Test Receivers
Devices whose purpose is to capture transmitted signal energy and record specified characteristics. These recordings are then examined to ensure that the sending device is working according to specifications. (www.techfest.com)
-
Product
Test Fixture and Test Programing
-
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
Product
Digital Receivers
-
Pentek's digital receiver products cover an extensive range of signal bandwidths. Most of the receiver boards are equipped with Xilinx FPGAs and are supported with Navigator and GateFlow FPGA Design Kit (FDK).
-
Product
PCI Express Receiver Board
AD12-2000-IRIGB
-
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
Product
Thermocouple, Module, Receiver, 90 Series, 64 Position
510104133
Receiver Module
Primary mating module 510108124. (May mate with other ITA modules, as well.)
-
Product
Automotive Electronics Functional Test System
TS-5020
Functional Test
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
Product
Bottom Electrode SMD Test Fixture
16198A
Test Fixture
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
Product
Plus Radio Ethernet Receiver
ACSRF-4040
-
The Plus Radio Ethernet receiver is required as part of the Tinytag Radio Data Logging System. It controls the transmission of data to and from the radio loggers: data received from the loggers is then sent to the computer for viewing with Tinytag Explorer radio software. If power to the computer running the system is lost, the receiver has a battery back-up which will maintain the mesh network until power is restored. This receiver plugs directly into a LAN removing the need for a computer in the area where monitoring is to take place. The receiver is powered using a plug-in Power over Ethernet adaptor (ACS-0041) which is supplied with the unit.
-
Product
Receiver
vLoc3-Pro
-
The vLoc3-Pro utility locator introduces new innovative tools for locating buried utilities assuring damage prevention while gathering information for analysis. With two sets of screened 3D antennas signal distortion is easily detected and displayed on the bright full color display. Along with classic locate screens the vLoc3 series locators offer new locate perspective screens of Vector Locate for fully automatic non-walk over locating, Transverse Graph showing both peak and null simultaneously providing immediate measurement of signal distortion, Plan View showing the relative orientation of the cable at any angle, and a new graphical Sonde screen with guidance arrows leading to the sonde location even when it is vertical.
-
Product
EFT Module for Teststand
test
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
EMI Receiver System
EMI-9KC/EMI-9KB
-
EMI-9KB is an automatic EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KB fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
Product
Testing and Validation
-
DA-Group offers accredited testing services for a wide range of electronic and mobile solutions and products. Testing and measuring are necessary during many phases of product development, manufacturing, verification and delivery. Timely and appropriate testing saves time, because this information is fed back to the development process.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
Product
Free Space Optical Receivers
-
These optical receivers have bandwidths in the DC to GHz range for detecting high speed free space optical signals with the lowest noise and cleanest responses possible.
-
Product
Functional Testing
-
Thanks to our partnership with 6TL engineering (www.6tlengineering.com), we can build complete ATE (Automatic Test Equipment), i.e., turnkey solutions for your testing needs using, high quality, efficient, and modular base test platforms with a short delivery time.
-
Product
Power, Module, Receiver, CASS, 76 Position
510114107
Receiver Module
Module, ID, Cass, Signal, 76 Positions, Discrete Wiring
-
Product
Small-fiber Test
Q-Sense
-
Q-Sense offers a scientifically validated measure of warm, cooland heat-pain thermal sensory thresholds, all clinically usefuldeterminants in the evaluation of neuropathic pain, diabeticneuropathy, chemotherapeutic and other small-fiber neuropathies.
-
Product
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount
510113122
Receiver Module
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount.
-
Product
Test Hardware
TTPSimulate PCI
-
TTPSimulate supports hardware-in-the-loop simulation and design of complex distributed control systems where some parts of the systems are physically available and others exist only as a simulation model. This board enables concurrent engineering and reliable integration of complex integrated systems in large programs.
-
-
Product
Functional Testing
-
Functional Ethernet testing is done during the research and development phase of a product or service. It can cover many parameters depending on the DUT and the application. Using Xena’s products, your range of functional Ethernet testing includes:*Multicast*40/100G PCS and PMA Layer*Transparent Transport*Energy Efficient Ethernet (EEE)*Microbursts and random IFG*Synchronous Ethernet*Automotive Ethernet*1588v2 Performance Testing*Regression testing*Kernel drivers and NIC testing*Hardware emulation (ASIC*)
-
Product
Testing
-
Apogee Labs offers a wide variety of modular chassis types used for test applications with various Data Link Test Modules.
-
Product
UAT testing
-
A successful UAT is crucial for deploying systems with no errors and business risks. However, implementing UAT in an agile environment might lead to frequent and reduced cycles of testing. This mandates UAT testers to develop skills of optimized testing techniques, automation and work in collaboration with the development and QA teams.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
Test System
Series 303
-
The 303-Relay Test System tests the integrity of electromechanical relays and switches. The system can perform an array of tests and control output binning in a fraction of the time of any other tester on the market. Ease of use and overall system flexibility make the 303 ideal for applications in development, incoming inspection, and production line testing.
-
Product
Automotive Testing
-
Kanomax offers a range of unique instruments engineered to make automotive testing and aerospace testing easier. These include Multi-Channel Anemometers, Amenity Manikins with built-in airflow sensors, Thermal Manikins, a Cabin Leakage Tester, Steam Generator, and more.
-
Product
PRODUCTION TESTING
-
The Production Test Department is a component of the Engineering Department where production test technicians perform routine factory testing in accordance with approved test procedures. Most of the electronic testing is automated, whether ambient acceptance testing or environmental ESS testing.
-
Product
Receiver Systems for Monitoring, Surveillance and Logging
-
We produce complete turn-key radio monitoring systems ranging from portable single-channel applications for field tests and drive-by coverage measurements, to large scale computerized multi-channel surveillance systems capable of monitoring thousands of channels simultaneously.
-
Product
Test Contactor
RF Scrub
-
RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.
-
Product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
