-
product
High Voltage Differential Probes
High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
-
product
LED Tester For Ultra High Power
Electrical Testing: Forward：VF、DVF、VFD、IF、DIF Reverse：VZ、DVZ、IR、DIR AC：VAC、IAC、WAC、PFOptical Testing: can test LOP in cd/mcd/W/mW/lm... from different optical components Wavelength λp,λd,λc,hw,purity,(x,y),CCT,CRIFour-wire measurement and contact resistance in case of deviation. Auto polarity identification and preheat function.Compatible mechanical interface.Optional ESD static test system.
-
product
Test & Measurement Sensors
These application-specific sensors are used in design validation, manufacturing and quality control to ensure passenger safety and improve vehicle performance. Each one is designed to solve a problem or address a technical requirement. Providing custom solutions for customer applications is what HITEC does best.
-
product
Metrology System
Atlas V
The new Atlas V metrology system is designed to measure several key steps that include buried features, not visible by CD-SEM and other techniques. Through remarkable improvements in the optical systems, mechanical sub-systems and software algorithms, the Atlas V system can precisely measure the very subtle variations for device parameters and reveal weak process corners for engineers to improve their process robustness in the fab.
-
product
Earth Resistance & Resistivity Meter
MRU-200
MRU-200 is the only meter in the market which uses all measurement methods.Possible measurements:- earth resistance measurment with 2-pole, 3-pole,4-pole method,- impulse earth resistance measurement, two kinds of measuring impulse 4/10s, 10/350s,- earth resistance measurement without disconnecting measured earths (using clamp),
-
product
Conventional Power Supply Design with Simple Analog Controls
VLF Series
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
product
Test Switches and Accessories
Test switches are designed and manufactured to allow quick and easy multi-circuit testing of switchboard relays, meters and instruments by any conventional system.These test switches and related test plugs have the features necessary for applications involving the measurement of individual currents and voltages associated with substation instrumentation and protection devices. They have been especially designed for the measurement of potential elements, current elements, and make-before-break short-circuit elements related to Current Transformer (CT) circuits.
-
product
Process Calibrators
Handheld calibrator-multimeter of industrial process signals including voltage, current, resistance and temperature. External signals up to 200 V or 100 mA can be measured simultaneously with signal sourcing.
-
product
O-E PROBE
O-E probe is the unit to convert optical signals to electrical signals. It can be connected to Oscilloscopes or data loggers via a BNC connector and monitor the conversion waveform. It can acquire the optical signal easily by just pointing the optical fiber probe at the light source. Recently, more and more light sources utilize optical modulation for next generation lighting such as LED. Acquiring the emission timing is required to measure the emission phenomenon of the light source. This O-E probe unit is the ideal tool for these tasks.
-
product
Cylinder Inner Wall Inspection
The CylinderInspector is an optical, non-destructive inspection and measurement tool for cylinder surfaces.
-
product
cDAQ-9189, 8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785065-02
8-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9189 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly dist...show more -
product
CLAMP ON CTS
P50
Beijing GFUVE Electronics Co.,Ltd.
The P50 is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw.
-
product
Combinated Multimeters
PeakTech Prüf- und Messtechnik GmbH
This combined digital handheld multimeter with the LCR meter function, due to its versatility, can be used universally in the service and maintenance area. In addition to multimeter functions such as voltage, current and frequency measurement, this device also has functions for inductance, capacitance and resistance measurements.
-
product
Portable Luxmeter Data Logger
HD2102.2
Portable luxmeter data logger for measuring illuminance, luminance, PAR, irradiance
-
product
RCD & ELCB Testers
Shanghai Beha Electronics Co., Ltd.
*Ideal for tripping 3mA, 5mA, 10mA, 15mA, 20mA, 30mA, 50mA, 100mA, 150mA, 250mA, 300mA, 500mA RCDs*Accurate digital readout of disconnection time. *Timer Resolution 1ms (max time : 19.99s)*Zero crossing circuitry permit testing at 0° or 180°*Measure voltage between line and earth before testing.
-
product
Online Conductivity Controller
LD-LOCC-A10
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
-
product
Portable heat flux sensor, with read-out unit
HF03 / LI19
Hukseflux Thermal Sensors B.V.
The HF03 is a heat flux sensor that can be used in mobile applications. It is combined with LI19, a high accuracy hand-held read-out unit that can be used both for mobile measurements and as an amplifier directly connected to a PC. The combination HF03 / LI19 is typically used to study heat flux levels around flares and fires, and to calibrate flare radiation monitors / flare heat flux sensors.
-
product
Digital Surface Profile Gauge
NOVOTEST SP-1M
Digital Surface Profile Gauge NOVOTEST SP-1M is designed for profile measuring on either flat or curved surfaces. Also it can be used for measurements of surface roughness (Rz), after abrasive blasting pre-painting work.
-
product
Evaluation Units and Analysis Software
Benefit from over 40 years of experience in inline and laboratory beverage analysis: Connect Anton Paar’s versatile and well-proven evaluation units to all generations of Anton Paar density, sound velocity, concentration and CO2 sensors. Let the data acquisition and visualization software master complex measuring tasks for you – bringing home the precision that marks measurement solutions from Anton Paar.
-
product
Phase Noise Test System
PN9000 System
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
product
Survey Systems
Pair the Smart Chamber with a gas analyzer of your choosing and connect using your mobile device or laptop via the built-in Wi-Fi web server. See live flux data with a LI-COR gas analyzer or connect to a third-party analyzer and the chamber will log GPS and ancillary data for your flux measurements.
-
product
Class 1 Sound Level Meter
Dewesoft class 1 sound level meter is the golden standard for sound and noise measurement. They are extremely easy to set up and friendly to use. Maximum accuracy is assured with certified compliance with international standards. The Dewesoft sound level meters are always at the heart of sound analysis and are suitable for any sort of acoustic measurement.
-
product
Lan Ethernet Digitizer, 14 Bit, 8 Channel 125 MS/s Up To 8 GS Memory
Octopus-X
The GaGe series of Faceless Connected Instruments (FCiX) provide test and measurement professionals new options for integrating high resolution, multi-channel digitizers into Ethernet and LAN enabled measurement systems. The applications served include manufacturing test, automotive test, remote communications monitoring, multi-site semiconductor test, and other solutions where a lightweight but powerful, multi-channel, independent digitizer system is required.
-
product
Circuit Breaker Tester
GDGK-307
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) C-O and O-C time measurement4) Rated operation sequence test5) Bounce time and frequency measurement of breaker closing6) Circuit breaker closing and opening speed measurement7) Travel-time, coil current-time curve of circuit breaker operation measurement8) Travel and clearance of circuit breaker measurement9) Variable DC circuit breaker operation power supply10) Closing arc resistance value and connected time measurement11) Closing time and opening time of graphite circuit breaker measurement12) Print test results by internal micro printers
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-22
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for leakage current measurements*Ultra compact size*AC 1mA～100A
-
product
USB-5132, 50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device
780468-02
50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5132 low-cost oscilloscope device has two channels that sample up to 50 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
product
Floating 6-Ch Integrated Power Source
PM0650
The pulse channels provide voltage pulses with duration control 10us to 100ms, and measures current. The combination of capabilities provides a versatile solution on fulfilling the wide range of requirements on testing a device. The PM0650 may be floated up to ±1500V to facilitate HV isolation test of devices where outputs may be connected directly to line voltages.
-
product
Development Test for Electric Motors with Power Electronics
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
product
Surface Contamination Monitors
Small-sized devices for measuring the ambient dose equivalent rate and the ambient dose equivalent of X-ray and gamma radiation, as well as measuring the flux density of beta particles (AT6130).
-
product
Multi-function Cable Tester
NCT-100-S
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
