Variable Optical Attenuators
Adjust the power of an optical signal.
-
Product
Attenuators
-
Reduces the amplitude of a signal without appreciably distorting its waveform.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Optical Transmitter
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* JDSU DFB laser* JDSU External Modulator.*2 optical outputs, 7/9/10/11dBm available.* SBS Threshold 13/16/18dBm adjustable.*Wide AGC range -10~+10dB.* ATC, APC functioned.* Redundant power supply: AC 85~265V and DC -36~-60V.* Supports remote control with JIUZHOU HFC Net-Managing Software via RJ45.
-
Product
Variable Area Flowmeters
-
Variable area flowmeters are the most cost effective solution for almost all applications involving the measurement of industrial process liquids, gases or steam. ABB´s variable area flowmeters are reliable, flexible and simple. They meet the application requirements by featuring a wide range of design varieties and sizes. Technology proven, they offer a long life and high reproducibility. Variable area flowmeters are excellent mechanical back-up meters because no external power supply is needed.
-
Product
Optical tables
-
The primary goal of a well designed optical table is to eliminate relative motion between components of test system located on the surface of the optical table because such motion can generate measurement errors.
-
Product
Lake Variable Area Flow Meters
-
Lake Variable Area flow meters, often referred to as rotameters, measure flow rate of a liquid or gas by relating linear displacement of an internal “float” or sharp-edged orifice plate (Lake) to a corresponding flow rate. As flow rate increases, the orifice area that the flow moves through also increases – thus, the term “Variable Area.” Variable Area meters either allow flow through a peripheral orifice formed between a tapered wall and a float as in the traditional rotameter, or an annular orifice and an internal tapered metering pin in the Lake Monitor.
-
Product
Optics
-
Optics and Photonics Simulation Software. Ansys Optics solutions offer robust design, optimization, and verification simulation software backed by world-class support. These tools empower designers to expedite the development of groundbreaking optical products while improving performance, reliability, and yield. With a suite of top-tier physics solvers, Ansys Optics provides user-friendly workflows for precise multiscale system design, from the nano to macro scale, enabling the design of diverse applications across various industries.
-
Product
Digital Step Attenuators (DSA)
-
High linearity, fast switching time with broad bandwidth. Best-in-class attenuation error with fine attenuation steps. Most robust ESD protection available.
-
Product
Variable Gain High Speed Linear Amplifier
F30PV
-
The F30PV is a very fast general purpose linear amplifier having a variable amplification of 0-10 times and capable of bipolar voltage output of ±35V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Product
Very Low Pressure Variable Reluctance Sensor
DP103
-
The Validyne DP103 is designed for exceedingly low differential pressure measurement applications where high accuracy is required under rough physical conditions. With full scale ranges down to -0.008 psid (-0.56cm H2O), this instrument is being used in the measurement of very low flow rates of gases where symmetrical pressure cavities are required for dynamic response. It is also used in very small leak detection and pressure null detection systems.
-
Product
Fixed Attenuator
FAXE
-
Fixed Attenuators are waveguide components for introduction of some particular attenuation value in to the waveguide network for signal leveling or reflection compensation. The attenuators have two types of design: with resistive plate in the waveguide diagonal plane or using coupling technology. The FAXE 3, 6, 10, 15, 20, 30 dB attenuators are available in waveguide bands from 18 through 225 GHz. The FAXE Fixed Attenuators can be used as laboratory Standards against which other instruments or devices are calibrated in case the parameters of these Fixed Attenuators are stable enough and were measured with appropriate accuracy.
-
Product
SCR CONTROLLED VARIABLE DC POWER SUPPLY
P5085C
-
Shown below is an AC to DC power supply with 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced to a PLC system. These units are customized units, built to order.
-
Product
Optical Square
10777A
Accessory Kit
The Keysight 10777A Optical Square, used with Keysight straightness measurement optics, adds squareness measurement capability to the Keysight5530 Laser Calibration System. The optical square measures the squareness of axes during laser calibration of a machine tool. The Keysight 10777A uses two accurately-aligned mirrors to direct an output beam at precisely 90 degrees to an input beam.
-
Product
Optical Test
-
Optical components such as micro-lenses, diffractive optical elements (DOE), meta optical elements (MOE) and micro lens arrays (MLA) are now largely used on consumer electronics and even more optical elements need to be integrated into smaller and smaller packages. Nowadays mass-production industries key to success lies in increasing the yield by means of strongly automatized testing machines, with statistical analysis.
-
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Fiber Optic Modem
VCH-608
-
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
Product
Optics Test Stations For Single Lenses And Optical Systems
OTS
-
Optik Elektronik Gerätetechnik GmbH
The optics test stations of the OTS series enable the computer-based, software-controlled measurement of optical parameters of individual lenses (including cylindrical lenses) and optical systems. Measured variables are, for example, focal length, MTF, focal length, radius, contact dimension, centering, wedge angle and deflection angle. The optional software module LensTest enables the measurement of the center thickness of lenses and air gaps in complete lenses as well as the measurement of the centering error of individual surfaces.
-
-
-
Product
Optical Fiber Identifier
AFI-400
-
Shanghai Fibretool Technology Co.,Ltd.
AFI-400 Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification work, can be detect in any location of both SM and MM fiber. Meanwhile it also has Visual Fault Locator module with fault location function. It is the ideal instrument for online test.
-
Product
Optical Transmitter
ST1015-10mW
-
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home) Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices*Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
Product
Optical Passive Module
-
Based on thin film technology in Auto Production system, Video Overlay products allow CATV wavelength with IP to be used for uni-or bi-directional transmission. These devices are designed for long life service under the most demanding field conditions.
-
Product
Optical Switches
-
This latest technology platform presents the best value in terms of size, form factor, durability, and cost. The design of our MEMS optical switch centers on DiCon's proprietary dual-axes tilting MEMS mirror and is expandable up to a 1x36 switch configuration. Large fan-out 1xN optical switches and non-blocking fan-out/fan-in NxM matrix optical switches are built by cascading multiple of these 1xN switches. The MEMS 1xN fiber optic switch passes the stringent Telcordia GR-1221 qualification and is vastly deployed in today’s optical communication networks. With a lifetime of over a billion cycles, the durability of this MEMS device makes it a perfect choice for optical network monitoring applications that require frequent switching.
-
Product
Fiber Optic Tests
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
-
Product
Optical Limiting Amplifiers
-
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Product
LXI Optical Switching
-
Our LXI optical switching are fiber optic multiplexers that use MEMS (Micro Electro-Mechanical Systems) switching technology to ensure fast and reliable switching of single or multi-mode optical signals being carried on fiber connections. Our LXI optical switching can be offered for single or multi-mode fibers. This series is focused on multiplexer arrangements – if you are looking for matrix based solutions, please contact us with your requirements.
-
Product
Attenuators
-
A passive electronic device that reduces the power of an electrical or optical signal without significantly distorting its waveform.
-
Product
Optical Fiber Identifier
TM301
-
TM301 Optical Fiber Identifier (Live Fiber Detector) is an essential instrument for the installation and maintenance of optical fiber projects. It can easily detect any spot of SM fiber cables. Through inserting a 1310 or 1550 modulated signal into the fiber, it is used to indicate the direction of the transmitting signals, find and locate the specific fiber without interrupting the normal work during the installation, cabling and maintenance.
