Hall Effect
a measurable transverse voltage which occurs when current flows through a conductor in a magnetic field.
-
Product
Hall Effect Measurement system
HMS-3300
-
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
Product
Hall Effect Sensors
-
A new range of sensors based on closed loop hall effect technology, for measuring and monitoring of e.g. secondary transformer overload or shortcircuit detection, DC link from ground fault and overload, motor overload.
-
Product
Hall Effect Systems
-
The MeasureReady™ measurement controller is a revolutionary, all-in-one Hall analysis instrument that delivers significantly higher levels of precision, speed, and convenience to researchers involved in the study of electronic materials.
-
Product
Hall Effect Measurement system
HMS-3000
-
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Product
Closed Loop Hall Effect Current Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
Resistivity and Hall Effect
-
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements.
-
Product
Current Probe With Hall Effect Technology
CP 35
-
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
Product
Hall Effect Vane Sensors
-
ChenYang Technologies GmbH & Co. KG
ChenYang Technologies GmbH & Co. KG supplies various kinds of Hall Effect vane sensors (CYHME301, CYHME56, CYHME2000) for speed measurement with applications to machines, equipments, motorcycles (BMW ), automobile industry etc. We are specialised in design, development and production of Hall-effect sensors and can offer also custom Hall sensors for your special applications.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
Hall Effect Measurement system
HMS-5300
-
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
Product
Photonic Hall Effect
HMS7000
-
Classic hall effect measurement system is to read voltage difference made between both diagonal sides, when flowing current and applying magnet field strength, in perpendicular to flowing current direction. - Photonic hall effect measurement is to read various electrical properties by illuminating light of “various range of wavelength” on the sample, in addition to flowing current and applying magnet field strength. - It is great to see “RGB (Red, Green, Blue), Light intensity vs carrier density, carrier mobility, resistivity, hall coefficient”
-
Product
Hall Effect Measurement system
HMS-5500
-
Variable temp : 80K ~ 350K (model# : AMP55T ) - HMS-5500 can be compatibly used with both low temp magnet kit (model# :AMP55T) and high temp magnet kit (model#: AHT55T5, upto 500dC) - Below image is to show model# HMS-5500 + AMP55T, for low temp.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Hall Effect Sensors
906
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
Product
Hall Effect Proximity Switches/Sensors
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
Product
Hall Effect Measurement system
HMS-5000
-
Constant current source + Van der Pauw method terminal conversion system
-
Product
Hall Effect Probes
-
Magnetic Instrumentation manufactures Hall Effect Probes in a wide range of styles and sizes. Probes are supplied with magnetic, electrical, temperature stability and calibration data for each measurement range.
-
Product
Hall Effect Gear Tooth Sensors and Custom-Made Target Wheels
-
ChenYang Technologies GmbH & Co. KG
ChenYang Technologies GmbH & Co. KG supplies various kinds of Hall Effect Gear Tooth sensors (CYGTS101DC, CYGTS99, CYGTS211, CYGTS212, CYGTS99-198 etc.) for speed measurement with applications to machines, equipments, motorcycles, automobile industry and instruments etc. We are specialised in design, development and production of Hall-effect sensors and can offer also custom Hall sensors for your special applications.
-
Product
Hall Effect Magnet Kit
-
Permanent magnet - Neodium materials - +/- 0.03Tesla deviation can be made in a process of assembling magnet. - However, we indicates correct tesla strength measured by gaussmeter, before shipping magnet kit.
-
Product
Speed Sensors
-
Variohm supply differential hall effect speed sensors for use in motorsport applications. We have two different designs but both offer very high performance.
-
Product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
-
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
Product
Zero Speed Sensors
-
SPECTEC Innovative Sensor Solutions
The Hall effect technology fulfills a wide array of applications due to the Hall effect sensor's ability to detect zero speed and direction change and produce a digital output that is read by computers, motion control devices, position monitors and digital to analog converters.
-
Product
Proximity Sensors
-
Premier Electrosystems is an esteemed name in the manufacturing of inductive proximity switch, photo sensors, capacitive sensors, magnetic sensors, hall effect sensors, analog sensors, encoders, infrared sensors, etc. with NABL calibration certificate
-
Product
Hall Effect Measurement Equipment
HEM
-
The physical quantity of Hall Coefficient, Hall Mobility and Carrier Density etc. can be investigated by measuring at room temperature voltage occurred perpendicularly to the both magnetic field and constant-current when flowing constant-current perpendicularly to magnetic field from current source while applying magnetic field to sample set at the center of magnetic field of magnet.
-
Product
Rotary Hall Effect Sensor
-
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
Product
Current Probes
-
Teledyne LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology, Teledyne LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements.
-
Product
Closed Loop Hall Effect Current Sensors/Transducerswith Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used formeasurement of DC and AC current, pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
