Ground Testers
-
Product
Lithium Battery Equalization Tester
LIFG
-
Fuzhou Fuguang Electronics Co., Ltd.
The LIFG series Tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem that inconsistent voltage of lithium battery pack. Meanwhile it supports to make the voltage difference of any battery, which can be used for research and development experiments to stimulate what problems will occur when the battery reaches the maximum voltage difference under harsh work working conditions.
-
Product
DC Resistance Tester
GDZRS-20A
-
GDZRS series Winding DC resistance tester is optimal designed for measuring three phase winding DC resistance of big capacity transformer. It can test three phase winding DC resistances at the same time
-
Product
Digital Insulation and Continuity Tester
Metra Insu 20
-
Measurement of the insulation resistance on electrically dead equioment and systems with test voltages up to 1000 V. For testing motors, transformers, generators, switchgears. For testing of house hold appliances. Measurement of the insulation resistance of cables. Very useful for on-site maintenance and service departments.
-
Product
Ground Penetrating Radar Utility Locator
PinPointR
-
The ImpulseRadar PinPointR offers a clear and dependable way to quickly and easily locate, avoid or map underground utilities with the functionality required to meet approved industry standards, whilst offering market-leading performance and data quality.The enhanced bandwidth of the PinPointR antenna provides resolution beyond that of any single-channel GPR system for the detection of near-surface utility targets and other internal reflectors of interest, as well as deeper utility targets with maximum depth penetration.Key features:- RTS-based Antenna technology- Dual-channel operation- Android-driven interface- Wireless data acquisition- Integrated GPS, with external GPS support- No survey speed limitation
-
Product
FPD Tester Signal Module
A040209-05-04
-
A040209-05-04 is a MIPI signal module board and complies with the MIPI DSI v1.2 / MIPI D-PHY v1.1 signal specifications and standards. A040209-05-04 is used with the FPD Tester and can be applied to MIPI Display testing, providing MIPI Panel standard signal and other related controls.
-
Product
6-24V Car Circuit Tester
1953
-
Peaceful Thriving Enterprise Co Ltd
Check on 6-24V system. The alligator (earth) clip is suitable earth and the tip of the contact probe is placed onto the part to be used. If current is present the test light will glow.
-
Product
Mini Lan Tester
21-8572-00
-
Auto decipher the straight and cross-over pinning?RJ45 each pair connected display.
-
Product
Emission Testers
-
Maschinenbau Haldenwang GmbH & Co. KG.
A device that monitors the composition of the flue gas of a boiler heating unit to determine if the mixture of air and fuel is at the proper ratio for maximum heat output.
-
Product
Rugged Igniter Tester
4314 KV
-
Model 4314 KV is a 4-wire ohmmeter designed to use low test currents for its measurement. Additional circuitry proprietary to Valhalla Scientific is used to ensure that test current levels do not exceed the specified “fail-safe current” even in a worst-case component failure situation.
-
Product
Instrumented Indentation Tester
-
With Anton Paar’s versatile indentation testers you can precisely determine the mechanical properties of thin films, coatings, or substrates such as hardness and elastic modulus. The instruments handle almost any type of material, whether soft, hard, brittle, or ductile. You can also conduct creep, fatigue, and stress-strain studies on surfaces in the nanometer range.
-
Product
Bottle Cap Torque Testers
-
NJY Series Torque Tester is designed to measure the open force and lock force of the caps of bottles, spout bags and flexible tube packages.
-
Product
CAN, CANopen, J1939 Tester
X-Analyser3
-
Warwick Control Technologies Ltd.
Graphical User Interface ideal for Windows PCs and tablets.• CAN, J1939, NMEA2000, CANopen, LIN and OBD – included into one tool• On-Board Diagnostics Scan Tool Features for Emissions ECUs.• CAN and LIN signal reverse engineering• Signals displays – text, scope and graphical such as gauges and lamps• Can be used for ECU or even network simulation• SAE J1939 database integrated with over 4000 PGNs and signals
-
Product
Non-Contact Voltage Tester
1LAC II
-
The Fluke 1LAC II Non-Contact Voltage Tester is easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
Product
Rubber Testers
-
TA Instruments introduces a complete line of new instruments for the measurement of rheological and physical properties of polymers, rubber and rubber compounds at all stages of manufacture. The new rubber testing instruments include a Rubber Process Analyzer, Moving Die Rheometer, Mooney Viscometer, Automated Density Tester and Automated Hardness Tester.
-
Product
Battery Tester
B6720
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
*No test leads needed*Easy-to-read color scale *Self powered-no need of battery *1.5V=AAA,HP16,MN2400,RO3 AA,HP7,MN1500,UM3 C,HP11,MN1400,SP11,LR14,LM2 D,HP2,MN1300,SP2R20,UM1 9V Battery,6F22
-
Product
Micro Vickers Hardness Testers
HMV-G Series
-
This micro hardness tester features a built-in CCD camera for standardized automatic length measurement. Hardness can be measured simply and accurately with easy-touse PC software. The lineup also includes fully automated (FA) machines equipped with an electrically driven revolver mechanism and electrically driven XYZ. A manual machine with an optical head and models with color cameras are also included in the lineup.
-
Product
Fuel Injection Pressure Tester
33900
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
Product
Pro CABLE TESTER
PK-101/PK-101C
-
PK101 is an innovative tester to perform full cabling testing, displaying wiremap, cable ID, faults, toning and identify active network port on all common low-voltage cabling system in today's automated homes, network, telephone or video media, and determine cable run length up to 300 M.
-
Product
RCD Testers
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
-
Product
Speedometer/Taximeter Testers
-
Machines for checking the accuracy of speedometers, taximeters, speed limiters, speed warning devices. As with most VLT equipment, these machines can be used stand-alone, or in an integrated test lane.
-
Product
Programmable Insulation Resistance Tester
2679
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable insulation resistance tester Feature Resistance test range: 2512: (1µΩ—2MΩ nine shift) Variable speed test:5times/slow,10times/fast. Test accuracy:0.02%±2digits。
-
Product
Compression Testers
-
Dedicated compression testers offer low footprint test systems. Lever operated systems allows for quick and repeatable compression testing. The wheel operated system allows for more precision with hand wheel operation. The motorized compression tester allows for the most control and the highest degree of repeatability with the ability to set a constant test speed.
-
Product
Wire Crimp Testers
-
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
Product
Installation Testers
-
A Multi-Function installation tester is better then the single function meter. Good quality insulation, a properly working grounding system and active protection assure the safety of people, electrical systems and buildings, and protect them against electrocution, fire and other equipment damage and all of this can be checked by an HT Instruments Installation tester
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Automated Multi-Functional Tester
QTouch 1408 C
-
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
Product
Air Leak Testers
-
Leak testing is an important quality control test in the manufacturing industry. Since there is no such thing as a completely leak-free component, the key is to determine what leak rate is acceptable in order to manufacture products that are safe and adequate for the customer’s needs. Once the consequence of a leaking product is determined, it can help guide what type of test method is most practical based on budget and technology required to perform testing at the determined specifications.
-
Product
Multi-Battery Tester
MBT-MIL
-
The ZTS MBT-MIL Multi-Battery Tester (MBT-MIL) provides a comprehensive means of testing the state of charge or state of power for more than 30 battery types. This microprocessor-controlled instrument is designed to test popular primary (non-rechargeable) and rechargeable batteries using a patented, high accuracy pulse load test. After a fully automatic test cycle, percentage of remaining battery capacity is indicated on the LED bar display.
-
Product
Build Your Hydrostatic Tester
-
Start with the basic Model 9901 hydrostatic tester as shown to the left with the following standard equipment:- Hydrostatic test pump, air operated.- 1% ANSI B40.1 Grade 1A stainless steel high pressure gauge.- ANSI B40.1 Grade B air pressure gauge.- Micro adjust precision regulator.- High pressure isolation shutoff valve.- Automatic lubricator.- Stainless steel high pressure manifold.- 1/4" NPT accessory port.- Bleed valve.- Air shutoff valve.- Factory set air pressure relief valve.- 7/16-20 straight thread O-ring boss outlet port (MS33649-04) with -4 male adapter fitting.- 3/4" swivel female hose inlet with strainer.- Stainless steel base plate with rubber feet.
