Battery Load Testers
determine the condition of batteries to provide power.
See Also: Battery Capacity Testers
-
Product
Back and Forth Scratching Tester
WGQ-60
-
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
Product
Fiber Testers
-
The PingerPro Series provides a powerful combination of physical layer tools to troubleshoot copper/fiber links and LAN tools to identify and repair a wide range of network problems.
-
Product
Breath Alcohol Tester
-
Is kind of tester designed to measure concentration result of the breathed alcohol in the human body.This device adopts advanced flat surfaced alcohol sensor which has excellent sensitivity andreproducibility, fashional and portable design make it more convenient for personal use. When the alcohol content exceeds the preset limited level, this device would send an audio and videowarning to remind your safety.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
Shoe Heat Insulation Tester
UI-FT08
-
Shoe Heat Insulation Tester – Thermal Insulation Tester is used to test shoe heat insulation / thermal insulation against hot performance. Place the shoe in sandbath and the footwear shall contact with the plate(forepart and the heel) in certain temperature for a given period. Then to measure the temperature increase inside of the shoe. The contact temperature and time is specified in production standard.
-
Product
Spray Rating Tester
TF160
-
TESTEX Testing Equipment Systems Ltd.
Spray Rating Tester, to determine the surface wetting resistance of fabrics, which may or may not have been given a water-resistant or water-repellent finish.
-
Product
Murata Watch Battery
-
World's first mercury-free silver watch battery innovator, highly recognized as No. 1 market share manufacturer by major watch brands
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel With V/I Readback
41-752A-011
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Minority Carrier Lifetime Tester
HS-CLT
-
HS-CLT Minority Carrier Lifetime Tester has strong functions. It can not only measure carrier lifetime of wafer but also silicon ingot, silicon filament,silicon phosphorus ingot,silicon boron ingot, seed crystal and other irregular shape silicon material.The minority carrier testing ranges from 1μs to 6000μs, the minimum resistivity is 0.1Ω.cm, (can be extensive to 0.01Ω.cm). Dynamic curve monitoring in the whole process.
-
Product
General Purpose Twin-Lead Tester
69136
-
Tests voltage in 90-250 volt range, AC or DC.Neon lamp glows indicating live circuit.The 5'' (127 mm) test leads have probes on the ends.Handy pocket clip.
-
Product
LAN and telephone wiring testers
-
Measurement and analysis instruments for the deployment of telephony networks, Ethernet, and generally telecommunications networks via copper cable.
-
Product
Current Tester
MIG0624
-
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
Product
Cupping Tester
1620
-
This robust and user-friendly Elcometer 1620 Cupping Tester is used for assessing the cupping ability of coatings applied to metal sheets up to 1.2mm (0.05”) thick.
-
Product
Load Cell Tester
LCT-Ultimate
-
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
Product
Battery Pack Test Equipment For 1-2 Series Battery
TOB-W602
-
Xiamen Tob New Energy Technology Co., Ltd
1-2 Series Battery Pack Test Equipment Used For Mobile Phone Battery Performance Testing 0-10V
-
Product
Load Cells
-
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
-
Product
Specialty Testers
-
Test Products International, Inc.
TPI specialty testers offer versatility and precision to meet the needs of a variety of jobs and projects.
-
-
Product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK320A (SD Host Tester)
-
SGDK320A (SD Host Tester) is a product that has the functions of SD emulator (SD Emulator), host tester (Host Tester), SD analyzer (SD Analyzer), and eMMC analyzer (eMMC Analyzer). Supports SD Memory Card Physical Layer Specification Version 3.01. It covers the test contents of Test Specification Ver3.00 and Supplement Note. Supports SDR104 and eMMC ver4.41 (analyzer).
-
Product
Battery Module Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
This test chamber series mainly for testing the battery module of Electric-bike, Electric Motorcycles, etc. These series meet the standard compliance of IEC62619, UL2580 and GB31485-2015. Including short circuit, thermal test, drop test and crush test, etc.
-
Product
LED Tester Software
Lumeresoft
-
Evolusys Technologies Sdn. Bhd.
At the heart of the software design philosophy is the ease to create test recipe amidst the dynamic range of LED packages design & test requirements. Whether it is a single die LED, multiple die LEDs, Chip-On-Board (COB) substrate, etc. the same software can be used off-the-shelf without any special customization.
-
Product
DC Electronic Load, Single-Input: 150V, 40A, 250W
EL33133A
-
The Keysight EL33133A bench DC electronic load provides a single input and a built-in data logger. Provide static or dynamic load test up to 40 A and 150 V. Display results in a meter view or over time using the built-in data logger.
-
Product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
Product
LocoNet & Testers
-
The LNRP Xtra LocoNet Repeater Module Isolates and Protects LocoNet Layouts, it allows for greater expansion of the LocoNet system on large installations. The LNRP Xtra allows "protected" sections of LocoNet to continue functioning even when a fault occurs elsewhere, the LNRP Xtra automatically reconnects the faulty section once the issue is resolved. Now includes the PS14 power supply.
-
Product
Data Center Load Bank
-
Mosebach Manufacturing Company
Mosebach’s Data Center Server Rack load bank, the SR family, is ideal for commissioning data centers. There are multiple models for varying voltages and power levels. The unit has a variable fan speed control which allows you to fine tune as desired.
-
Product
Rod End Load Cells
-
Our rod-end load cells are designed for integration into tension measurement. They are versatile, durable, and fit easily into small spaces such as inline with vehicle tie rods.
-
Product
Bursting Strength Tester
-
TESTEX Testing Equipment Systems Ltd.
Bursting Strength Tester is used to test the strength of bursting for fabric. When you do bursting test, mullen burst tester is a wise machine for you.
-
Product
Optical Receiver Stress Testers
-
Developing next-generation optical receiver technology requires world-class stress testing. Use Keysight's automated calibration solution and get optical stressed eye results in one-tenth the time compared to a manual setup.
-
Product
Quad Channel Tester (QCT)
MS4500
-
Quad Channel Tester for Integrated Flight Control Computer (QCT-IFCC - MS4500) is a portable test equipment to check the electrical functionalities of IFCC by simulating various signals and pressure in standalone conditions. System shall simulate, acquire, monitor, and validate the functionalities of different signals.
-
Product
8K IP Camera Tester
M-IPC-750C
-
Fuzhou Metricu Technology Co Ltd
Cvbs camera test, VGA inputIP camera test, support onvif, 4K, 8K, H.264 and H.2658MP CVI, 8MP TVI, 8MP AHD camera test, support CVI 5.0 Audio test DC12V 3A, DC24V 2A and 48V / 25.5W PoE power outputAnti-sunlight and screen protecting coveruct description goes here.
