Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
Product
Automatic Calibration Module
ACM2506
-
ACM2506 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 6.5 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
Product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
Programmable Resistor Modules
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
PXIe-2531 PXI Matrix Switch Module, 256-Crosspoint, Reed Relay, .5 A, 60 V
780587-31
Matrix Switch Module
512-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXIe‑2531 is a high-density PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring compact reed relays with switching speeds up to 2,000 cycles/s, the PXIe‑2531 is designed for low‐current, high‐speed switching. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI 8 Slot BRIC 368x4 1-Pole (4 sub-cards)
40-560A-121-368X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
NI-9265, 4-Channel C Series Current Output Module
779334-02
Current Output Module
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
PXI 12-Slot BRIC Matrix, 660x4 1-Pole (15 Sub-cards)
40-562B-321-660X4
Matrix Switch Module
The 40-562B-321-660X4 is a high density BRIC12 matrix module with a size of 660x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
COM-HPC Mini Type Modules
-
The COM-HPC specification add mini type at dimension of 95mm x 70mm in Rev 1.2. It addresses a need seen for a smaller form factor, lower power envelope and lower cost at single 400-pin connector. A single power rail input with 8 to 20-volt range deliver up to 107 watts of power and there are 16x lanes PCIe Gen5 in total.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-343-HI
Programmable Resistor Module
The 40-230-343-HI (PXI) and 42-230-343-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 770kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Gigabit Ethernet
CWDM SFP Transceivers
-
CWDM transceiver modules are offered at wavelengths from 1470nm to 1610nm and include LC connectors. These SFPs are 100% compatible with Cisco equipment.
-
Product
SparkFun GNSS-RTK Dead Reckoning Breakout
ZED-F9K (Qwiic)
-
The SparkFun ZED-F9K GNSS Breakout is a high precision, sensor fusion geospatial board with equally impressive configuration options and takes advantage of u-blox's Automotive Dead Reckoning (ADR) technology. The ZED-F9K module provides a highly accurate and continuous position by fusing a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data, and GNSS measurements.
-
Product
Receiver, G6x, 9 Module
310104481
Receiver
The adaptable G6x receiver integrates a wide variety of I/O options in various module configurations that allow engagement of up to 1,920 signal contacts. The G6x receiver also works with G6 ITAs and the G6x ITA for increased functionality.
-
Product
Analog Multipliers & Dividers
-
An analog multiplier/divider is a device that produces an output voltage or current that is proportional to the product of two or more independent input voltages or currents. In addition to multiplying and dividing, multipliers can perform squaring, square-rooting and modulation functions. Applications include radar, communications, and industrial controls where a real-time response is required. Analog Devices’ offers the widest selection of multipliers and dividers.
-
Product
PXI Ultra High Density Reed Relay Matrix, 33x16, 1-Pole
40-542A-021
Reed Relay
The 40-542A-021 is part of a range of ultra high density matrices. The 40-540A/541A/542A are the world’s highest density single slot PXI reed relay matrix modules and are available as a 132x4, 66x8 or 33x16 matrix with 1-pole switching.
-
Product
Digital I / O modules
-
The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.
-
Product
Qseven® Reference Carrier Board
Q7-BASE
Carrier Board
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the functional requirements for an embedded application, which include, but are not limited to, graphics, audio, mass storage, network and multiple USB ports. A single ruggedized 230 pin MXM connector provides the carrier board interface to carry all the I/O signals to and from the Qseven module. This MXM connector is a well-known and proven high-speed signal interface connector that is commonly used for -PCI Express graphics cards in notebooks.
-
Product
Modulation Distortion Up To 125 GHz
S930712B
-
S930712B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S93072B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel With V/I Readback
41-752A-013
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
RF Amplifiers up to 6000 MHz
-
Includes RF and microwave amplifiers covering the band from 500Mhz to 6000Mhz in a single module with either GaN or GaAs devices. Custom and standard power amplifiers available with high linearity, low noise figure, and very low error vector magnitude (EVM). Our rack systems and select modules include Automatic Gain Control (AGC), Automatic Level Control (ALC), and peak/pulse/average detection useful in OTA, MIMO, and CTIA testing.
-
Product
Signal, Module, ITA, QuadraPaddle, 90 Series, 480 Position, Unloaded
510151106
ITA Module
NOTE: Part # 510151106 Rev E and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150116. (May mate with other Receiver modules, as well.)
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-704-HI
-
The 65-231-704-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors.
-
Product
Ultrasonic Flaw Detector
MFD500B
-
Based on ultrasonic principle, digital ultrasonic flaw detector MFD500B with 320*240 TFT LCD, it can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. It can be used in Laboratory as well as in engineering filed. With range of 0-9999mm, it can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium battery module, it can be long standby for months. High quality with low price, it is the first choice for the practical economic model for ultrasonic testing equipment.
-
Product
D3/D4 Series
-
The D3/D4 connector is capable of mating a wide variety of I/O module configurations, and can engage up to 672 signal contacts. All iDock Series connectors are compatible with VPC's existing line of modules, contacts, and tools.
-
Product
PXI Multiplexer, Single 48-Channel, 1-Pole
40-632A-021-48/1
Multiplexer Module
The 40-632A-021-48/1 is a single 48-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 2x SPST Power Relay, 2 Slot
40-170-001
Relay
Model 40-170 is available either as 2 x SPST High Power Relays, suitable for switching inductive/ capacitive loads up to 30A at 250VAC or as 2 x DPST switching up to 20A. Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
16 / 180 MS/s Bit Waveform Digitizer
WFD16
Waveform Digitizer
The WFD16 is a 16 bit Waveform Digitizer for high-speed / high resolution waveform capturing and analyzing. The fully differential signal path ensures an exceptional high signal quality. Despite this emphasis on signal quality the WFD16 also has a good DC accuracy. The module features differential inputs with a 50 Ohm or 10 kOhm termination and a with a programmable common-mode voltage.
-
Product
10 MHz To 54 GHz USB Wide Dynamic Range Peak And Average Power Sensor
U2066XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
PXI-2584 , 12-Channel, 600 V, 1-Wire PXI Multiplexer Switch Module
778572-84
Multiplexer Module
12-Channel, 600 V, 1-Wire PXI Multiplexer Switch Module —The PXI‑2584 is a high‐voltage PXI multiplexer switch module that is ideal for fuel cell and battery stack applications. The reed relays in the PXI‑2584 ensure longer lifetimes and faster actuation times for test equipment. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
ITA, S6, 6 Module, Inline, 1U
410122103
ITA
This S6 ITA is designed for inline applications and is 1U in height.
-
Product
PXI 4-Slot BRIC Matrix, 220x4 2-Pole (5 sub-cards)
40-562B-022-220X4
Matrix Switch Module
The 40-562B-022-220X4 is a high density BRIC4 matrix module with a size of 220x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Temperature Sensors
-
Our temperature sensors supply important data on the ambient or module temperature in photovoltaic systems.
