Product

Broadband Detectors

-

Pacific Millimeter Products

Pacific Millimeter Products

These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.

Product

Shunt Voltage References

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices offers a broad line of shunt precision voltage references that combine excellent accuracy and temperature stability with low noise and small packages. These devices operate in a manner that is functionally equivalent to a Zener diode. The bias current must be set higher than the sum of the maximum quiescent current of the voltage reference and the maximum expected load current. Since shunt voltage references are typically biased with a resistor, the voltage reference can operate on a wide range of input voltages.

Product

Distortion Detector

DD-1

-

D'Amore Engineering llc

DD-1 - D'Amore Engineering llc

The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment.

Product

Voltage & Continuity

-

Greenlee Tools

Greenlee Tools

A voltage continuity tester is another way to determine if a circuit breaker needs to be replaced.

Product

Radiation Detectors

-

PCE Instruments

PCE Instruments

A radiation detector is a device for measuring nuclear, electromagnetic or light radiation. A nuclear radiation detector identifies nuclear radiation by measuring the emission of ionizing radiation of alpha particles, beta particles and gamma rays. Also referred to as a geiger counter, a nuclear radiation detector consists of two main elements: the processing electronics and the geiger tube. The geiger tube is filled with low-pressure inert gas like helium, argon or neon. If radioactive radiation occurs, the inert gas is ionized. An anode within the geiger tube registers the quantity of ionized particles numerically correlating with the strength of the radioactive radiation. The radioactivity measurement is then displayed on the LCD screen of the geiger counter or nuclear radiation detector.

Product

Fluorescence Detector

RF-20A/RF-20Axs

-

Shimadzu Corp.

RF-20A/RF-20Axs - Shimadzu Corp.

The excellent basic performance of the Prominence series is further enhanced by the RF-20A/RF-20Axs fluorescence detectors, which offer world-class sensitivity, excellent ease of maintenance, and validation support functions. They support a wide range of applications from conventional analysis to high-performance analysis.

Product

Large-Area CMOS X-Ray Detector

Rad-icon

-

Teledyne DALSA

Rad-icon - Teledyne DALSA

Teledyne DALSA’s Rad-icon product family of large-area digital x-ray cameras offers users a high-speed, high-performance x-ray imaging detector with a fast, reliable PC interface (either GigE or CameraLink) for easy integration.

Product

PXI High Voltage Amplifiers

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

Pickering's PXI High Voltage Amplifiers are ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suit the user’s wiring system.

Product

Flat Panel Detectors

-

Detection Technology Inc.

Detection Technology Inc.

Are a class of solid-state x-ray digital radiography devices similar in principle to the image sensors used in digital photography and video.

Product

Digitally Controlled Ultrasonic Detector

VPE-1000

-

Superior Signal Company

VPE-1000 - Superior Signal Company

he VPE-1000 is perfect for schools, hospitals, hotels, and other large institutional or industrial environments. Use for a variety of leak detection and plant maintenance applications

Product

Leaky Insulator Detector

LIDOR

-

Taurus Powertronics Systems

LIDOR - Taurus Powertronics Systems

The Leaky Insulator Detector (LIDOR) is two-piece hand held non-destructive inspection system which utilizes AC/DC Current sensor and Ultrasonic technology for predictive maintenance. The Leaky Insulator Detector (LIDOR) has a Flexible clamp sensor and Ultrasound Receiver.

Product

Gas Detector

-

Precision Mastech Enterprises Co.

Precision Mastech Enterprises Co.

A device that detects the presence of gases in a volume of space, often as part of a safety system.

Product

Meters for Current & Voltage

EE301-DCM-xx

-

Executive Engineering

EE301-DCM-xx - Executive Engineering

LCD Current Readings:0-80.0 / 40.0 / 20.0. LCD Voltage Readings:0-50.0 / 150.0

Product

Battery Voltage Supervisor

BVS

-

IBEKO Power AB

BVS - IBEKO Power AB

DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.

Product

Portable Flaw Detector

EPOCH 6LT

-

Evident Scientific

EPOCH 6LT - Evident Scientific

Don’t compromise on the inspection capabilities of your flaw detector. The EPOCH® 6LT portable flaw detector combines the functionality of a powerful ultrasonic flaw detection device with a form factor designed to thrive in rope access and high portability applications.

Product

Continuity of Insulation Tester (High Voltage Method)

ZGQ-16B

-

Shanghai Dean Electrical Co., Ltd

ZGQ-16B - Shanghai Dean Electrical Co., Ltd

Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.13-2008Meet GB/T6109-2008 standard requirementsUsed to test the Insulation continuity (namely the pinhole number of enameled wire sample per unit length) of enameled round wires with nominal conductor diameter ranging from0.05mmto1.60mm;8 level test voltages can be selected by pressing button: 350V, 500V, 750V, 1000V, 1500V, 2000V, 2500V and 3000V;Test length ranging 0～99m;Application of SCM control.Automatically complete test process, display wire testing length and pinhole number;Brushless driving motor, guide pulley and take up pulley are equipotent.The electrode insulation to ground, using high resistance material of non-hygroscopic, no leakage, no tracking, easy to clean, Insulation thickness can ensure long-term 3000V voltage effect.Circuit board is subject to anti-static and moistureproof and long-time aging treatment, has more stable quality and higher durability;

Product

Voltage Rectifier

-

Monex Geoscope Pty Ltd

Monex Geoscope Pty Ltd

A voltage rectifier, designed and manufactured by Monex GeoScope Pty. Ltd., has been added to the terraTEM suite of products.  The voltage rectifier has been designed to provide 6 kW, 120 V, 50 A output and is the ideal rectifier to guarantee the necessary stable, ripple free current for the full range of Monex GeoScope’s transmitters.  This includes the internal transmitters for the terraTEM24 (50 A, 120V), terraTEM (15 A, 24 V) and the terraTX-50 external transmitter (50 A, 250 V).  In addition, the voltage rectifier outputs a clean, filtered 24 V suitable for powering either the terraTEM24 console or terraTX-50 console electronics.  And the output stability of the voltage rectifier is not disturbed by the fast turn-off times available on the Monex GeoScope transmitters.

Product

Refrigerant Leak Detector

RLD-1

-

Amprobe Test Tools

RLD-1 - Amprobe Test Tools

Troubleshoot air conditioning systems quickly and accurately with Amprobe RLD-1 Refrigerant Leak Detector. State of the art technology assures precise, unambiguous readings, and makes leak detection across a wide variety of refrigerants easy and quick.

Product

Tin Side Detectors

-

EDTM, Inc.

EDTM, Inc.

Tin Side Detector Lamp (Model # TS1301)Our NEW Tin Side Detector (Model# TS1301) allows you to determine the tin side of float glass. The instrument can test clear float glass or glass that has other specialty coatings applied to it in mos..

Product

Thermal Voltage Converter

1395D

-

Ballentine Laboratories, Inc.

1395D - Ballentine Laboratories, Inc.

The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.