-
Product
Coupling Decoupling Network
TBCDN-M1
-
The TBCDN-M1 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Coupling Decoupling Network
TBCDN-M2
-
The TBCDN-M2 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Lightning Surge Generator
CDN-5810
-
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5810 signal line/data line coupling decoupling network, unshielded symmetrical communication line suitable for surge pulses and ringing wave pulses, designed according to Figure 10 of the new standard IEC61000-4-5.Ed3. It also satisfies ringing Figure 10 requirements of wave standard IEC61000-4-12.Ed2. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
Product
Coupling Decoupling Network
TBCDN-M4
-
The TBCDN-M4 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Three Phase Coupling/Decoupling Network
CDN 3043 Series
-
- Compliant with IEC 61000-4-4 & 5- Universal teminals- no special plugs required- Safety HV plugs and terminals-Manual/programmable EUT power ON/OFF control- Short term overstress capability
-
Product
Mini PCI Express Interface Card
MPCIE-1553
Interface Card
The MPCIE-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for MIL-STD-1553 networks. Coupled with AltaAPI Represents the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software - in an amazingly small package.
-
Product
Coupling Decoupling Network (CDNE)CDN
Emissions
-
CDNEs are based on the CDN as specified in IEC61000-4-6 (Conducted RF Immunity test). In this test, the CDN is used for the coupling of RF onto a cable. In principle, the CDN can be used in reverse, ie coupling any RF on the cable out to an analyser. In an earlier version of EN 55015, these CDNs were specified as suitable for measuring emissions. However, the current version of the standard specifies a CDNE which is essentially a CDN refined to deliver higher accuracy particularly at higher frequencies.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Modules
AXC1553-xT
-
MIL-STD-1553 Test and Simulation modules for XMC with 1 or 2 dual redundant streams plus 8 Discrete I/O’s (on Rear-I/O).*Concurrent BC, MRT (31) and Chronological/Mailbox Bus Monitor*Full Error Injection/Detection (AS4112)*Complex Triggering, Data Capture/Filtering & 100% Bus Recording*Physical Bus Replay*IRIG-B Time Encoder/Decoder*Programmable Bus Coupling, onboard Bus Network and variable Output amplitude*Full Function, Single Function and Simulator Only versions available*Drivers for Linux and Windows*Optional Databus Test and Analysis Software and RT Production Test Plan
-
Product
Coupling Decoupling Network
TBCDN-M3
-
The TBCDN-M3 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Lightning Surge Generator
CDN-5809
-
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5809 signal line/data line coupling decoupling network, unshielded asymmetric communication line suitable for surge pulses and ringing wave pulses, designed according to Figure 9 of the new standard IEC61000-4-5.Ed3. It also satisfies vibration Figure 9 of the ring wave standard IEC61000-4-12Ed2 requires unshielded asymmetry. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
Product
Lightning Surge Generator
CDN-5811
-
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5811 signal line/data line coupling and decoupling network is suitable for 1.2/50us symmetrical high-speed communication line, designed according to Figure 11 of the new standard IEC61000-4-5.Ed3.
-
Product
EFT/Burst Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
High-end test instrument of EFT/Burst for new energy, which fully comply with CE and CCC certification. With a built-in three-phase five-wire automatic coupling /decoupling network EFTN 69100T, it can meet the requirements of new energy test system and high power load test. It is featured with good reliability, stable performance and easy use.
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
Coupling/Decoupling Network
-
Suzhou 3ctest Electronic Co.,Ltd.
coupling/decoupling network is to test the capacity of high speed communication line for surge test. Data transmission rate is up to 1,000MBit/s. It is designed to meet the requirements of figure 14 in IEC/EN 61000-4-5: 2005. The material of decoupling device is high conductive magnetic material. Stable decoupling capacity and transmission rate, easy to use and compact size.
-
Product
CDNs
M Series
-
Coupling Decoupling Networks are recommenced for all power supplies connections. The distubance signals are coupled to each conductor in the supply lines according to EN 61000-4-6 standard. The standard M series CDNs have a current rating of 25 Amps. Com-Power CDNs are available for power supplies from 1 to 5 conductors. These CDNs cover the frequency range of 150 kHz - 230 MHz.
-
Product
Lightning Surge Generator
CDN-58A4
-
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-58A4 signal line/data line coupling decoupling network, suitable for surge pulse and ring wave pulse unshielded symmetrical communication line, according to the new standard IEC61000-4-5.Ed3. Appendix A Figure A4 design. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
Product
CDNE For Emission Measurement On Luminaries
-
CDNs have been used as coupling-/decoupling networks to measureconducted noise as well as for immunity testing so far.
-
Product
Coupling Decoupling Networks (CDN)
-
Beijing KeHuan Century EMC Technology Co,.LTD
Beijing KeHuan Coupling Decoupling Networks (CDN)
-
Product
CDN - Coupling / Decoupling Networks
-
The Coupling- / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal. The requirements for CDN and their application are described in the standard IEC 61000-4-6 (Immunity to conducted disturbances, induced by radio-frequency fields). CDNs have a common mode impedance of 150 Ohm and are available for a multitude of cable types and connectors.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
Threaded Coupling Adapter, G2, G6, G10, ITA, For Conduit Harnessing Assemblies/Clamps
410112599
Coupling Adapter
The Adapter is designed to accommodate military and commercial circular backshells for conduit or strain relief when designing for general and heavy-duty applications. The male thread size is 1.625-18 for this application.
-
Product
PNA-X Microwave Network Analyzer, 43.5 GHz
N5244B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PNA-L Microwave Network Analyzer
N5231B
Network Analyzer
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to 13.5 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PNA-X Microwave Network Analyzer
N5247B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PNA-X Microwave Network Analyzer, 8.5 GHz
N5249B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
Frequency Converter Characterization With Wideband Modulated Signal
N5245BQ
Network Analyzer
The N5245BQ provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements
-
Product
PXI Vector Network Analyzer, 300 KHz To 4 GHz
M9370A
Vector Network Analyzer
The Keysight M9370A PXIe vector network analyzer is a full two-port VNA that fits in just one slot. It can function as a two-port VNA, or with multiple modules can be configured for multiport or multi-site measurements.
-
Product
Streamline USB Vector Network Analyzer, 9 GHz
P5022A
Vector Network Analyzer
Compact, faceless, USB vector network analyzer (VNA). Flexible four or six port VNA which dramatically reduces your size of test. Up to 9 GHz.
-
Product
PXIe Vector Network Analyzer, 100 kHz to 44 GHz
M9807A
Vector Network Analyzer
Full 2 port VNA on a PXI module with flexible applications
-
Product
ENA Vector Network Analyzer
E5071C
Vector Network Analyzer
9 kHz to 4.5/6.5/8.5/14/20 GHz2- or 4-port, 50 ohm, S-parameter test set Improve accuracy, yield and margins with wide dynamic range 130 dB, fast measurement speed 8 ms and excellent temperature stability 0.005 dB/CObtain design confidence through complete characterization of high-speed serial interconnects with enhanced time domain analysis option Protect your investment with upgradability across all of the options Every spec verified, adjustments included Lock in support & peak performance from the start
