-
product
4 Slot (DD), 2U H X 290mm D, 300 Watt ATX
39C04DDA28Y3HCCX
The Type 39C is an advanced generation of CompactPCI chassis for PICMG 2.0, 2.16, 2.17, and EXP.0 applications. IEEE 1101.10/11, 6U x 160mm CPCI cards from the front and 6U x 80mm I/O cards from the rear.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Taiwan 110VAC
781630-11
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
JTAG Boundary-Scan I/O Modules
SCANIO Family
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
product
PCI, IEEE 488 GPIB Instrument Control Device for Linux
778686-01
The PCI‑GPIB is a plug‑and‑play IEEE 488 interface for PCs and workstations with PCI expansion slots. The PCI‑GPIB can sustain data transfer rates of more than 1.5 MB/s using the IEEE 488.1 three‑wire interlocked handshake. It also implements the high-speed IEEE 488.1 noninterlocked handshake (HS488) for benchmarked data transfers at more than 7.7 MB/s. The onboard bus master DMA controller means that there are no microprocessor interruptions in data transfer.
-
product
Automotive Ethernet Rx Compliance Software
AE6910R
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
Ethernet
The UNH-IOL has been providing Ethernet testing services since its inception in 1988. We have a strong and wide-reaching industry reputation and participate in many industry organizations including the IEEE, the Ethernet Alliance, and the OpenAlliance. We were honored to receive the IEEE-SA Corporate Member of the year award in 2013 for "unwavering contributions to interoperability testing of IEEE standards".
-
product
Current Transformers
The Institute of Electrical and Electronic Engineers defines a current transformer (IEEE Std C57.13) as “a transformer intended to reproduce in its secondary circuit, in a definite and known proportion, the current of its primary circuit with the phase relations substantially preserved”. Its primary winding is connected in series with the conductor carrying the current to be measured or to be controlled and its secondary winding is connected to the measuring, protection or control devices. Osborne designs and manufactures current transformers which are used for instrumentation applications, others which are used for power system synchronizing applications and others which are used in protection circuit application. They have been designed to meet specified current ratios, burden impedance and transformation errors.
-
product
Automated Stand for Magnetic Luminescent Control of Railway Wheels
The amount of information processed and time constraints required the creation of a multi-level distributed image processing system based on National Instruments Compact Vision System controllers, industrial computers and workstations. During the control process, the wheel is watered with a magnetic-luminescent emulsion, magnetized and exposed to ultraviolet radiation. As a result, the emulsion deposited on the defects glows in the visible range (yellow-green light). Eleven FireWire (IEEE 1394) color cameras with a resolution of 1280 x 1024 are used to scan the wheel surface. In one iteration, they completely cover a 20-degree sector of the wheel.
-
product
802.11a,b,g RF Shielded Test Enclosure
JRE 0814-A
Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.
-
product
Special / Customer Spec. Crates
6U VME64x 6023 JLAB Crates
For the Thomas Jefferson National Accelerator Facility (JLAB) in Virginia (USA), a special version of the VME 6023 crate series with front to rear air-cooling was developed. “JLAB style” VME crates are available with standard VME/VME64 backplane and mechanics as well as with VME64x or VXS (see VXS section) backplane and IEEE 1101.10 compatible mechanics, (enhanced EMC and ESD shielding).
-
product
GPIB General Purpose Interface Bus
The design of the GPIB control card is fully compatible with the IEEE 488.1 and IEEE 488.2 standards, using the PCI interface, supporting the Plug & Play specification, and supporting Windows 95/98/Me /NT4.0/ 2000 /XP/7 Operating system, driver function library includes Windows development software tools such as Visual C++, Borland C++ Builder, Labwindows, Visual Basic, Delphi and Labview. This GPIB-supported library provides an NI-like command control syntax format, which is convenient for users to develop and transfer applications smoothly. This interface card also provides a conversational window GPIB interface program, which is convenient for users to directly control the instrument without writing a program.
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Windows, Low Profile
780575-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
JTAG based Test & Flash Programming Services
We offer EMS companies and design houses services and solutions in manufacturing testing with bias towards JTAG (IEEE 1149.x Boundary Scan) and functional test: System-level DFT rule checking for production testing and inspection. Test strategy development and optimization for test cost reduction. JTAG, functional, and emulation-based test development and deployment. Product testing and troubleshooting services. Ultra fast in-system programming solutions (Flash, EEPROM).
-
product
Certified Solutions
Advantech has several certified products for the railway automation or power & energy automation, such as IEEE 1613 controllers, EN50155 switches and IEC 61850 substation controllers. All these certified solutions are for the transportation or power & energy industries. The certified products are verified by individual third party organizations to help your system work more reliably in substation automation applications. EN50155 certified solutions, including EN50155 switches, are designed for passenger information system, the IEC 61850-3 and IEEE 1613 certified solutions, such as IEC 61850 substation controller and IEEE 1613 controller, are suitable for substation automation and wind power grid automation, the Det Norske Veritas (DNV) certified solutions which are integrated with ECDIS, are ideal for navigation applications. The certified solutions Advantech offers means engineers can create reliable and safe working environments.
-
product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,4 m
763061-03
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
product
Non-steady-state probe for thermal conductivity measurement
TP02
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
product
Paragon-One
Focussed PTP Test Options. Specific feature bundles delivering test solutions for PTP to profiles such as IEEE 802.1AS/AS-REV, SMPTE 2059-2, and ITU-T G.8275.1
-
product
Multifunction Data Collection and Analysis System
9000
The Model 9000 DME System is a high performance multifunction data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER), Digital Fault Recorder (DFR), Dynamic Disturbance Recorder (DDR), and Continuous Recorder data in conformance with PRC-002-1 and PRC-018-1. All data recorded by the DME system is stored in IEEE C37.111 format and named in conformance with IEEE C37.232. The system also has a software option to enable the Phasor Measurement Unit (PMU) feature to provide streaming data in conformance with IEEE C37.118.
-
product
Industrial Ethernet
PLANET Industrial Ethernet equipment is compliant with various industrial protocols and ITS certifications such as MQTT, Modbus, SCADA, EtherCAT EN50155 and E-Mark to meet all the transmission needs, be it Information, Control or Device. PLANET features ERPS Ring, IEEE 1588 PTP, Layer 3 routing, 10G transmissions, cybersecurity and more to ensure high performance and security of our comprehensive Industrial Ethernet collection.
-
product
PXI GPIB Instrument Control Module
PXI GPIB Instrument Control Modules feature IEEE 488 controllers for PXI systems. You can choose an option that supports Gigabit Ethernet transfer speeds. PXI GPIB Instrument Control Modules include a license for the industry standard NI-488.2 driver software enabling reliable connections to third-party instruments with GPIB.
-
product
CABLE ASSY,TYPE X2,5M
763061-05
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
PoE Injectors, Splitters and Extenders
Advantech's fiber & PoE converters, injectors, splitters, and extenders are designed to provide network operators support for Mega PoE IEEE 802.3BT
-
product
Digital Panel Mount Load Cell Meter
MODEL DPM-3
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
product
Battery Capacity Tester
BLU-C Series
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
product
Premanaged Gigabit Ethernet Switch
XES-2T6
The XES-2T6 is a six plus two port Gigabit Ethernet switch with two ports being aggregated to a high throughput, redundant trunk link. The six other ports are individually assignable to groups (IEEE 802.1Q VLANs) that may participate in completely independent networks that do not interfere with each other. Thanks to the graphic OLED display, the encoder knob and a push button for each of the six configurable ports, the switch is intuitive to setup and the configuration is done in next to no time.
-
product
GPIB-RS232, Instrument Control Device
779732-12
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - China 220VAC
781630-10
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
