Optical Network
A system of interconnected elements that route light signals.
-
product
Triple IC Optic Node
OX 733
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Tecnology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -13 dBm Sensitivity- RF O/P at 0 dBm : 113 dBµV
-
-
product
Optical Talk Set (Optical Phone & Light Source)
X-5010
This is an efficient instrument that combines in one set the functions of both a digital optical phone and a stabilized light source. It is widely used in operations of installation, optical testing, maintenance, CATV and Telecommunication network. It can carry out full-duplex communication with high quality connection and not be affected by distance. With comfortable hand feelings, and nice outside looking, the user can easily operate on this optical tester.
-
product
Non-contact Optical Surface Profiler
VS-OSP
The VersaSCAN OSP integrates the Base with a high-accuracy, high-speed laser displacement sensor. The OSP technique uses diffuse reflection mechanism to measure topography of a sample. OSP can be used to measure topography, as a very sensitive leveling mechanism, or charting topography to be implemented with other scanning probe techniques for constant-distance mode operation.
-
product
Variable Optical Attenuator
CARY-VA3301B
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
product
Power Networks Test
TX8000
The TX8000 is a 6 Km range Time Domain Reflectometer housed in a rugged over moulded case being water proof to IP67 and drop resistant, designed for outdoor use, but sufficiently small and light weight for general use and may be operated using one hand. Using a 3.5-inch QVGA colour display information is clearly displayed; an illuminated keypad makes the TX8000 ideal for use in poorly lit areas.
-
product
Network Infrastructure
In addition to general support for multiple Mac- and Windows-based operating systems, Applied Computer Technologies can offer support for a variety of inter- and intra-office communications systems for remote or off-site offices, printers and copiers, cabling infrastructure, and more. We can design and implement business continuity systems, to keep your business up-and-running during a disruptive event. Business Continuity includes the ability to communicate with and service your clients even if you and your staff are unable to come to work.
-
product
Data Insights for Network Operators
KALIX
Get outstanding insight of the customers, services and network, end-to-end. KALIX uses machine learning to analyse data and highlight performance issues in services and networks that affect customer. Keep track of all issues and monitor the impact of automation performance.
-
product
RGB Digital Fiber Optic Amplifier
CZ Series
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
-
product
Optical Fiber 1×8 Switch
OFSW - 1 × 8
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×8 is a 1×8 prism optical switch. It can support 1 optical fibers input and 8 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
Photonic Networks and Systems
Fraunhofer Institute for Telecommunications
The Photonic Networks and Systems Division develops solutions for high-performance optical transmission systems for use in in-house, access, metro, long-distance and satellite communications networks. The researchers are focusing on increasing capacity as well as improving safety and energy efficiency. The department has the latest measurement technology, very well-equipped system laboratories, powerful simulation tools and the ability to carry out field tests.
-
product
Networked Absolute Inclinometer
T7
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
product
Optical Oxygen Sensors
The analyzer is suitable for direct field installation (NEMA 4X) in hazardous area (Class I, Division 2). The optical fiber sensor platform allows small inline sensors to be installed into sample tubing lines (1/4”), flow cells using NPT fittings, or directly into tanks or process lines using our retractable “hot tap” sensor design. BOS optical oxygen sensors are impervious to typical O2 poisons (H2S) and interferences (combustibles, magnetic, CO2 and H2) with high accuracy and long-term stability measurements without the need for complex or advanced sample conditioning systems. The threaded version of the optical sensor has optional Dual Seal (ANSI/ISA 12.27.01) classification for high pressure applications up to 1200 PSIG (82.7 BAR).
-
product
Detection of PtG and PtP Faults in Line Networks
LineTroll 110Tμr
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
product
40 GbE Network Attached Storage
HSR40 AC
Curtiss-Wright Defense Solutions
Handling the incoming data is Curtiss-Wright’s CHAMP-XD2, featuring dual Xeon D processors and two built in 40 GbE interfaces. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data. By keeping the data as PCIe, instead of converting it to SATA and sending it to a SATA storage, the data can be directly pipelined over the backplane to the PCIe-based Non-Volatile Memory Express (NVMe) SSDs.
-
product
Portable optical DO meter
ARO-PR
The Portable optical DO meter makes use of the fast-response optical DO sensor RINKO, maintaining its high-speed response performance (99% response < 7sec). The meter probe is equipped with a temperature sensor close to the sensing foil, and the measurements are made by simply inserting the probe into a DO sample bottle (the calibration is carried out using the National Metrology Institute of Japan (NMIJ) certified traceable gases standards). Differently from galvanic electrode sensors, the instrument does not require water sample stirring or fixing reagents, since there is no oxygen consumption. Thus, the required time to estimate dissolved oxygen is considerably reduced. The display unit shows the output instantaneously, and you can check the measured values in real time.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
Complete Network Monitoring
TiSCADA
After years of advanced Research, laboratory and on-field tests, Techimp has developed powerful and effective tools which can help asset managers to take critical decisions and manage power plants in a cost saving ways. Ti-SCADA implements a Real Time condition control of your asset, through a powerful Human Machine Interface (HMI) fully configurable, web based, displaying graphs, charts, trends, KPI, historical data, alarms and customizable reports. Ti-SCADA is a fundamental component of the new generation of Techimp on line condition monitoring systems. Ti-SCADA is designed as a Service Oriented Architecture (SOA) based on interoperability standard for industrial automation - OPC-UA - allowing high performance asset management solutions, tailored on customer needs, to be implemented.
-
product
- Optical / RF Converter
OPT 80
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
product
Optical Light Sources
FLS200 Series
Shanghai Tarluz Telecom Tech Co., LTD
FLS200 Optical Light source could provide maximum 4 wavelengths in one unit, customer could select arbitrary four output wavelengths from 650nm, 850nm, 1300nm, 1310nm, 1490nm, 1550nm. The unit support Single mode and Multimode (50/125um or 62.5/125um MM fiber) optical cable in one unit. It could support FC, SC, ST, LC and 2.5mm universal optical connector.
-
product
Network Cable Tester
AudioJoG Pro 8 Power
Audio/Lighting/Network cable tester with SINGLE & DOUBLE ended testing with memory and intermittent fault detection.
-
product
Fiber Optic Power Meter
Fiber optic power meter is a test instrument used for absolute optical fiber power measurement as well as fiber optic loss related measurement .This hand held type fiber optic test equipment features ingenious appearance,wide range of power measurement, high accurate test precision and user automatic self calibration function. Fiber optic power meter is a tool for telecom and CATV network.
-
product
HPx-346 Analogue to Network Radar Converter
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
product
Near-Field Scanning Optical Microscope Platform
MoScan-F
MoScan-F is a device that enables you to get the best up-to-date available spatial optical resolution using the near field scanning optical microscope (NSOM) principle
-
product
Optical Fiber 1×2 Switch
OFSW - 1 × 2
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×2 is a 1×2 prism optical switch. It can support 1 optical fibers input and 2 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
PAM4 Optical Reference Transmitters
ModBox-PAM4 series
The ModBox-PAM4 serie is a 4-level Pulse Amplitude Modulation (PAM4) Optical Reference Transmitters that generate excellent quality PAM4 optical data streams up to 28 Gbaud, 56 GBaud. The ModBox-PAM4 integrates also: ER4 / LR4: CWDM or LAN-WDM 4 lasers sources, SR4: 850nm laser source, PON: 1310 nm and 1490 nm laser sources.
-
product
Satellite Optical Receiver
SSR-15CW
Hangzhou Softel Optic Co., Ltd.
*Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using high linear PD*Output connected to 5 IN series satellite multiswitch*Build-in optical AGC function*Red-LED for power indication*Smaller size and easier installation
-
product
Optical Power Meter - PXI
Power 1400 Series
The Power 1400 Series optical power meter provides fast monitoring of signal power from -60 to +10 dBm and broad wavelength range of 750 to 1700 nm. With a logarithmic amplifier, it avoids gain-jumps faced by multi-stage linear amplifier power meters.
-
product
DSP, Mixers & Network Interfaces
Analog or digital, our line of mixers and interfaces help you effectively manage multi-microphone installations in boardrooms, city halls, conference spaces and distance learning environments.
