HF
High Frequency operating at 3–30 MHz.
-
Product
HF / HCl Concentration Monitor
HF-960H
-
The HF-960H accurately measures concentrations of hydrofluoric and hydrochloric acid used in semiconductor manufacturing and other processes. The dedicated FES-510 series sensor is made from materials that are highly resistant to chemicals, making this unit ideal for the management of hydrofluoric and hydrochloric acid, even in high concentrations.
-
Product
HF Frequency Counter LXI, GPIB/IEEE48
53210A
-
For fast and accurate frequency and time-interval measurements, you need reliable devices in research and development. The Keysight 53210A HF frequency counter meets the requirements with its high accuracy, bandwidth and speed. Depending on the application and budget, choose one of the three available models. The connection to the PC is via USB, Ethernet/LXI or via GPIB.
-
Product
Antenna Tuner HF+6m
DU 800 T
-
The DU 800 T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 800 T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indiceted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
CO, HF, and DF Laser Spectrum Analyzer
-
Spectrum Analyzers designed for CO, HF, and DF lasers. With wavelength ranges of 2.45 3.25, 4.9 - 6.5, 4.8 5.9, and 3.5 4.2.
-
Product
Perseus SDR HF Receiver
-
PERSEUS is a VLF-LF-HF receiver made by Microtelecom is based on a outstanding direct sampling digital architecture. It features a 14 bit 80 Ms/s analog-to-digital converter with an exceptional 76 dB SNR (BW = 40 MHz), an high-performance configurable FPGA digital down-converter with an up to 1 MS/s output sampling rate and a 480 MBit/s, high-speed USB 2.0 PC interface. Unlike in lower class direct sampling receivers, the PERSEUS RF analog front-end has been carefully designed for the most demanding users and includes a 0-30 dB, 10 dB steps attenuator, a low-loss 10 bands pass-band RF preselector filters bank, and an high dynamic preamplifier with a top-class input third-order Intercept Point of more than 30 dBm. The resulting third-order dynamic range is 103 dB for SSB signals (2.4 KHz BW) and 107 dB for CW signals (500 Hz BW).
-
Product
HF Communication Equipment
MS 2000
-
The Meltronics HF/SSB system provides a reliable voice communication over 2 to 29.99MHz frequency range and is designed to meet the most diverse requirements. The HF system is used to establish communication between Air to Ground station, Air to Air and Air to Ship. This System is suitable for Aircraft, Helicopter and Ships communication applications. The HF transceiver has beyond line of sight communications providing both voice and data services. Systems is a digital, Microprocessor controlled, synthesized unit that utilizes DSP technology to increase performance and versatility.
-
Product
AC Current Probe 10 mV/A, 600A, 12 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable
T3RC0600-HF
-
AC Current Probe 10 mV/A, 600A, 12 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable.
-
Product
HF Low Noise Amplifier
-
The COMM-connect HF Low Noise Amplifier can be used to amplify signals in the HF frequency range. The amplifier comes with a selection of 4 different connectors, which makes it very easy to adapt to any type of installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
AC Current Probe 1 mV/A, 6,000A, 0.055 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil
T3RC6000-LF
-
AC Current Probe 1 mV/A, 6,000A, 0.055 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil.
-
Product
Omnidirectional HF Antennas
-
Kratos Defense & Security Solutions, Inc.
Broadband dipole products include the horizontally polarized 1765 antenna for short-to-medium range communications, the 3065 antenna that reduces ground-area requirements, and the 5065 series designed for locations where space is at a premium, including rooftops.
-
Product
In-line Sensor & Auto Range Switching Concentration Monitor
HF-960EM
-
Measures a wide range of HF concentration from low concentration to undiluted liquid. The HF-960EM achieves high precision measurement by the auto-correction range switching function. Also has the capibility of cleanliness with all PFA sensors. Measurement range: 0 - 50%.
-
Product
Electrosurgical Analyzer
HF-400
-
HF-surgery tester for functional testing of HF surgical devices according to IEC 60601-2-2.
-
Product
AC Current Probe 100 mV/A, 60A, 11 Hz LF Bandwidth, 5MHz HF Bandwidth, 1m cable
T3RC0060-LF
-
AC Current Probe 100 mV/A, 60A, 11 Hz LF Bandwidth, 5MHz HF Bandwidth, 1m cable.
-
Product
Passive Probe, 10:1, 200 MHz, 2-Pack
N2140A
Oscilloscope Probe
The Keysight N2140A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 200 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
Product
Compact Fan Type Ionizers
ER-Q Series
-
Panasonic Industrial Devices Sales Company of America
With Panasonic’s high-frequency AC method and “Sirocco Fan”, the ER-Q Compact Fan Type Ionizer can remove electrostatic charge even at slow fan speeds.ER-Q Ionizers are extremely compact and well suited for removing localized electrostatic charge on manufacturing equipment for electronics or in Semiconductor processes. The ER-Q Ionizers require no compressed air which eliminates air lines and reduces additional maintenance.
-
Product
Power Line EMI Adapters
-
How much EMI noise is on your power lines indeed? How to assess the levels of noise and its properties when it is obviously a bad idea to connect your oscilloscope or a spectrum analyzer directly to your power lines?Our EMI interface adapters provide a barrier for high mains voltages but a straight passage for high-frequency signals so that you can connect your sensitive instrument to power lines for analysis and quantification. We offer plug-in and hand-held adapters which can measure both differential ("normal") and common-mode noise.
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 1 Output, 13.3 V, 14.5 V, 15 A
72-8110
-
The 72-8110 is a compact switch mode Power Supply features a very compact footprint that makes it an ideal match for portable communications equipment. Its 50% duty cycle surge rating is comes in handy in demanding transmitting situations. It is also perfect for two-way radio (including HF) and audio equipment including auto sound and multimedia systems. This fixed voltage switch mode power supply is designed with high RFI stability and is especially suitable for two-way radio and communications equipment. Constant current circuitry is used for overload, short-circuit and over-temperature protection. Output current and voltage drop to a safe level when any fault occurs. This power supply also has over voltage protection to prevent connected equipment from damage.
-
Product
High AC Current Capacitor
LC1/LC2/LC3-AN
-
Induction Heating Processing Equipment, High Current Welding, High Power Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
Product
Products for High-Frequency Measurement
-
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
PID Controller
-
Liquid Instruments' new instrument features real-time frequency-domain conDesign your control system's frequency response using the interactive Bode plotBlock diagram view of the digital signal processing with built-in probe points for signal monitoring2 input channels, 2 output channels with control matrix for blending inputsIncludes single or double integrators and differentiators with low- and high-frequency gain saturationtrol system design capabilities.
-
Product
RF Power Transistors
-
A specialized semiconductor device designed to amplify or switch high-frequency (Radio Frequency) signals, enabling powerful wireless communication in everything from cell phones and Wi-Fi to radar and satellite systems by handling significant power levels at speeds from kilohertz to gigahertz.
-
Product
Reference Frequency Generator
MFCh
-
*Frequency reproduction accuracy ± 2 x 10 -9 *Output frequency 1 Hz - 10 MHz *Output pulse signal 1 kHz The MFC is designed to generate high-frequency pulse signals with a frequency of 1 kHz and a frequency in the range from 1 Hz to 10 MHz along two output lines. The MFC is designed to operate in measuring systems based on the VXIbus trunk. In the MFC, a rubidium frequency standard is used as a reference frequency source. Time to reach the mode when the power source of the rubidium standard is turned on, no more than 10 min
-
Product
LXI Single 24x8 50 Ohm HF Matrix BNC
60-760-005
Matrix Switch Module
The 60-760-005 is a single 24x8 High Frequency Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50Ω and uses BNC signal connectors. It is also available in a smaller enclosure with SMB Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - PCIe
Model 78760
-
Model 78760 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter, it is suitable for connection to HF or IF ports of a communications or radar system.
-
Product
Gravity Handler
-
State of the art model, which features a high throughput capability, eight sites, and high and low temperature measurements, and meets all high-frequence contact requirements. Complete measures to prevent jamming and lead deformation enable high availability. This model is highly regarded by top users around the world because of its high throughput and high reliability.
-
Product
Centralized Motion Controllers
Motion Controller
Pulse train motion controllers generate high-frequency digital signals to control servo motors and steppers, matching performance and precision positioning of high-performance servo amplifiers.
-
Product
Inductors
-
Murata offers a broad lineup of chip inductors that fit diverse requirements such as compact size, large current, etc. across applications ranging from consumer use to automotive applications that require high reliability. We are also productizing inductors with superior mountability thanks to their SMD type that are suited to specific applications such as high-frequency circuits, power supply circuits, in-vehicle PoC, short-range wireless communication, etc.
-
Product
Dual Pitot Tube Flow Meter
PTFM-ONE-DT
-
The Dual Pitot Tube Flow Meter, PTFM-ONE DT is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers, with a sampling rate of 1kHz to accurately measure highly pulsating exhaust flows. This rapid capture rate ensures that any pulsations or exotic behaviour caused by the engine is measured, and the unique design of the PTFM-ONE DT means reverse flows can be calculated, with the same guarantee of sensitivity.
