Phantom Loads
generate different current values based upon the current rating of the energy meter under test. 2) standby power of a device turned off.
See Also: Parasitic Drain
-
Product
DC Electronic Load
EE30141A
-
The EE30141A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices
-
Product
AC Electronic Load
-
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
Product
Resistive AC Load Bank
-
AC load bank testing offers you whole solutions of predictive failure analysis for UPS(uninterrupted power supply), generator, transformers, PV system, inverter etc, to validate the condition and output of such power systems comprehensively. Integrated AC & DC load bank could be made in one unit or separately with different load voltages as per your need for different applications.
-
Product
110V / 90 Amp Load
EL12-110M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 110V Rectifiers and Power Supplies with output Voltages in the range of 100V to 135V and is extremely cost effective.
-
Product
Industrial Weighing - Wireless Load Cells
-
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
Three Phase Load Bank
REOLOAD 310
-
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
-
Product
1800~3000W DC Electronic Loads
JT633 series
-
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
Product
Signal Module, ITA, QuadraPaddle, 480 Position, Fully Loaded For Wire Wrap With Anti-Rotation (610 138 122)
510151127
ITA Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based Mass InterConnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Large Compressive Load Cell
CCLG-3.0
-
DLM’s range of Large Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
AC & DC Action Load Test
-
Shanghai Guantu Technology Co., Ltd.
1. AC action load power supplyVoltage range: 0~1000V;Current range: 5A ~ 100A.2. DC action load power supplyVoltage range: 0~1500V;Current range: 5A ~ 100A.
-
-
-
Product
Load Cells
-
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
Product
Load Boards
-
The Hartmann Load Boards were originally designed for in house use to test, setup and qualify standard chassis and custom systems. As demand for these products presented itself, Hartmann answered the call with a lineup of high quality load boards.
-
Product
Single Point Aluminium Load Cell
EST-4
-
Technopark Automation & Control
The EST-4 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 1200 x 1200 mm. This load cell is available in capacities 1000 kg and 2000 kg.
-
Product
Electronic Loads
SLM DC
-
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
Product
Load Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Load Measurement Trainer comprises of strain gauge based load cell,loading arrangement to load in compression, weights and digital load indicator to read the load in Kg.
-
Product
High Load Strength Tester
HLST1000Z
-
This tester measures the tensile or compressive strength of various samples
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
API Load Testing
loadUI NG Pro
-
With a visual, drag-and-drop interface, loadUI allows you to create, configure and redistribute your Load Tests interactively and in real-time. In a single test environment, loadUI provides complete test coverage and supports all the standard protocols and technologies. And it''s so powerful, it generates scalable, high-volume and real-world load from any number of local and remote computers. Meet loadUI, the future of Load Testing.
-
Product
Oscilloscope, 100 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2104HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
AC Load Bank (Resistive/Reactive)
K-1000 Resistive/Reactive
-
Kongter Test & Measurement Co., Limited
Resistive/reactive load banks are great choices for testing turbines, switchgear, rotary UPS, generators and UPS systems. They can also be used for integrated system testing of utility substation protection systems, particularly for more complex relays like distance, directional overcurrent, power directional and others. A resistive/reactive inductive and/or capacitive load is often required to test solar inverters to ensure solar panels can be stopped from producing electricity in the event of a power outage.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
