ESD Monitors
-
Product
Air Gap Monitoring & Analysis
-
Solutions for air gap monitoring in order to plan maintenance prior to reduced operating efficiency or damage from magnetically induced heating or rubbing between the rotor and stator.
-
Product
Medium Enterprise Environment Monitoring System
ENVIROMUX-5D
-
The ENVIROMUX-5D supports 5 external configurable sensors, 5 digital inputs, 2 output relays for control of external devices. The system also includes two internal sensors: temperature and humidity. It features 4 USB ports for USB modem, USB flash drive, or USB LCD screen. Linux inside.
-
Product
Helicopter Reducer Vibration Monitor
-
The complex is built on the basis of the measuring platform NI PXI and provides measurement and calculation of vibration parameters. The software of the complex is two-level: the lower hardware level and the upper level of the user interface. The hardware level software provides the following functions:interrogation of measuring modules;signal processing in the time domain;calculation of measuring parameters;spectral analysis;recording the signal to the hard disk.
-
-
Product
Probing, Monitoring & Setting
-
Marposs offers solutions and equipment that make your machine tool an instrument of unprecedented precision, productivity and reliability. Touch probes and laser-based tool setters hold the cutting process accuracy in check. Our balancing actuators and many dedicated sensors guarantee that your machine tool's functional processes never deviate from their specified set points.
-
Product
Gas Monitor
S5000
-
The General Monitors S5000 Gas Monitor is the ultimate gas detector for extreme environments needing to detect oxygen, toxic and combustible gases.
-
Product
Oxygen Deficiency Monitor
Series 1300
-
Deploying a permanently mounted oxygen deficiency monitor in areas where inert gases are stored or piped is highly recommended. Like most things in life, not all oxygen deficiency monitors are the same. Alpha Omega Instruments Series 1300 Oxygen Deficiency Monitor has an array of features and safeguards that makes it today's premier monitor.
-
Product
Audio Loudness Monitoring And Logging System
-
The Mividi® Audio Loudness Monitoring and Logging System (Loudness Logger) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that supports audio decoding, loudness monitoring and logging, log file management and playback. It takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous monitoring and recording over 50 channels simultaneously.
-
Product
Data Monitoring System
1S663-001
-
The 1S663-001 Data Monitoring System was specifically developed for the Cessna Citation X and serves as the primary diagnostic tool for the aircraft?? electronic Logic Modules. The system is FAA certified for airborne operation. Aft compartment and cabin modules can be tested two at a time while remaining in place. The system is also capable of monitoring the fuel quantity system during flight.
-
Product
Digital Microwave Monitor
TX2000
-
This instrument is designed specifically for the field service engineer engaged in the repair and maintenance of domestic and commercial microwave heating equipment working at a nominal frequency of 2.45 GHz. Its purpose is the detection of potentially harmful microwave energy leakage from these heating sources.
-
Product
System Controllers & Battery Monitors
-
UNIPOWER System Controllers & Battery Monitors provide battery management functionality for the Aspiro, Guardian and Sageon DC Power Systems. The proprietary PowCom software enbles the user to monitor multiple Aspiro or Guardian systems at different locations using a highly intuitive GUI. SageView software provides similar fucntionality for Sageon systems and also works with the standalone Sageon Shield battery monitor.
-
Product
PH / ORP Monitor / Controllers
720 Series II
-
The advanced “isolated” circuitry of the 720 Series II pH/ORP Monitor/ controllers guarantees accurate and reliable measurements — completely eliminating ground-loop and noise issues. The unique sensor preamp allows for longer distances between the sensor and the Monitor/controller without the loss of accuracy or reliability.
-
Product
Surface Quality Monitors
-
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable of validating the cleaning quality of all the part cleaning equipment available in the market. Any of SQM model series is capable of verifying metal contamination; monitoring absence/presence of organic and/or inorganic on virtually on surfaces of all metals. They are, price/performance, the most sufficient product available for testing surface of metals for surface cleanliness. These systems operate in an ambient environment, require no sample preparation or deposit of any agents on the surface. In any parts cleaning environment where the quality and efficiency of part cleaning equipment for removal of surface contamination is highly desired, these systems provide a scientific solution by quantitatively measuring the surface cleanliness. The SQM series has the sensitivity and operational simplicity required to provide fast and cost effective surface evaluation for all metals.
-
Product
Indoor Air Quality Monitoring
Si-AQ Expert
-
The Si-AQ Expert is the ideal tool for testing indoor air quality in warehouses and office buildings. It can measure concentrations of multiple different hazardous of gases and compounds that can affect air quality and worker safety.
-
Product
Human Vibration Monitor
HVM200
-
The HVM200 is a small rugged vibration meter with built in Wi-Fi that can be used to measure hand-arm, whole body and general vibration. It includes the metrics and frequency weightings needed to measure human vibration. This 3 channel meter meets the requirements of ISO 8041:2005 and it is designed to measure per ISO 2631-1, 2 & 5 and ISO 5349 in support of the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Values (TLVs) and the directive 2002/44/EC. This makes the HVM200 an ideal choice for an instrument used to demonstrate compliance with human vibration requirements and regulations worldwide.
-
Product
PD Monitoring systems
TECHIMP PD Hub™
-
Techimp’s Partial Discharge (PD) Monitoring systems usually consists of a Central Unit and distributed Data Acquisition Units – the PD Hub™ - able to acquire and process the PD signals locally detected through PD sensors installed on each of main electrical assets (generator, transformer, HV cables and GIS).
-
Product
High-Power Stage Monitors
MJF
-
Between the small footprint of the MJF-208 or the balanced but potent output of the MJF-210, your stage monitor requirements are covered.
-
Product
Energy & Process Monitor
-
Real time monitoring and reportingComposite system with EMS and PEMSDesired reports like, Doff wise, shift wise, count wise, production, energy, UKGSpeed Vs Kw curve, trends, bar graphs, comparisonsAlerts on higher UKG, lesser production, utilization & power fluctuations.Maintenance alerts based on run hours production cost analysis - Cost Audits - Energy Audits
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Audio Monitors
TouchMonitor TM9
-
The all-new audio metering units of the TouchMonitor range is RTW‘s answer to growing requirements in today‘s production, post-production, and broadcast world. Equipped with high-grade 7“ or 9“ touch screens and an easy-to-use GUI, TouchMonitor enters a new level of professional audio metering in terms of precision, performance, efficiency and flexibility.
-
Product
Radio Monitoring and Signal Analysis
-
Shoghi has a full portfolio of products which fulfill the customer requirements for radio monitoring and signal analysis. Shoghi has a very robust SDR based wideband radio monitoring solution which can be implemented both in static or mobile versions for HF and VHF/UHF frequency bands. The Shoghi Radio Monitoring and DF system is the full-fledged product which provides the facilities for wideband signal reception and advanced signal analysis capabilities in addition to both wideband and narrowband D capabilities. The signal analysis capabilities include the ability to demodulate and decode both narrowband and wideband signals and advanced signal protocol analysis for detection of specific data protocols used in the intercepted RF signals.
-
Product
Permanent Noise Monitoring System
831-NMS
-
The Model 831-NMS permanent noise monitoring system is designed for long term monitoring around airports, industrial facilities, motorsport complexes, wind farms, mining operations, and within the general community. Many required accessories are integrated through the INT docking station. Two way remote communication is available for monitoring and control from a central station. Larson Davis provides the hardware, software and open interface to allow this system to be customized for any application or purpose.
-
Product
Environmental Noise Monitors
-
Our noise monitoring equipment is used across a wide range of applications and location. Each of these systems has been designed to meet the exact needs of the user by combining noise monitors with a software and support package.
-
Product
Control & Monitoring
-
Omega has a large selection of control and monitoring devices to chose from. Omega devices can measure anything from gas, liquid, or temperature to process voltages and currents, and much more!
-
Product
Advanced Monitoring Probe
DVB-T/T2
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-T and DVB-T2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
Product
Temperature & Humidity Monitor
-
A humidity sensor (or hygrometer) senses, measures and reports the relative humidity in the air. It therefore measures both moisture and air temperature. The warmer the air temperature is, the more moisture it can hold.
-
Product
Ballast Water Monitoring Systems
-
Ballast water is essential for safe and efficient shipping operations and stabilizing steel-hulled vessels at sea. It provides a variety of critical functions, such as maintaining balance, stability, and structural integrity on non-cargo voyages or when cargo is unloaded. Ballast water is also used to compensate for fuel and water consumption during at-sea operations.
-
Product
Database Performance Monitor
-
Database performance monitoring and optimization for traditional, open-source, and cloud-native databases.
-
-
Product
Electrostatic Dust Monitor
201LP
-
The Redkoh Model 201LP is a three wire particulate monitor that measures particulate levels in air ducts on a real time basis. The Model 201LP is powered by an external 24V dc supply and its continuous 4-20 ma output can be connected directly to a PLC, recorder, or digital readout. Changes in the 4-20 ma output are directly related to changes in the concentration of particulate in the gas stream.
