Showing results: 526 - 540 of 1153 items found.
-
SMCV100B -
Rohde & Schwarz GmbH & Co. KG
The R&S®SMCV100B vector signal generator is the first multistandard platform for automotive, broadcast, navigation and wireless applications. This makes the R&S®SMCV100B unique for use in many applications, from the lab to production and wherever different technologies meet.
-
Amprobe Test Tools
Amprobe wireless temperature and humidity testers combine precise, accurate measurement of temperature and humidity with wireless communications up to 80 feet/25 meters to save time and steps. Measure and monitor temperature and relative humidity measurements over time using an Amprobe temperature and humidity data logger. These meters enable you to download measurements to your PC via an USB interface.
-
ENVIROMUX-IPCAM -
Network Technologies Inc
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.0 mm (0.16 in). RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
Eurofins E&E
Eurofins E&E Wireless Device Over-the-Air (OTA), 5G Performance, Bluetooth, PTCRB, and Global Certification Forum Testing.
-
FMC-ZU1RF-A -
Sundance Multiprocessor Technology Ltd.
The FMC-ZU1RF-A is a FMC for RF wireless communications applications based on the AD9371 component from Analog Device Inc (ADI).http://www.sundance.technology/wp-content/uploads/2018/01/FMC-ZU1RF-High-Res-Cutout-e1516095831285.jpgThis FMC is fully hardware and software compatible with the ADRV9371 evaluation board from ADI.
-
EMC Technologies Inc.
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
PMC2mPCI -
Dynamic Engineering
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
Erbessd Instruments, LLC
A Bluetooth Vibration Sensor is an Accelerometer capable of recording vibration data and transfer it to a receiver using Bluetooth standard protocol. These sensors usually integrate an accelerometer and a bluetooth transmitter to establish wireless connectivity. Hence having the capability to connect via peer to peer or mesh network.
-
Go Direct Visible Spectrophotometer -
Vernier Software & Technology, LLC
The Go Direct® Visible Spectrophotometer is a robust and accurate portable visible light spectrophotometer that connects easily to your device via Bluetooth® wireless technology or USB to conduct Beer’s law experiments, kinetic or equilibrium studies of absorbance, or emission spectrum analysis.
-
SMARC -
Advantech Co. Ltd.
SMARC is a small form factor that connects to carrier board by golden finger. It supports low power and wide range computing performance in two module size (82x50mm/82x80mm); also comes with onboard memory & storage. Advantech SMARC is integrated dual LAN and wireless technology.
-
QSM-26 -
Infinite Industrial Informatics Lt
QSM-26 is a DIN rail mount GSM/GPRS MODEM. The unit has a built in Quad Band (850/900/1800/1900MHz) Sierra Wireless Q2687 modem, 2 digital inputs, 2 power relay outputs and a serial RS-232 port. Special AT commands are implemented for TCP/IP based communications.
-
RF Industries
Remote Electrical Tilt (RET) systems are being installed in many wireless infrastructure sites to optimize signal patterns. The RET control cable between the control unit and the antenna is the least appreciated system component, unless you cannot get one to complete your installation.
-
MCCI
The MCCI Catena® 4450 Node for LoRaWAN™ technology is a powerful open-source IoT device designed specifically for use with The Things Network. Based on the Adafruit Feather M0 system, the Catena 4450 is a ready-to-use platform for LoRaWAN 1.0 and 1.1 wireless IoT applications.
-
Artec Ray II -
Artec 3D
With the high-accuracy, long-range, wireless Ray II laser 3D scanner you can precisely and rapidly capture large to massive objects, scenes or areas, and from up to 130 m away. Expect 3D point accuracy that meets high professional standards and best-in-angular-class accuracy.
-
Teradyne, Inc.
Teradyne test solutions are at the forefront of the 5G test era. Why? We work with the leading semiconductor manufacturers and provide optimized test coverage for the major wireless standards. From emerging millimeter wave devices to the traditional sub-6GHz, our test solutions are already leading the way.