FTIR spectroscopy allows the direct measurement of NO2 emissions and the independent quantification of individual hydrocarbon species. This makes the MEXA-ONE-FT system an ideal solution for detailed research and development tasks.Due to the measurement principle, the time-consuming daily span gas calibration is omitted.In addition, usability and flexibility are realized by “HORIBA ONE PLATFORM” which enables to extend the system with other ONE analyzers to a complete solution suitable for both certification and R&D purposes.
-
product
Memory Analysis Software for Logic Analyzers
B4661A
DDR3, DDR4, DDR5, LPDDR2, LPDDR3, LPDDR4, and LPDDR5 Analysis . The Keysight B4661A memory analysis software offers a suite of options that include the industry’s first protocol compliance violation testing capability across speed changes, a condensed traffic overview for rapid navigation to areas of interest in the logic analyzer trace, powerful performance analysis graphics, and DDR and LPDDR decoders. With the B4661A memory analysis software and a Keysight logic analyzer*, users can monitor DDR/2/3/4/5 or LPDDR2/3/4/5 systems to debug, improve performance, and validate protocol compliance. Powerful traffic overviews, multiple viewing choices, and real-time compliance violation triggering help identify elusive DDR/LPDDR system violations.
-
product
Gas Filter Correlation CO Analyzer
Model T300U
Teledyne Advanced Pollution Instrumentation
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.
-
product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
product
8 Channel Portable Spectrum Analyzer
ProCAT
# Least expensive eight (8) channel analyzer, and easiest to operate, on the market# Proprietary Damage Potential Spectrum, DP(f), mode included at no additional cost# 0.76 Hz Resolution 12,500 Line Zoomable Plots# Quad Plots - Four Active Spectrums on Screen - PSDs or DP(f)s
-
product
Circuit Breaker Analyzer
CBAnalyzer
Simple operation requiring minimal trainingVery portable - it's a laptop or tablet pc running our Windows software programNo modification of the circuit breaker is requiredNo electrical connections are requiredRemoval of the circuit breaker from its mounting or cubicle is not requiredTesting can be performed during routine switchingData is easily transmitted over the internet to the users account where it is analyzed and compared with a known good profile (KGP) for that type of circuit breaker to determine: • Overall mechanical condition • Confirm maintenance intervals and lubrication • First trip testing data for arc flash compliance • Arc flash study validation checksPerform detailed analysis and store maintenance records using CBAnalyzer suite softwareAccess to the CBAnalyzer Account Manager which: • is where user accounts are created and each user's role is designated • provides access to your equipment database and test data archives • is where tests are synced • is where your equipment data is entered and stored • is required to use the CBAnalyzer software program
-
product
Light Industrial Grade MagStripe Analyzer
Mag3x Mini
Tests wide range of cards:Encoded ID1 Plastic CardsISO tracks 1, 2 and 3Embossed / Pre EmbossedEnglish and Chinese language software availableWindows 7 BasedSimple graphical displays show pass or fail for each cardSave detailed data on each card for future analysis12-bit resolutionFast pass/fail tool for production lineConvenient, mini form factorEasy-to-use reportingServiceable by end userCalibrate at your own facilityOne click testingFast 100K samples/second
