Polarization Meter
Measure the polarization of transverse waves.
-
Product
Current Clamp Meter
CP 41
-
The CP 41 current clamp meter has been designed for reliable and accurate, non-intrusive measurement of AC, DC and complex waveform currents. Using advanced Hall Effect technology the CP 41 can measure currents accurately from 5mA to 40Amps.
-
Product
Digital Sound Level Meter
Model KM 926
-
Kusam Electrical Industries Limited
KM 926 designed according to the IEC 651 TYPE 2 & ANSI S1.4 TYPE 2 for sound level meter. Instantaneous sound measure function. Measurement Range : 30 ~ 130decibel. With two equivalent weighed sound pressure levels, A & C. Fast & Slow dynamic characteristic modes. AC & DC signed output for frequency analyzer level recorder, FFT analyzer, graphic recorder etc.
-
Product
Surface Resistance Meter
WL MIDGET
-
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
Product
Bench Meters
LCR Meters
-
The measuring objects of LCR Meters are the parameters of impedance components, including resistance R, inductance L, quality factor Q, capacitance C and loss factor D. The selection of digital bridge should consider the highest frequency, test accuracy, test speed and DCR test function of the tested device.
-
Product
Meter Test Benches
Test Station
-
The meter test station allows simultaneous testing of 3, 5, 10 or 20 induction or static electricity meters. The test station could be constructed for single-phase electricity meters or for three-phase meters.
-
Product
Clamp Meter
ECLIPSE
-
ECLIPSE has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp is provided with a display with 6000 measuring spots with backlight and bargraph to allow for a simple reading even in poorly lit environments.
-
Product
Energy Detector Laser Energy Meters
11QE25-LP-S-MB
-
11QE25-LP-S-MB energy detector provides a unique combination of high damage resistance and high speed. It also offers very good linearity with power and a versatile mounting system. It is right for many pulsed lasers. It is right for many OEM, manufacturing and laboratory uses.
-
Product
S Series Panel Meter
ST-100
-
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 50A● Case and Composition: Acrylic resin front and Bakelite case. Four studs mounting.● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate.● Pointer：Tube or knife-type, color in black or red.
-
Product
Polarization Instrumentation
-
This page features the optics and instrumentation necessary to control and measure the polarization of light. Our free-space and fiber-coupled polarimeters can measure any state of polarization (SOP) on the Poincaré sphere.
-
Product
Power Meters and Sensors
-
Anritsu offers the world's most comprehensive range of power meters. The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements (e.g. radar), while the ML2480B series is suited for Wide-band power measurements on signals such as W-CDMA, WLAN, and WiMAX.The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package.
-
Product
Magnetic Field Meter
MP-1000
-
The List-Magnetik MP-1000 magnetic field meter is equipped with externally connectable transverse and axial field probes, making it easy to carry out precise magnetic field measurements. This versatile device is ideal for measuring direct, alternating (true RMS), and pulsed fields, making it suitable for a wide range of magnetic field measurement applications. It is also ideal for measuring residual magnetism.
-
Product
PH/ORP, Conductivity, Oxygen & ISE Meters
-
As one of the leading brands for laboratory and field measuring instruments, WTW develop solutions that are used worldwide in drinking and waste water treatment, environmental monitoring, research and industry. The portfolio ranges from high-precision benchtop meters for the laboratory to robust handheld meters for mobile use and complex multi-parameter systems. Whether pH value, conductivity, dissolved oxygen or ISE - our devices deliver reliable and standard-compliant results even under the most demanding conditions.
-
-
Product
Benchtop DO/BOD Meter
LAQUA DO2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
4 Digit Temperature Meter (5 Channels)
CM1-TX5
-
RS-485 Modbus RTU protocol (with communication LED indicator)RS-485 address 1~255Communication Baudrate 9600, 19200, 38400, 57600, 115.2KParity check N81, N82, E81, O81Input 5 channels of signal selectable：thermocouple/PT100.5 channels of input can be set to play 1~10 seconds loop display.1~5 channels of display value limits can be set, and the number of channels of carousel display screens can be set by yourself.5 channels of input signals with LED unit cycle display.Standard 2 groups of alarms Hi, LO with communication LED indicators to ensure the normal operation of the field system.Suitable for HVAC refrigeration and air conditioning PLC, DDC, PC brands to achieve remote real-time monitoringCan be used in solar panels, medical control, clean room, ice water host, boiler, motor, chemical plant, power plant, school energy-saving control, remote control of power monitoring panel
-
Product
Light Meters
-
Our light meters are designed for simple and accurate results in an industrial setting. Whether you are checking work spaces, parking lots, or baseball fields for safe levels of lighting or measuring for testing design compliance, a light meter from Sper Scientific will get the job done. Obtain precise UV, FC or Lux measurements, in multiple light measurement ranges. These light meters are designed for use in work spaces, labs, schools, outdoor studies, optics, home inspections, and many others. In addition, you may use these meters to check compliance with ANSI/NFPA 101 (standards for emergency & exit lighting).
-
Product
Optical power meter with Optical laser Source
-
Shanghai Baudcom Communication Device Co.,Ltd.
The Multimeter combines a power meter with a 2-wavelength laser source,for optical fiber network installation and maintenance. With the large capacity of data storage,it's very convenient for field testing and transfering the test results to PC through USB interface.
-
Product
Reverse Osmosis Meters For Measuring Total Dissolved Solids
RO Meters™
-
The choice of professionals for years, this compact instrument has been designed specifically to demonstrate and test Point of Use (POU) reverse osmosis or distillation systems. By measuring electrical conductivity, it will quickly determine the parts per million/Total Dissolved Solids (ppm/TDS) of any drinking water.
-
Product
Multiplex Optical Maintenance Meter
LS280
-
LS280 is used to measure optical maintenance factor for high power LEDs, LED module, LED bulb or other LED luminaries. It is the important measuring equipment for performing the reliability of illuminants. • Freely set the time interval and time extent for automatic measurement • LCD Display, connect with PC via RS232 and English version software. • The test results can export Excel or PDF format and easy to compare. It can be saved by LS280 software or by USB directly. • The engineer can do LED life analysis based on the LS280 test results. • LS280 worked with High Power LED Aging Test (LS600), Multiplex LED Temperature Test (TMP-8/TMP-16) and High and Low Temperature & Humidity Chamber (GDJS-*B), it can do Flux VS Temperature VS Time, which is a perfect instrument system to meet LM-80 request.
-
Product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
-
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
Product
Ultrasonic Energy Meter
Series TUF
-
The SERIES TUF Ultrasonic Energy Meter is a highly accurate and stable energy meter that utilizes ultrasonic technology to measure heating and cooling energy consumption. The Series TUF is a compact meter with a flowmeter and energy calculator in one, making it great for installation on chillers and boilers.
-
Product
DIGITAL TV LEVEL METER
1500series
-
The optimal signal analyzers to test and measure both analog/digital signals. Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the TV broadcasting signal.
-
Product
PRO pH Meter
MW100
-
The Milwaukee MW100 PRO pH meter features manual calibration and fast operation in a rugged design. The Milwaukee MW100 PRO pH Meter is ideal for users in pools, and hydroponic applications. This meter is also ideal for educators that want their students to learn the basics of pH meter calibration before going fully automatic.
-
Product
Spectral Light Meters For Photometric And Colorimetric Measurements
-
Comprehensive range of spectroradiometers for the measurement of illuminance (lux), luminance (cd/m²), luminous flux (lumens), luminous intensity (cd) as well as the colorimetric characteristic values such as chromaticity coordinates (x,y,u',v') or color rendering index (CRI), etc.
-
-
Product
Flow Meter / Monitor
NivuFlow Mobile 600
-
The NivuFlow Mobile 600 was developed particularly for long-term measurements in field operation without external power supply. Measurements for checking and verifying can be carried out with the self-sufficient and portable system without any problems even in harsh environments. Battery lifetimes of several weeks or even months reduce personnel costs for maintenance and data readout significantly.
-
Product
Data Logging Class 2 Sound Level Meter
Castle Sonus GA216L
-
The Sonus GA216L Sound Level Meter is a fully compliant, integrating and data logging instrument, capable of a wide diversity of applications including Noise at Work and Environmental Noise monitoring.
-
Product
Power Meter
TW3211
-
Techwin(China) Industry Co., Ltd
TW3211 optical power meter Is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optical fibers. A Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, a wide range of power measurement, high accuracy, an user self-calibration function and a reference power level storage.
-
Product
Handheld Optical Power Meter
JW3208
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3208 handheld optical power meter is a compact and an easy-to-use testing instrument for optical fiber networks, which can be used for absolute optical power measurements as well as for relative loss measurements in optical fibers. It features ingenious appearance, wide range of power measurement, high accuracy and user self-calibration function with high performance-to-price ratio.
-
Product
4 2/3 Digital Resistance Meter
CS2-RS
-
CS2-RS Resistance Indicator has been designed with high accuracy measurement, display and communication of Ohm (2 wire) as like as Coil of motor or transformer.The meter supports Field Calibration function. It can be calibrated with sensor (Resistance) to meet machinery structure.We build flexible function as like as 3 bank (for multi-range scaling and set point) and 3 external control inputs meet to various testing equipment inquiry.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments applications.
