ESD Monitors
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
Opacity Monitor
DT1000
-
The Datatest Model 1000 is a microprocessor based EPA compliance opacity monitor. The microprocessor creates excellent stability and reliability plus the use of patented glass fiber optic technology in the stack components further enhances the performance. The Model 1000 is offered in a double pass Model 1000 MPD version or a single pass Model 1000 MPS (suitable for harsh applications).
-
Product
Water Distribution Monitor
TW-100
-
HORIBA’s TW-100 is a process water quality measurement system designed for drinking water and water distribution plants. The TW-100 monitors turbidity, color, free chlorine and pressure. This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
-
Product
Panel Mount Monitor
-
Advantech Panel Mount Monitor IDS-3200 series is a touch screen monitor that supports panel, front mount and VESA mount for different integration applications.
-
Product
Mark II Dual Setpoint Monitor
95006
-
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
Product
Panel-mount Type Peracetic Acid Monitor
PM-960
-
A measurement device for continuous measurement of the concentration of peracetic acid used for sterilization in food and beverage processing. The device uses no reagents and is maintenance-free.
-
-
Product
Contamination Monitors
-
Control of X-ray and gamma radiation personal dose equivalent.The dosimeter together with the PC reader and the software forms an efficient automatic system for staff radiation exposure control.
-
Product
Radiation Portal Monitors
-
Baltic Scientific Instruments, Ltd
Radiation Portal Monitors (RPM) are fix-installed radiation detection systems designed for automated screening of pedestrians, vehicles and trains passing through the detection zone of RPM for presence of gamma and neutron radiation. The RPM alerts the security office and front line officer about the presence of radioactive and nuclear material and provides additional alarm associated information: type of alarm (gamma, neutron or both), relative amplitude of the alarm, etc.
-
Product
Spectrum Monitoring Software
-
A comprehensive set of tools for spectrum monitoring, interference analysis, signal identification and geolocation
-
Product
Thermal Monitoring System
-
The monitoring system for the thermal state of traction electric locomotive machines is designed for:control of the thermal state of traction electric motors (TED) as part of a high-speed traction-energy car-laboratory for testing rolling stock (TEL-C) in the acceptance and certification tests of electric locomotives;control of the thermal load of the TED and the temperature distribution by volume of the TED during the operational tests of electric locomotives;experimental determination of the most heated parts of the TED under different operating conditions;display of the current thermal state of the engine to the operator of the system;storing the thermal state data in the database for later playback.
-
Product
Electrical Testing Monitoring
-
The IEC 61850 represents the migration from the analog to the digital world to the substations. Accordingly, industry faces a period of transition, also noticing the effects of IEC 61850 in the traditional checking and monitoring procedures.
-
Product
Ocean State Monitoring System
WaMoS® II
-
is a radar-based, wave and surface current monitoring system that delivers real-time measurements while a vessel is underway, providing germane data to the local operational area. High definition images of wave fields combined with numerical data and intuitive graphical reporting keep the operator well-informed in assessing environmental risk and identifying safe operational windows.
-
Product
Monitoring Relays
-
A Monitoring Relay is a protective control device. The basic functions are to receive input signals, monitor and determine them, and output an alarm signal if a set value (threshold) is reached. Monitoring Relays monitor power supplies (voltage, current, power, phase), temperatures, and other analog signals and detects abnormalities in machines and equipment by determining values against alarm thresholds.
-
Product
20KV 30KV Electrostatic Discharge Generator ESD
ESD-202AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performan
-
Product
Monitor Unit For PAV Series 4-Quadrant Power Amplifier Monitor
-
The 4-Quadrant Power amplifier monitor unit is an optional unit of the PAV series of 4-quadrant amplifiers, which can be assembled into the cabinet.
-
Product
Compressed Air Monitor and Alarm
SENTRY
-
The Edgetech Instruments Model SENTRY detects upset conditions in compressed air systems by constantly monitoring dew point and pressure at the system header or dryer output. The SENTRY alarms when a loss in pressure or high dew point is detected. This information is valuable in detecting compressor failures, system leaks, or drops in dryer performance. A pulsing audible alarm and strobe lamp provide quick notification of upset conditions. The SENTRY also provides a local display of pressure, dew point and system status as well as 4-20mA analog output and alarm relay contacts.
-
Product
Condition Monitoring Solutions
VibroLine
-
The VibroLine devices are stationary analysis modules for continuous condition monitoring on machines and systems. The VibroLine condition monitoring system can be used to monitor vibration acceleration, speed or displacement with freely adjustable frequency filtering for different applications. Permanent vibration monitoring of your machines not only brings competitive advantages through the increased efficiency of your systems, but also protects against unwanted machine failures. With the VibroLine devices, you can monitor not only the sum, order and storage characteristics, but also impact characteristics. This offers you enormous flexibility in terms of monitoring parameters for your condition monitoring.
-
Product
Laser Welding Monitor
I3LASWELD
-
On line Infrared Imaging system for assessing in real time the quality of laser welding processes
-
Product
DP Monitor for Compressed Air Systems
Com.Air
-
The Com.Air dew point monitor has been designed by Edgetech Instruments to offer the highest level of reliability and accuracy available in compressed air system dew point measurement.
-
Product
Measuring & Monitoring Relays
-
Fixed or adjustable threshold for low level or high level voltage or current monitoring.
-
Product
Indoor Air Quality (IAQ) Meters, Monitors
-
For handheld, semi-permanent and long-term IAQ measurement
-
Product
Environmental Noise Monitors
-
Noise is one of the most complained about aspects of the environment, as not only does it have the potential to affect quality of life, it can also be difficult to monitor and therefore control. This type of noise is generally called environmental noise. There are many man-made sources of environmental noise, such as wind turbines, industrial sites, roads and traffic etc. If you are looking for equipment to measure noise in the workplace, look at sound level meters.
-
Product
Database Monitoring
-
Identify and solve database issues that impact application performance! Find out if it’s your code that’s causing problems and learn how to fix database problems without running to your DBA for support. Dynatrace monitors and analyzes the database activity of your services, providing you with visibility down to individual SQL and NoSQL statements. With Dynatrace you see how your application impacts your databases.
-
Product
Data logger and Monitoring
-
Testo offers a wide range of data loggers for long-term recording of measurement data, e.g. for climate or temperature monitoring. Data monitoring systems are recommended for integrated measurement data monitoring. The testo Saveris system offers tamper-proof data recording and WLAN technology that provides access to your measurement data anywhere and at any time on PC, smartphone, or tablet.
-
Product
15.6" 16:9 P-CAP Touchscreen Monitor
USC-M15W
-
15.6" TFT LCD with LED backlight, 16:9 aspect ratio with 1920 x 1080 resolution, Default with P-CAP touch (non-touch option available). IP65-rated front panel, HDMI/USB-C connections, VESA 75 x 75 mounting available.
-
Product
Indoor Air Quality Monitor and Controller
VAT930-CO2/VAT930-CO2-VOC88
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
indoor air quality monitor and controller ( temperature meter. humidity meter . CO2 meter.VOC meter).
-
Product
SSR Monitor
LTT
-
Love Controls LTT Series SSR Monitors allow easy monitoring of the operation of your SSR switches. This handy device compares the input status with the output status. An alarm operates a relay contact to tell you if the load circuit has opened or if the SSR has shorted.
-
Product
Monitoring System
Sensaphone WSG30
-
The Sensaphone WSG30 Monitoring System offers a flexible monitoring solution when hard-wiring sensors is not a cost-effective or viable option. It also functions as a data logger to demonstrate compliance. The WSG30 is encased in a stylish, wall-mountable enclosure with an easy-to-read, 80-character LCD display.
-
Product
SCTE35 And DPI Monitoring System
SCM200
-
The SCTE35 splicing message and advertisement insertion monitoring system can be used by service providers to monitor Ad placement opportunities and verify correct Ad insertion. The system will log all SCTE35 messages discovered in the transport streams and perform triggered recording for the verification of Ad insertion process.
