Visual Basic
A programming language and environment that allows rapid creation of user interfaces by dragging and dropping elements such as buttons and controls.
-
product
EHC-03 Basic Corrosion Thickness Gages
EHC-03
Danatronics is pleased to welcome our EHC-03 to our corrosion thickness gage family. The EHC-03 is designed to accurately and non-destructively measure metal structures subject to corrosion.
-
product
COM Express® Basic Size Type 6 Module with Up to Hexacore 8th Gen Intel Core™ 8000 Series and Intel Xeon® Processors (formerly codename: Coffee Lake-H)
Express-CF/CFE
The Express-CF/CFE is the first COM Express® COM.0 R3.0 Basic Size Type 6 module supporting the Hexa-core (6 cores) 64-bit 8th Generation Intel® Core™ and Xeon® processor (codename “Coffeelake-H”) with Mobile Intel® QM370, HM370, CM246 Chipset.
-
product
Visual Fault Locator ( VFL)
TM315N
The TM315N Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network during and after installation.
-
product
Basic Pulsed-RF Measurements For VNA Up To 20 GHz
S970250B
Add pulsed-RF measurement capabilities to your P50xxB Streamline series vector network analyzer
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Basic Pulsed-RF Measurements For VNA Up To 53 GHz
S970251B
Add pulsed-RF measurement capabilities to your P50xxB Streamline series vector network analyzer
-
product
Pen Style Visual Fault Locator
CARY-VFLXX
The CAWI-VFLxx Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network duringand after installation.
-
product
COM Express® Basic Size Type 2 Module with 6th Gen Intel Core™, Intel Xeon® and Intel Celeron® Processors (formerly codename: Sky Lake-H)
Express-SL2
ADLINK announces a new COM Express Type 2 Computer-on-Module, based on the highly popular Intel® Core processors (formerly codenamed Skylake and Kaby Lake). The Express-SL2/KL2 supports all type 2 related legacy I/O and thereby allows customers to extend the production life of existing type 2 based systems for at least another 10 years.
-
product
Basic Rate and Primary Rate Simulator
emutel Pro
Emutel Pro has the same features as the Emutel but has 2 BRI and 2 PRI which will allow you to test both basic rate or primary rate equipment or basic to primary links to be set up. Emutel Pro has optional network support and protocol analysis.
-
product
PWB Visual Inspection Machine (AOI/SPI)
RV-2
PWB size: 50mm×50mm - 410mm×360mm 630mm×360mm（longer sized PWB)*. Item of inspection: Missing component,Position displacement, Polarity, Front/rear reversal, Unsoldered,Bridge, Quantity of solder, Lack of insertion component, Character recognition*
