-
Product
Waveguide Loads
-
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
Product
RF Plasma Generators
-
Choose from a broad range of RF plasma generators and access unique features for configuration, control, and application requirements. From various mounts and sizes to full digital control and plasma dynamic response, our RF generators can ignite your process innovation.
-
Product
LXI 50Ω RF Matrix - 2.4GHz
-
Pickering's LXI 50 RF Matrix - 2.4GHz design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output. These matrices can be supplied in a variety of configurations based on Y axis sizes of 4, 8 and 16 and X axis sizes up to 32. The smaller matrix sizes in the range are factory reconfigurable up to the maximum size.
-
Product
RF / MW switch
-
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
Product
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)
510180111
SIM Insert
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 310130113 Receiver, i2 MX, 22 Slot VTAC/SIM Insert, EMINot loaded. Thermocouple patchcords need to be purchased separately.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
-
Product
RF Amplifiers
-
Renesas provides a portfolio of RF amplifiers are designed for general purpose video and receiver applications.
-
Product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
-
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
Product
Air Cooled Linear DC Electronic Load
ALx Series
-
The ALx Series utilizes conventional linear MOSFET-based dissipative elements, allowing the series to achieve a very wide voltage-current operating range within the model’s maximum power rating. Using the same heat management innovations developed for Magna-Power’s high density programmable DC power supplies, the ALx Series’ conservative cooling ensures long product life in environments up to 50 °C ambient operating temperature.
-
Product
802.11a,b,g RF Shielded Test Enclosure
JRE 0814-A
-
Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.
-
Product
48V / 200 Amp Load
BD12-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
RF Spectrum Analyzer
FSA-100
-
ShinewayTech® FSA-100 series 6GHz spectrum analyzer are widely used in 2G/3G/4G/5G etc. FSA-100 series have the industry's rare high receiver sensitivity performance with a minimum display average noise level of -165dBm/Hz. Power measurement dynamic range up to 100dB, maximum RF input power exceeds 27dBm. FSA-100 series are equipped with a 7" ultra-large capacitive touch screen (resolution 1024*600). Excellent user experience.
-
-
Product
Low Profile Universal Tension or Compression Load Cell
LPU SERIES
-
Our LPU Series are low profile, universal tension or compression "pancake" type load cells. They are available in 14 ranges from 100 lb through 50,000 lb Hold down bolt holes are provided through the outer diameter and a threaded hole provided through the center for pushing or pulling from either end. The ALB load buttons located in our accessories section, are ideal for compression applications. The LPU Series are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
RF Bridge, 50 Ohm, 300 kHz to 6 GHz
86205A
-
The Keysight 86205A high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
Product
PXI 8x4 RF Matrix 100MHz 75 SMB With Loop-Thru
40-729-101-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, SMB
40-835A-001
Multiplexer Module
The 40-835A-001 (PXI) and 42-835A-001 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
On Load Tap Changer Analyzer
TAP4
-
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
Product
EOL RF Functional Test
AS652
Test Platform
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
Load Banks
-
The only way to be certain that your stationary batteries will perform to specification is to test the batteries’ capacity with a DC load bank / portable battery discharge tester.
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, MCX
42-877A-101
Matrix Switch Module
The 40-877A-101 (PXI) and 42-877A-101 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, SMB
40-877A-002
Matrix Switch Module
The 40-877A-002 (PXI) and 42-877A-002 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 75Ω, MCX
42-832A-101
Multiplexer Module
The 40-832A-101 (PXI) and 42-832A-101 are 75 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PCI 8x9 RF Coaxial Matrix Card 75Ω SMB
50-725A-751
Matrix Switch Module
The 50-725A is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz. The 50-725A is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Multi-Purpose RF Test System
SPA1241
-
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
Product
Load Cells
-
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
