High-Speed Digital I/O
-
Product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
Digital I/O Module
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
64-Channel Boundary-Scan Digital I/O Scan Module
JT 2111/MPV DIOS IDC
Digital I/O Module
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
Product
Digital I/O Board
3512
Digital I/O Module
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-2IPC-6U
Digital I/O Module
The CPCI-2IPC-6U module provides a high performanceflexible I/O scheme, that supports industry standard IndustryPacksÔ. For application requiring high performance, highdensity I/O or unique combinations, the CPCI-2IPC-6U is theperfect solution. The Local DSP’s can be used to simplymove data to and from the CPCI bus or provide localprocessing functions such as local PID controls, FFT’s, digitalfiltering, etc.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (32-in/32-out LVDS, 8 SE, KU035)
787280-01
Digital I/O Module
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
Digital I/O Module
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
Digital I/O
Digital I/O Module
ADLINK digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports up to 256-CH high-density on a single board, making them suitable for I/O status monitoring and ON/OFF control applications.
-
Product
80 I/O Multifunction Module
YAV90832
Digital I/O Module
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
Digital I/O Module
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
Product
PXI Opto-Iso Digital I/O 32bit out 16bit in
40-490-002
Digital I/O Module
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
Product
Non-Isolated Digital I/O DAQ Cards
Digital I/O Module
PCI/PCIe-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, and logic signal sensing.
-
Product
PCI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated Digital I/O Device
778970-01
Digital I/O Module
The PCI-6513 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI 32 Channel I/O Serial I/P Prog Threshold
40-412-001
Digital I/O Module
The 40-412 is a 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels
-
Product
Industry Pack Carriers and Digital I/O
CPCI-IPC
Digital I/O Module
The CPCI-IPC module provides a 3U high performance flexible I/O scheme, that supports industry standard Industry Packs™. For application requiring low cost, high density I/O or unique combinations, the CPCI-IPC is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSP via the CompactPCI bus. A very low cost, non-intelligent version is also available, CPCI-SIP.
-
Product
PCI-6503, 24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device
777690-01
Digital I/O Module
24-Channel, 5 V, TTL/CMOS, 2.4 mA Digital I/O Device - The PCI-6503 uses a 24-bit programmable peripheral interface (PPI). Each interface is Plug and Play compatible and does not require a separate card manager for configuration. The PCI-6503 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment.
-
Product
PCI-6516, 32-Channel, ±30 V, Source Outputs, Bank-Isolated Digital I/O Device
779082-01
Digital I/O Module
The PCI-6516 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6516 module is an industrial digital I/O interface, with all channels on an isolated bank. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6516 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 48-Channel
42-419-002
Digital I/O Module
The 40-419-002 (PXI) and 42-419-002 (PXIe) are a 48-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Industrial I/O Module
DIO-3460
Digital I/O Module
The DIO-3460 is a space-saving industrial I/O module. It provides for save cable connections due to the use of WAGO Cage Clamp connectors rather than screw terminals.
-
Product
Digital IO
PA32IX
Digital I/O Module
The PA32IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32IX also supports deep pattern memory by offering 64 M of on-board vector memory with static per pin direction control and with test rates up to 50 MHz.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (64-in LVDS, 8 SE, KU060)
787282-01
Digital I/O Module
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
Digital I/O Module
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
USB-6501, 24-Channel, 8.5 mA, Digital I/O Device
779205-01
Digital I/O Module
The USB-6501 is a portable, bus-powered USB digital I/O device, providing reliable data acquisition and control at a low price. The device provides overvoltage protection its digital I/O lines and a 32-bit counter. With plug-and-play USB connectivity, the USB-6501 is simple enough for home and academic applications, but robust and versatile enough for laboratory and industrial applications.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.447-16
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Multi-Channel, 14-Bit Digitizer
ADQ14
Digitizer
ADQ14 is a 14-bit digitizer family with 1, 2, or 4 channels and 0.5, 1, or 2 GSPS sampling rate. It is also available with either AC or DC coupling (ADQ14AC and ADQ14DC) and comes in six different form factors. This simplifies integration and enables cost-efficient system-level design.
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe Digitizer: 4 Channels, 2 GHz, 12-bit
M5200A
Digitizer
The M5200A is a single-slot PXIe four-channel, high-speed, analog to digital digitizer. It is a high-performance digitizer with easy-to-use programming libraries, real-time sequencing technology, and FPGA programming.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 24 Channels
DN6.593-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 40 Channels
DN6.592-40
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PCIe 16 Bit Multi-Purpose Digitizer - up to 80 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5943-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
C Series Digitizer Module
Digitizer
The C Series Digitizer Module takes both high-speed and high-resolution time- and frequency-domain measurements. It features up to four channels that can sample at speeds up to 20 MS/s—ideal for discrete detection of signals 10 MHz and smaller for applications such as fault detection, partial discharge analysis, and acoustic measurements. The module's store-and-forward architecture allows up to 128 Mbits of measurement data to be sent back to the CompactRIO Controller and analyzed. You can use the module as part of a CompactRIO system and use the LabVIEW FPGA Module to develop an advanced trigger based on low-speed streaming for added flexibility. This digitizer includes the NI-DAQmx driver and configuration utility that simplifies configuration and measurements. NI-DAQmx supports NI programming environments and Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
