GPIB Controllers
-
Product
Qualification and Quality Control Tests
Techsquare
-
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
Product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
-
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
Product
Wind Tunnel Control System
WTCS
-
Wind tunnel facilities are important for the development of all kinds of transportation vehicles. In any kind of wind tunnel - aerodynamic, climatic or acoustic - users are interested in optimization of the valuable factor time for the performance of experiments and measurements. Aerodynamic properties exerting direct influence to fuel consumption have to be optimized.
-
Product
Mass Flow Controller for Low Flow
HFM-200 / HFC-202
-
The HFM-200/HFC-202 is Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers. Featuring reliability and stability, the 200 Series is chosen by OEM's for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.
-
Product
Maximum Demand Controller
-
Nippen Electrical Instruments Co.
NIPPEN Maximum Demand Controller offer demand monitoring with date and time of occurrence. The present and predictive demand are displayed separately. The Maximum Demand Controller (MDC) has 4 relays to facilitate tripping of non essential loads.The trip setting is done according to the contract demand offered by the Electricity Board. Demand control is done by 1) Step Demand Control 2) Forecast Demand Control
-
Product
USB JTAG controller
-
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
Product
Multi-Parameter Monitor / Controller
900 Series
-
Myron L® Company’s new 900 Series Multi-Parameter Monitor / Controllers combine Accuracy, Reliability, Simplicity, and Flexibility. The user intuitive GUI (Graphical User Interface) allows easy and complete programmability of the instrument all from the LCD touch screen. These highly accurate instruments have the ability for simultaneous monitoring and controlling of multiple inputs/outputs.
-
Product
Temperature Controller
2500
-
The Series 2500 Temperature Control provides an impressive array of features in an economical 1/4 DIN package. Features include on-off, time proportioning, proportional, PI, PD, or full PID control, programmable from the front panel, or use Self-Tune PID.
-
Product
Power Factor Controller
-
Rishabh Instruments Pvt. Ltd.,
Is an intelligent power factor controller for reactive power compensation. It has 4 / 6 / 8 control outputs with LED Display for target PF.
-
Product
ORing FET Control
-
Renesas' ORing MOSFET Controllers with a suitably sized N-Channel power MOSFET(s) increase power distribution efficiency and availability when replacing a power ORing diode in high-current applications. They provide gate drive voltage for the MOSFET(s) with a fully integrated charge pump.
-
Product
4-axis Pulse Train Motion Control Modules
HSL-4XMO
-
HSL-4XMO is an advanced 4-axis remote motion control module via HSL bus. Combined with HSL I/O and motion control modules, it can meet many requirements in machine automation (MA) field. HSL-4XMO offers two models - HSL-4XMO-CG-N/P and HSL-4XMO-CD-N/P. HSL-4XMO-CG-N/P is suitable for steppers and linear motors. HSL-4XMO-CD-N/P is suitable for servo motors with transfer cable. Except the advanced motion control library (refer to PCI-8164), ADLINK also provides two extra features for users. Motion Point Table Managements can let users assign the points into the module in advance. Then, users can issue command to continuously move the points without consuming CPU resource. Motion Script Download provides users a easy interface to program the application. With this script, the DSP inside HSL-4XMO can decode the file and execute itself.
-
Product
PXI & PXIe Controllers
-
We offer you a choice of PXI controller options: embedded and remote. Embedded controllers have all the necessary components to operate your PXI system independently without needing an external PC. Remote controllers, on the other hand, allow you to control your PXI system from desktops, laptops, or server computers.
-
Product
Ethernet Controlled Relays And Relay Drivers
-
*ICS's Ethernet to Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the Ethernet to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE or with RPC commands from any Linux/Unix or MAC computer. Use ICS's interactive VXI-11 Keyboard program for easy operation from your PC without having to write a program.
-
Product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
-
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SL
-
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
Product
4-CH Lighting Control Module
AX92353
-
*4-CH independent constant current LED drivers (up to 1 A)*Supports strobe and trigger mode*Intensity control by software*Supports duration and delay time for LED output
-
Product
Stepper Motor Controller for CompactPCI
CPCI321
-
The CPCI321 Intelligent Stepper Motor Controller with amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
4-Channel Motion Control And High-Speed Trigger And Module For The Bridge Connected To EtherCAT
ECAT-4XMO
-
The ECAT-4XMO is EtherCAT SubDevice module with high-speed position comparison trigger and encoder re-drive function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like linear, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
Product
Scienlab Measurement And Control Module
SL1063B
-
The Measurement & Control Module SL1063B is a rack-mount measuring and control module for measuring and switching of digital signals with 16 digital in-/output channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
Product
System Controllers & Battery Monitors
-
UNIPOWER System Controllers & Battery Monitors provide battery management functionality for the Aspiro, Guardian and Sageon DC Power Systems. The proprietary PowCom software enbles the user to monitor multiple Aspiro or Guardian systems at different locations using a highly intuitive GUI. SageView software provides similar fucntionality for Sageon systems and also works with the standalone Sageon Shield battery monitor.
-
Product
Automated System for Visual Quality Control of Markings
Angara 2.0
-
The automated labeling quality control system is designed to identify and reject pharmaceutical labels that have defects in permanent printing (applied in a printing house) and variable printing (applied by an industrial printer as part of a labeling machine).
-
Product
Control and Monitoring of Machines
Millenium 3
-
Easy to program and to implement, it enables the control and monitoring of machines and automation installations with up to 50 I/O. It is positioned right at the heart of the Crouzet Automation range.
-
Product
Attenuation Control Unit, DC to 18 GHz, 0 to 121 dB, 1-dB Steps
J7201B
-
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
-
Product
18.5" WXGA Industrial Monitor With PCAP Touch Control, Direct VGA, And DVI Ports
FPM-7181W
-
18.5" WXGA TFT LED LCD16:9 widescreen aspect ratio, increases viewing area by 40%Supports 10-point multi-touch control via USB interface in Windows 7/8 OSSlim design enables easy installationSupports various mount options: panel, wall, desktop, and VESA armTouchscreen with reliable glass surface and PCAP touch controlRobust system with SECC chassis and IP66-rated magnesium alloy front panelOSD control buttons on rear panelLockable I/O connectors
-
Product
4 Point Probe Sheet Resistance/Resistivity Measurement with Temperature Controled System
TCR-600
-
*Controlled Thermo-chuck (room temperature～600℃/less than 20 minutes)*600C compatible probe head with 1mm linear*Controlled with vacuum sensor, digital thermo-meter, vacuum gauge and gas flow meter*Temperature measuring accuracy：±（0.5% + 1℃）
-
Product
Mass Flow Controller
SEC-E Series
-
This general purpose mass flow controller has a reliable thermal sensor and solenoid valve, allowing you to achieve high-level control of gas flow. A versatile component, the mass flow controller sec-e series can be used in a wide range of industries.Gas flow through the mass flow controller can be controlled over a range of flows: from 10 SCCM to 200 SLM.
-
Product
Electrical Motor Control
-
For more than 60 years, AOIP is specialized in the starting and control of asynchronous cage or slipring motors over any kind of equipment and in any weather conditions.
-
Product
Embedded Control and Monitoring Software Suite (Subscription License)
-
The Embedded Control and Monitoring Software Suite (Subscription License) helps you quickly respond to the changing requirements of your system with software tools that span between OSs, hardware technologies, and I/O types. With a subscription license, lower the upfront cost of purchasing software by buying access to the suite for a year, with the option to renew.LabVIEW is the ultimate design software to efficiently design, prototype, and deploy applications with hundreds of prevalidated libraries, tight hardware integration, and a variety of programming approaches including graphical development, .m file scripts and integration of C/C++, and Python and HDL code.
-
Product
3U PXI-E System Controller
PX32101
-
LinkedHope Intelligent Technologies Co.,Ltd.
PX32101 is a 3U PXI-E system controller based on the newest Intel® Haswell platform. It is designed to provide comprehensive and reliable system controller to support hybrid PXIe-based systems for multiple environments test and measurement applications.Hybrid PXIe-based systems are often required to complete independent diversified complex testing tasks on the PXI test platform. PX32101 provides rich interfaces: 4 USB2.0 / 3.0 for peripheral connectivities; UART for communication or control equipment; dual 1000Base-T Ethernet, one port for LAN connection and the other one for the control of the next generation of LXI instruments.PX32101 can support 4 x4 or two PCIe x8-link, and up to 16GB / s system bandwidth. The ExpressCard 34 expansion slots on the front panel allow users to expand the system modules flexibly. If you install a hybrid multi-slot backplane in the system, then various standard PXI-E and PXI / CPCI peripheral cards could be fitted.In a multitasking environment, PX32101 processor is able to complete multiple tasks independently. The CPU and memory chips soldered with PCB increase reliability performance in shock and vibration environments. Combined with a variety of instrument control interfaces and reliable mechanical & electronic design, PX32101 can meet your hybrid PXIe-based testing for system application requirements perfectly.
