Phantom Loads
generate different current values based upon the current rating of the energy meter under test. 2) standby power of a device turned off.
See Also: Parasitic Drain
-
Product
Digital LOOP/PSC/LOAD Tester
2811 LP
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Displays and sound warning if external voltage present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for special orders.● 60Hz available on request.
-
Product
DC Electronic Load
3110 Series（250W~700W）
-
Each 3110 Series stand-alone load has its own control and display panel, CC / CR / CV / CP/ Dynamic modes, also can be controlled intranet via RS232 and USB interface.
-
Product
Load Optimization
CENTRAX CU series
-
A line of advanced, multifunctional heavy-current measurement devices and power meters that integrate programmable logic controller (PLC) capabilities into a single housing.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
48V / 200 Amp Load
BD12-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
Air Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
DC Electronic Loads
-
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Safe Load Indicators
-
Micro Edge Electronics Private Limited
By keeping track with the market development, we are involved in offering world class Digital Load Indicators / Controllers. The offered range is widely used for mV signals from up to four 350 / eight 700 load cells. Our offered range is manufactured using high quality raw material and latest techniques in accordance with the international standards. Appreciated among clients for their high tensile strength, robust construction and optimum efficiency, these are widely demanded all across the globe.
-
Product
Load Banks
EL08 Series
-
*Rectifier Test 8kW*All of our Load Banks are continuously rated for Power and Current.
-
Product
Full Load Testing For Self Priming Pumps With Pneumatic System For Loading & Unloading Of Pumps
-
Aarohi Embedded Systems Pvt. Ltd
While manufacturing of self priming pumps testing time is very important to avoid bottleneck. Aarohi developed semi automatic performance testing system with pneumatic system for loading & unloading of pumps which helps to enhance productivity & work efficiency.
-
Product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Top Load
12R2-8U-TL
-
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
DC Electronic Loads
-
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
Wireless Load Cells
LoadSense
-
We are manufacturers of LoadSense Wireless Load Cells and transducers ranging from 1 to 50 tonnes. If you are not entirely sure about your requirements, please contact us for assistance.
-
-
Product
AC & DC Electronic Loads
-
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
Product
Load Stability Tester
TruMotion™ Acceleration
-
When transport vehicles accelerate, turn or brake, the resulting low-frequency accelerations can cause unit loads to shift. Due to both safety issues and potential product damage/waste, regulatory bodies are requiring testing that’s closer to reality – assuring safe and stable unit load integrity!
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
Resistive Load Banks
R Series
-
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
Product
Resistive & Capacitive, Inductive AC Load Bank
RLC
-
Inductive & capacitive load banks are reactive only and must be used in combination with a resistive load bank to provide the desired load profile to test a power system. Reactive loads banks can provide either a leading power factor (Capacitive) or lagging power factor (Inductive).
-
Product
High Power DC Electronic Load
IT8800 Series
-
IT8800 series has wide power range 150W~10KW, voltage and current measurement speed up to 50KHZ, resolution up to 0.1mV/0.01mA, adjustable measurement current rising speed 0.001A/us~2.5A/us, built-in RS232/GPIB/USB interface. IT8800 series has wide application fields because of its high performance products, it has been applied to LED lighting, aerospace, automotive electronics and other fields.
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
Small Compressive Load Cell
CCSM-3.0
-
DLM’s range of Small Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
20/26 GHz Coax, Insert, Receiver, SIM, 2 POS, 6 Slot (not loaded)
510180110
SIM Insert
20/26 GHz Coax, Insert, Receiver, SIM, 2 POS, 6 Slot (not loaded)20/26 GHz Coax patchcords need to be purchased separately.
-
Product
External Load Module
ELM
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
Economical Bending Beam Load Cells
EBB SERIES
-
The EBB Series is a economical low capacity bending beam load cell suitable for use in a variety of industrial and OEM force measurement and weighing applications. It is made of an aluminum alloy and comes in 1, 2, 5 and 10 kilogram ranges.
-
Product
48V / 300 Amp Load
EL18-48M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
