POST Cards
read BIOS error codes during a Power On Self Test for computers unable to boot-up.
See Also: Cards, Extender Cards, Probe Cards, Test Cards, PCI Diagnostic Cards, Post Codes
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 2.97MΩ
50-298-151
Programmable Resistor Module
The 50-298-151 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 2.97MΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
2-Port SFP Ethernet Card
ECU-P1524PE
-
2-port SFP Ethernet cards supporting HSR/PRP (IEC 62439-3) are specialized NICs designed for zero-delay, high-availability industrial networks. These cards feature dual SFP ports to operate as Dual Attached Nodes (DAN) in HSR ring topologies or parallel PRP networks.
-
Product
Cantilever Probe Cards
Venture
-
Nidec SV Probe’s VentureTM line of cantilever probe cards represents the finest epoxy technology on the market and are perfect for logic testing. The Venture line includes an extensive array of cantilever cards, single to multi-die for a variety of test systems. Other capabilities include: • 3K Points • Pad Pitches as Tight as 35µm • Up to 32 DUTsContact your Nidec SV Probe sales representative to determine which VentureTM product is right for your testing application.
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
PXI 4-Slot BRIC 72X8 Matrix, 2A 2-Pole (3 sub cards)
40-565A-002-72X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
Product
S_A_Relay Card
-
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s, 0 - 20mA, ±20mA) And 2 PCIe Mini Card Slots
IRU152-I
-
*RISC-based (i.MX 6UltraLite) processor 528 MHz*512MB DDR3 SDRAM onboard*8GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi, 3G/4G or LoRa)*4 isolated analog input channels (16-bit, 250 kS/s, 0 - *20mA, ±20mA)*1 isolated COM port*1 isolated DIO (2-in/2-out)*Embedded Linux operating system (Yocto)*Wide operating temperature range from -40°C to +70°C*Supports LabVIEW versions later than 2016*Supports OPC UA
-
Product
Intel® Wireless-AC 9260 Wi-Fi + Bluetooth M.2 2230 Module Card with Cables and Antenna Kit
EWK-M2-AC9260
-
- Bluetooth 5.1- IEEE 802.11ac wave 2 (Wi-Fi 5)- Operating Temperature : 0°C to 70°C (-40°C to 75°C extended)- Compact M.2 2230, A/E key form factor with cable and antenna kit to support flexible installation
-
Product
PXI 4 Slot BRIC 44x16 1-Pole (4 sub cards)
40-562A-021-44X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm With SPDT
50-293-124
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Gigabit Ethernet PCI Express Mini Card
mPCIe-LAN-GbE
-
The mPCIe-LAN-GbE is a type F1 PCI Express Mini Card (mPCIe) optimized for use in mobile and rugged environments, with latching connectors and protection on all signals. The onboard magnetics feature robust built in isolation via transformer coupling. In addition, extended operating temperature and RoHS compliance are standard.
-
Product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
-
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
Multiplexed- Low-Level Function Card
-
Low-level multiplexed systems have a single programmable gain, wide-band amplifier following the input multiplexer. To accommodate low-level signal signals such as those from strain gauges or thermocouples and at the same time high level signals from other sources, the throughput rate must be limited to enable the high bandwidth amplifier to settle to the correct value after switching to a new channel. This results in a relatively low aggregate throughput rate when compared to an amplifier-per-channel system. A major benefit of a well designed low-level multiplexed system is the extremely high performance/cost relationship.
-
Product
PCI 25xDPST Reed Relay Card
50-115A-022
Reed Relay
This is the 25xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PMC Intelligent Interface Card
IIB-3910-PMC
-
The IIB-3910-PMC is an slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the PCI Mezzanine standard.
-
Product
Modular VXI Switch Card Carrier
1260-101
Switch Card
The 1260-101 Switch Carrier accommodates two plug-in switch cards in a single slot VXI module.
-
Product
Smart Card Testers
CT1000
-
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
Product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ Twin Female Contacts and Round Posts
510160122
Receiver Module
Fully Loaded with Twin Female Contacts and Round Posts (Adapter Pins) (p/n's 610138200 and 610138117).Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Square Posts for Wire Wrap with Anti-Rotation (610 138 122)
510151124
ITA Module
NOTE: Part # 510151124 Rev D and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
Product
PICMG 1.3 Half-size CPU Card With Intel® Celeron® Processor J1900 (up To 2.42 GHz), SATA2, CFast™, VGA/LVDS And Dual LANs
SHB215
-
*Intel® Celeron® Processor J1900 up to 2.42 GHz*1 DDR3L-1333/1600 SO-DIMM, up to 8GB*VGA and LVDS with dual-view supported*1 CFast™ socket onboard
-
Product
Real-Time Vision I/O Card With Multifunction
AX92350
-
The AX92350 is a PCI Express x1 vision card with vision-specific I/Os and real-time controls. A machine vision system requires accurate interaction between lighting, camera, actuator and sensor devices. The AX92350 vision I/O card integrates LED lighting controller, camera trigger, encoder input, and digital I/O to connect and control all the vision devices. The encoder input function is well-suited for conveyor applications. There are 4-CH trigger input, 4-CH or 8-CH trigger output, 4-CH LED lighting control, 1-CH quadrature encoder, 8-CH isolated DI and DO, and 1-CH auto measurement function for rugged machine vision and video surveillance applications.
-
Product
Probe Card
-
Japan Electronic Materials Corp.
The probe card is a tool for testing semiconductors used at "Wafer Test" to check quality of IC or LSI in the first process of semiconductor manufacturing. The probe card is expendable.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
CPCI 48 Optically Isolated Outputs Card
CPCI-48OUT
Controller
The output board consists of FPGA controllers for DC output control. An FPGA provides the timing and control. Each output has its own optical isolation, and supports an open collector output. An PCI controller provides the interface to thehost computer. All I/O is accessible from the front panel.
-
Product
Message Based Intelligent Interface Card
IIB-3910-VXI
-
The IIB-3910-VXI is message based intelligent interface card for dual redundant 3910 and 3838 applications. It gives full 3910 and 3838 test, simulation and bus analysis capability on the VXI bus, providing 3910, 3838 1553A, and 1553B variants in a single card. Each channel supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with passive Bus Monitor, and an independent Chronological Bus Monitor (CBM). Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides dual redundant prEN3715 compatible 3910 interface, with variable amplitude dual redundant 3838 interfaces. External trigger-in and trigger-out are provided, with both Primary and secondary bus coupling for direct and stub bus, with access to internal 1553 bus, on the front panel.
-
Product
Fanless Embedded System With Intel® Core™ I5-7300U/i3-7100U & Celeron® 3965U, 2 HDMI, 2 GbE LAN, 4 USB 3.0 And PCI Express Mini Card Slot
eBOX560-512-FL
-
The eBOX560-512-FL is powered by the Intel® Core™ i5-7300U/i3-7100U or Celeron® 3965U processor. To enhance system efficiency, the embedded box PC supports one 260-pin DDR4-2133 SO-DIMM socket with up to 16 GB system memory. Two HDMI ports with up to 4K resolution are supported for dual independent display applications. The palm-sized fanless embedded system is dedicated to smart factory automation, thin clients, industrial controller system, digital signage and retail equipment. Axiomtek's eBOX560-512-FL was designed to operate reliably in industrial and embedded application environments. It is enclosed in IP40-rated heavy-duty aluminum extrusion and steel enclosure and offers a wide operating temperature range from -10°C ~ +50°C (+14°F ~ +122°F) and up to 3G vibration endurance.
-
Product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
-
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
Product
PICMG 1.3 Full-size CPU Card With LGA1151 7th/6th Gen Intel® Core™ Processor, Intel® Q170/H110, SATA3, USB 3.0, Dual LAN And DVI-I
SHB140
-
The SHB140 PICMG 1.3 single board computer is based on the 14nm 6th generation Intel® Core™ i7/i5/i3 processors in the LGA1151 package with Intel® Q170 Express chipset (codename: Skylake). The high performance SHB-based CPU card comes with two DDR4 2133/2400 MHz up to 32GB and six SATA-600 ports with RAID 0/1/10/5. Combined high-bandwidth PCI Express for frame grabbing and conventional PCI expansion for motion capture, the SHB140 is an optimum solution for machine vision and automation applications. This high performance PICMG 1.3 slot CPU card also features an integrated Intel® AMT 11 and TPM 1.2 for higher security and easier maintenance.
