Filter Results:
Products
Manufacturers
Applications
Seismic
earthquaking event with a wave velocity 3-8 km/s.
See Also: Seismometers, Seismic Arrays, Seismic Accelerometers, Earthquake, Geophones, Shear Wave, Wave
-
product
Advanced Seismic Source
GI-SOURCE
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
product
New Generation Marine Seismic Recorder
Seal 428
The Seal 428 is the new large capacity and high-resolution seismic data acquisition system designed for marine towed streamers acquisition. It derives its high reliability and versatility from SERCEL’s extensive experience in cable telemetry systems and from the use of the most advanced electronics and workstation technology.
-
product
High Resolution Seismic Streamer
Sentinel® HR
Sentinel HR is the new Sercel solid streamer designed with a very short channel spacing for high resolution acquisition.
-
product
Seismic interpretation Software
Visual-Sunt
This program is a graphical interface for Windows® of the SUNT program, the 32 bits Windows® version of the SU (Seismic UNIX) freeware, the software for the data processing of “Centre of Wave Phenomena”.
-
product
Seismic interpretation Software
GeoTomCG
GeoTomCG can process crosshole or VSP seismic or radar data. The display shows calculated radar velocities. High velocity zone at depth of 27 m is caused by an abandoned mine. Other zones of contrasting velocities are geological features. S and R indicate source and receiver positions, respectively.
-
product
Test Analysis for Land Seismic Systems
Testif-i Land
Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.
-
product
Seismic interpretation Software Winsism
Winsism
WinSism enables all typical operations for refraction processing including: first break picking, trace phantoming, true velocity, velocity computation, intercept time method, delay method, GRM method. It can also import all usual seismic file format as well as export in raster or vector output.
-
product
High-Resolution Seismic Recording System
DAQlink5
DAQlink 5 is the fifth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system, or a distributed seismic reflection system.
-
product
GEOPHYSICS, SEISMIC, and ATMOSPHERICS RESEARCH RECEIVER
Type RAS-1
Called the RAS-1, the receiver is designed for ultra low and very low frequency scientific research work, including the exploration of low frequency emissions due to seismic and earth-quake activity, study of atmospheric phenomenon such as "whistlers", and low frequency Sudden Ionospheric Disturbance (SID) and electromagnetics phenomenon. The RAS-1 will receive signals from under 200 Hz. To over 250 KHz in both narrow bandwidth modes as well as broad badnwidth reception.
-
product
Seismic Analysis Software
GeoSonics announces our latest software suite. AnalysisNET is the most comprehensive and advanced software for GeoSonics 3000 Series seismograph. The software combines Seismic Analysis and Event Manager software in a single package that employs the .NET framework. AnalysisNET allows easier access to data files provides multiple report combinations and gives you the ability to manage your data.
-
product
Software Package for ZET 048 Seismic Station
ZETLAB SEISMO —
ZETLAB SEISMO Software is included into the delivery scope of ZET 048 seismic recorders. The software and hardware package allows to perform measurements immediately upon measuring instruments connection and drivers installation completion.
-
product
Seismic Signal Conditioners
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
product
Seismic Impact Control System
ZET 048
Seismic impact control system is used to control ground surface shifts caused by earthquakes, explosions and other natural or technology-related factors. Seismic control system is used to obtain actual information of the seismic environment as well as for process facilities state monitoring (in particular, for petroleum industry pipelines systems control).
-
product
Seabed Nodal Solution
GPR
GPRNT is an innovative seabed nodal solution based on Sercel’s leading-edge QuietSeis® technology meeting the very latest seismic industry expectations for performance. The unrivalled digital fidelity and ultra-quiet performance provided by the QuietSeis MEMS sensor ensure a step change in seismic data quality.
-
product
COM Express Type 6 Basic Module With 5th Gen Intel® Core™ I7 & 4th Intel® Core™ I7/i5/i3 & Celeron® Processor And Intel® QM87
CEM880
The CEM880 COM Express Type 6 basic module features 5th generation Intel® Core™ processor (H-processor line), one onboard 4 GB extended temperature DDR3L chip, and one 204-pin SO-DIMM DDR3L socket supporting up to 8 GB. With outstanding computing performance, low power consumption, wide temperature range, and seismic design, the rugged basic-size SoM (system on module) drives Internet of Things innovation and is ideal for graphics-intensive and rich I/O applications such as telecommunication, medical imaging, digital signage, gaming machines, military, and networking.
-
product
Radio Trigger Module
RTM3
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
product
Force Balanced Accelerometer
PA-23, PA-23BH, S-230
The Geotech Model S-230 is a high resolution, 1-component, force balanced accelerometer capable of meeting the noise and stability requirements of the most demanding seismic studies. It features a very wide frequency response (DC to 90 Hz) and an internal calibration coil. Three S-230 accelerometers are packaged as a borehole 3-component unit (Model PA-23BH) and as a surface 3-component unit (Model PA-23). PA-23BH can be submerged up to 100 m depth.
-
product
Portable Load Cell System
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
product
Pioneer Seismic Cabinet
The Pioneer rack is the cornerstone of our broadcast cabinet line, offering flexibility and strength. With a weight capacity of 2,000 lbs., Pioneer’s heavy-duty frame is designed with cross braces interlocked and welded into the corner post.
-
product
Security and Traffic Monitoring System
Information System Technologies Inc.
ISTI’s versatile sensor nodes can support multiple sensing types including acoustic, seismic, visible/IR, and scanning laser. Several eye-safe scanning lasers form a distributed wireless sensor network and can continuously and accurately track as well as monitor ground vehicles and personnel in a surveillance area. This system provides super-fine angular and range resolution to precisely locate moving targets. Among other key benefits are: day/night operational capability, continuous monitoring and surveillance without blind spots, 360 degrees field-of-view, large coverage area, multiple closely spaced target tracking, threat classification, and automatic alarm generation. The system can be used in applications such as traffic monitoring, intrusion detection, border control, airport runway collision and incursion avoidance, and perimeter security.
-
product
Seismic Analysis and Monitoring
Seismic analysis and monitoring have been designed on the base of the contemporary seismic studies. We can offer you a wide range of tools for geophysical surveys, seismic tomography, automated monitoring of bearing structures (structural health monitoring), seismic monitoring of oil piping systems.
-
product
Portable Shakers
The Hardy Shaker ensures that the Seismic Sensors and Transmitters that you have installed are working properly and giving you the results you need. Just like the pressure and flow instruments in your facility need calibration checks every year, so do your Seismic Sensors and Transmitters. This system puts the calibration check of those Seismic Sensors and Transmitters within your control, and within your budget.
-
product
Seismic Sensor
SmartPhone D
Teledyne Marine Real Time Systems
The highly rugged encapsulated SmartPhone D was designed for use with the SmartSource controller, or SmartPhone D system, for real-time monitoring of near-field signatures.
-
product
Transmitters
Seismic transmitters provide a 4-20mA DC signal output proportional to the vibration amplitude, and are ideal for applications where a PLC, DCS, or other automation system will be used instead of a stand-alone vibration monitor. Metrix offers seismic transmitters with a wide variety operating temperatures, frequency responses, scale factors, case materials, connector types, mounting options, and hazardous area approvals.
-
product
Slip Table Assembly
CSTA Series
Unholtz-Dickie introduced the Combined Slip Table Assembly (CSTA) in the late 1960''s to meet the demand for positive mechanical alignment between the shaker and its companion horizontal slip table. The challenge was to achieve this positive, permanent alignment feature without requiring an expensive seismic mass in the vibration lab floor. The original CSTA design has been continuously improved over the years and has now become the industry standard for permanently aligned, integral reaction mass slip tables.
-
product
Seismograph
DX6
The DX6 is a 6 channel seismograph that can be used for almost any seismic project. With its internal memory, optional USB memory and GPS, the flexible DX6 node can be deployed anywhere, at any time.
-
product
XCITE 1200-2 Inertial Mass Excitation System
The Xcite 1200-2 Inertial Mass Excitation system provides a new dimension to structural testing. The ES-302 Exciter contains a 250 lb mass which is accelerated through a 2″ displacement by a hydraulic actuator. The 2,000 lb inertial force which is generated provides ample input to structures such as those shown below to perform low frequency seismic studies and high frequency rotating equipment analyses.
-
product
Seismic Sensors & Transducers
Displacement Pickups are vibration transducers that incorporate a spring-mass system with eddy-current damping using a frictionless pivot. This pivot is a spring flexure that serves as the ‘spring’ and a moment arm attached to the pivot serves as the ‘mass’, which allows resolutions down to the micro inch range. At frequencies above 50Hz, the mass remains fixed in space and becomes an inertial reference. A transducer within the pickup senses the motion of the mounting base relative to the inertial reference and converts it into a proportional signal. Appropriate damping results in a frequency response flat down to 10 Hz. Note that the pickup senses in only one plane, which is perpendicular to the mounting base.
-
product
Seismic Acquistion QC Serivices
Overall data quality / cost monitoring / safety / daily reporting to client. Verif-i provides technical and operational programme assurances for seismic surveys conducted for the company. The lead acquisition QC on-board/on-crew the seismic vessel/block accepts or rejects data on behalf of the company. Our representative will assist the contractor in fulfilling the technical and operational requirements of the seismic programme and report on crew activities.
-
product
Triaxal Seismograph
BC 1313 TRIAXIAL SEISMOGRAPH
BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
