Relay Testers
-
Product
Anti-Freeze Tester
AFT-2
-
For testing methanol and ethylene glycol. With green and white scales. Green scale should be used when the engine is hot and white scale should be used when the engine is cold. Testing range: - Methanol - 40°C - 12°C, Ethylene Glycol - 34°C - 12°C. Manufactured with a glass tube, PVC bulb and spout
-
Product
Insulation Tester
AD-2050
-
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
Product
Receptacle Tester
RT500
-
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 67GHz, 50Ω, SMA-1.85
40-780B-574
-
The 40-780B-574 (PXI) and 42-780B-574 (PXIe) are quad SPDT 67GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
Eurorack Module Tester
TST
-
Test your modules safely without reaching into your case! The TST has two keyed 16-pin headers on the front of the module so you can plug and unplug quickly and easily. Two 16-pin plugs are included to shield the power pins when the module is not in use. It also has LEDs to indicate the power status on each rail.
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
-
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
-
Product
Battery Tester
BAT-250-EUR
-
Is designed for one-handed,comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
Product
Configurable Relay Matrix Module
DP-cPCI-4341
-
DP-cPCI-4341 is a Hot-Swappable Configurable Relay Matrix Module. The relays can be operated separately or all at once. The Form A relays can be used to switch voltage signals upto 200V DC. The inputs and outputs are brought out to the fascia for high flexibility. Use of rugged connectors for field terminations ensures long-term reliability. Applications of the module include automatic test equipment, continuity testing, audio telephone line switching and data acquisition system.
-
Product
Cable Tester
CT100
-
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
Product
Pitot-Static Testers
393
-
Aircraft Instrument Support Services, Inc.
*Perform complete Pitot-Static systems functional and leak test*Highly accurate*Built-in safety features*Models available for operation on 115v, 220v and/or no power*Portable hand pump operation
-
Product
Automated Headlight Tester
VLT 0936/MK2
-
Fully computerized controlled CCD Head-light Beam Tester, with fully automated vertical and horizontal movements, with automated searching of the hot spot of the beam. This robot type Headlight Beam Tester is connected to the Vehicle Test Lane Computer system and displays instructions and results to one of the large overhead SVGA monitors of the Test Lane.
-
Product
Static Tester
DRK151
-
Shandong Drick Instruments Co., Ltd.
The tester is applicable in testing the surface potential and the properties of anti-static products .This tester applies to test electrostatic voltage of charged object such as conductor, insulator, and the human body.
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Electric Testers / Multimeters
-
Electrical testing meters from Sper Scientific include our top quality digital multimeters, clamp meters and insulation testers. All Sper meters are designed for the highest levels quality, safety and reliability, with advanced features like True RMS and auto-ranging that add real value and functionality for everyday use.
-
Product
High Voltage Tester
-
The AC /DC High Voltage Test Set that we offer to our clients is widely used at electrical maintenance departments and workshops. It is chiefly used to perform routine maintenance of numerous electrical devices and equipment. Apart from that, this product is used to check the quality of insulation provided in any electrical device.
-
Product
Wiring Tester
WIZE
-
The testers can be used both in production and maintenance, as WIZE® is suitable for simple wiring tests and complex interconnect tests for full systems. WIZE®’s specifications make it compatible with the standard requirements used for testing in the aeronautics, space, rail and defence sectors or any other industry using wiring.
-
Product
Signalling Relays
Q Style / BR930
-
Mors Smitt has expanded its wide range of relay products with the Q-style BR930 signalling relays manufactured by Mors Smitt UK Ltd. in Burton on Trent, UK. We have been manufacturing these relays since the 1960’s and have full Network Rail acceptance certification (formerly British Rail)
-
-
Product
Installation Testers
-
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
DC Hipot Tester
296
-
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
Product
Ground Resistance Testers
-
Whether you are doing a simplified 2-Point, a more complete 3- or 4-Point Fall-of-Potential test, a soil resistivity test or a touch potential test, AEMC has the right instrument for you. Our revolutionary clamp-on ground resistance tester will save you both time and money. Whichever AEMC ground tester you choose, you can count on it to be the highest quality, the most complete package and the simplest to learn to use.
-
-
Product
Oil Tester
-
AJIT Transformer Oil Set is completely self contained, compact & portable unit giving smooth variable output voltage from zero to 60/80/100KV for testing the dielectric strength of insulating oil.
-
Product
Force Tester
CS2 Series
-
The CS2 Series are high quality digital force testing machines optimized for production and laboratory testing of applications up to 5 kN (1100 lbf). These force testing machines are an excellent choice for simple testing within plastic, rubber, packaging, pharma, cosmetic, electronics and wood.
-
Product
Single-in-Line Reed Relays
Series 113
-
SIL relays - Requires a small area of only 0.15 x 0.5 inches (3.8mm x 12.5mm). 10 Watts Form A or 3 Watts Form C switches. Smallest Form C reed relay
-
Product
CrumpleFlex Tester
TF117C
-
TESTEX Testing Equipment Systems Ltd.
The equipment tests a tube of fabric by twisting it through 90o stretching alternately compressing the tube at the same time. After completion of the test the fabric is tested for resistance to penetration by water. CrumpleFlex Tester is fitted with electronic pre-determined counter with automatic stop at a pre-determined number of cycles, also fitted with acrylic plastic interlock safety cover.
-
Product
Comparison Testers
-
Nagman Instruments & Electronics Pvt. Ltd
Comparison testers are used to compare output of Pressure gauges that are under calibration against the ideal pressure output. They can be used to calibrate all pressure types like Hydraulic pressure (liquid), Pneumatic pressure (Gas) as well as Vacuum. Nagman has a wide range of comparison testers for pressure calibration of any type. Comparison testers are very easy to read and the process is very quick and simple in house pressure calibrations. Nagman’s comparison testers can give you a long life with very minimum maintenance. They are ideal for lab use and in house calibrations.
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
