Ground Testers
-
product
Tribocorrosion Tester
ASTM G119
Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.
-
product
Wire Abrasion Tester
SG-D03DG
This machine is mainly based on UL1581 / UL83 standard abrasion test wire and cable testing requirements .
-
product
GFCI Socket Tester
TEL5
Standard Electric Works Co., Ltd
● Fast, easy wiring check.● Easy to read light indication.● Confirm the correct wiring of AC socket.● Test GFCI for correct wiring & operation.● Detect 5 wiring faults.● GFCI circuit trips to confirm the tester is working.● The testing current for GFCI is about 8mA.
-
product
Leakage Current Tester
2675
Shenzhen Chuangxin Instruments Co., Ltd.
RK2675 series Leakage Current Tester is used to measure the electrical insulation quality and products’ safety performance of the main indicators.
-
product
Field Ground Module
SEL-2664
Schweitzer Engineering Laboratories, Inc.
Add the SEL-2664 Field Ground Module to the SEL-300G or SEL-700G to protect all the critical components in your generator with one comprehensive relay. Or, add the SEL-2664 to the SEL-2664S to complete ground fault protection on both the rotor and stator.
-
product
Phase And Continuity Tester
4100A
Peaceful Thriving Enterprise Co Ltd
There are two function of this tester. One is to test the continuity and the other one is to test the phase of three-phase system. The operation is easy, the indication is clear with LED indication. There is a loud buzzer to remind you the continuity. The illumination is very helpful in the dark environment.
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
CABLE TESTER
MCT-7
Whirlwind Music Distributors, Inc.
This diagnostic cable tester has connectors for analyzing almost any type of cable combination. The convenient rotary switch allows testing of each conductor within the cable and can determine the internal wiring configuration. Tests NL4, 5 pin DIN, BNC, XLR, TRS, RCA and 3.5 mm types.
-
product
Ground Resistance Tester
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
product
Damp-Heat Tester
King Design Industrial Co., Ltd.
1. Technical index:*Power: 380V, 3-, 50/60HZ 110A*Temperature range: 50°C~120°C*Humidity range: 20%~95% RH*Accuracy: 1) temperature ± 0.3°C;2) humidity ± 2.5% RH*Uniformity: 1) temperature ± 2.0°C;2) humidity ± 3.0% RH*Uniformity test: measured at T=85°C, RH=85%; set 9 points for temperature measurement and 2 points for humidity.*Inner wall is above 50 cm; within 20 min after temperature/humidity meets the setting value, the distribution uniformity of temperature/humidity can meet the aforesaid requirement.
-
product
30KV-100KV AC/DC Hipot Tester
2674
Shenzhen Chuangxin Instruments Co., Ltd.
30KV-100KV AC/DC Hipot Tester
-
product
Solenoid Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
product
Computer Safe Circuit Tester
24550
Safe for automotive computers. Won’t damage sensitive electronic components. Draws less than 21 mA. at 12 volts DC. Operating range 3-28 volts. The red light indicates positive polarity, green indicates negative polarity.
-
product
12-bit, 4 Analog Current Outputs With Separate Grounds, Optically Isolated 500 V
APCI-3504-C
4 analog current output channels with 500V optical isolation, 12-bit resolution, each output has its own ground line.
-
product
Rope Testers
The LMA Signal measures loss of metallic cross-sectional area (LMA) caused by corrosion, abrasion, etc. The LMA Signal is quantitative and can be calibrated. (Typically, a rope must be retired when the LMA exceeds 10%).The WRR Signal measures wire rope roughness (WRR). WRR is defined as the aggregate surface roughness of all wires in a rope. WRR is typically caused by and indicates internal and external corrosion pitting, broken wires and clusters of broken wires. The WRR signal is quantitative, and it is calibrated together with the LMA Signal.The LF Signal can indicate localized flaws (LF), for example, broken wires, corrosion pitting, etc. Because it is only qualitative - and cannot be calibrated - it is of limited value for assessing rope deterioration and for making rope retirement decisions.
-
product
Auto Bursting Strength Tester
TF142A/B
TESTEX Testing Equipment Systems Ltd.
Auto Bursting Tester, to determine the bursting strength of fabric, woven or knitted fabrics, non-woven, paper and board by the Application of hydraulic load under a rubber diaphragm of a specific area.
-
product
Non-Contact Voltage Tester
NCVT-1
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
product
Circuit Tester Set
TE6-0719
Hangzhou Tonny Electric & Tools Co., Ltd.
*Needle point probes*Continuity tester requires one AAA battery, battery not included
-
product
Glow Plug Tester
The analyser test the condition of the glow plug in diesel engines and it comes with a graphical display without any language it shows the actual resistance of the glow plugs with conclusive result after the test. The analyser will switch off automatically if the tool is not being used, to conserve battery life. The tester comes with a built-in torch light to light-up dim surroundings for finding the glow plug or other car electrical problem.
-
product
Portable Force/Displacement Tester
The FSA-MSL Mini Material Tester is a portable force/displacment tester. The FSA-MSL is ideal for tests requiring very small movement, like switch tests. The tester also features a reversible base plate, allowing the tester to be used on uneven or obstructed surfaces. The highly visible EL display and plain language menus in eight languages make programming fast and easy. Both force and displacement values are displayed plus user-selectable data; high/low setpoints, peak, memory data, etc.
-
product
Volt Probe & Socket Testers
Non-Contact & Socket
Use Amprobe non-contact volt probes to safely check circuit breakers, wall sockets and fuses for voltage presence with portable, economical tools. For sockets, choose an Amprobe socket tester, which can confirm whether GFCI breakers are properly wired.
-
product
Incline Impact Tester
Evaluates the ability of the packaging system to withstand sudden horizontal impacts or crushing forces.
-
product
Horizontal Flammability Tester
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
product
ADT-01 Primary Adhesive Tester
Jinan Leading Instruments Co., Ltd.
ADT-01 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
product
Battery Tester
TMC-2001RTS
The TMC-2001RTS is our newest member of advanced battery testers. We integrated in a very small and lightweight housing all facilities for modern battery and UPS maintenance. Best price/performance ratio.
-
product
Advanced Loss Tester
OLT-55
ated with Stabilized Laser Source, Optical Power Meter, Optical Loss Tester, ORL Tester and Length Testing functions. It can perform automatic bidirectional loss test on single fiber with Pass/Fail assessment. With rich functions, flexible configuration and excellent user friendly design, OLT-55 is the ideal optical loss tester to completely evaluate the optical fiber link condition in FTTx, LAN and CATV network.
-
product
Signal Light for Hipot Testers
LX-signal light-HV1
2-color indicator light, red, green.With the help of the signal light tower, you can visualize potentially high voltage.
-
product
Insulation Tester
Cambridge Instruments & Engineering Co.
'CIE' Insulation Tester is a compact portable unit incorporating most modern features used for direct reading of electrical operating machines, Rotating Plant equipment, Stationary apparatus, Insulation Control switching equipment, Distribution networks, Communication cables, Insulators, Transformers, Industrial Installations, Cable, electrical components, wiring and other devices capable of carrying the rated voltages.
-
product
Radiant Imaging Tester
Lumere-ZeM
Evolusys Technologies Sdn. Bhd.
• CIE matched color filters and neutral density filters• Wide range of working distances and aperture settings• Color and light measurements
-
product
Impulse Tester
MIG2412SPD
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.





























