Mechanical Fixtures
Use cams or levers to bring UUT to contacting elements.
See Also: Fixtures, Test Fixtures, Vacuum Fixtures, Pneumatic Fixtures, Manual Fixtures
-
product
Manual Fixture Kit
230354 – CMK-05
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
-
product
Dual Servo Electrical Test Fixture
TA-334001
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
-
product
Test Fixture Adapters for In-Circuit Test Fixtures
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
product
Test Fixtures
REINHARDT System- und Messelectronic GmbH
Is a fixed state of a set of objects used as a baseline for running tests. The purpose of a test fixture is to ensure that there is a well known and fixed environment in which tests are run so that results are repeatable.
-
product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
product
Manual Fixture Kit
230356 – CMK-07
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Precision mechanical switches
Precision mechanical switches
Often copied but never matched: With a repeat accuracy of 1 micrometer, My-Com has undisputedly been the world's most accurate and compact mechanical limit switch since 1967. Innovative developments have enabled it to be increasingly more reliable wherever it is used. To date, My-Com has proved its impressive reliability in over a million applications.
-
-
-
product
Manual Fixture Kit
230376 – CMCSK-07-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
System Test Fixture
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
product
CMP Mechanical Kits
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
-
product
Burn-In Test Fixtures
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
product
Through Connector Functional Test Fixtures
Circuit Check is a pioneer in the development and implementation of access mechanisms enabling testing of circuits through on-board connectors.
-
product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 250 mm (wxd)
CMCSK-03-01
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
product
Standard RF Fixture
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
product
Spring Clip Fixture
16092A
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
product
Precision LCR Meter With Component Fixture And Limits Comparator
LCR400
0.1% basic measurement accuracyDual 5 digit high brightness displaysAutomatic component recognitionBuilt-in 4 terminal component fixtureLimits comparator with 8 Pass bins plus 2 Fail binsThree test frequencies, switchable biasRS232 interface standardOptional SMD tweezers, BNC connectors, Kelvin Clip test lead set, and PC logging software
-
product
Mechanical Stress Card Testing
Wheels are transversely positioned with micromechanical stopsPressure exercised on the card's chip and microcircuitryThe card is free to deform in the Z axisThe stress is controlled by an accurate, precise force sensorProgrammable number of cycles
-
product
Mechanical Force Gauges
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
product
Automatic Fixture Removal
S96007B
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
-
product
Accessories For Instruments And Fixtures
N1254A
The N1254A includes several optional accessories and adapters for instruments.
-
product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
